• Journal of the Korean Geotechnical Society
• /
• v.24 no.9
• /
• pp.33-40
• /
• 2008

This paper describes the performance of ground improvement project using prefabricated vertical drains of condition, in which approximately 10m dredged fill overlies original soft foundation layer in the coastal area composed of soft marine clay with high water content and high compressibility. From field monitoring results, excessive ground settlement compared with predicted settlement in design stage developed during the following one year. In order to predict the final consolidation behavior, recalculation of consolidation settlements and back analysis using observed settlements were conducted. Field monitoring results of surface settlements were evaluated, and then corrected because large shear deformation occurred by construction events in the early stages of consolidation. To predict the consolidation behavior, material functions and in-situ conditions from laboratory consolidation test were re-analyzed. Using these results, height of additional embankment is estimated to satisfy residual settlement limit and maintain an adequate ground elevation. The recalculated time-settlement curve has been compared with field monitoring results after additional surcharge was applied. It might be used for verification of recalculated results.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.42 no.6
• /
• pp.722-728
• /
• 1997

This experiment was conducted to establish the cultural practice for reduction of lodging by the effective water management under direct seeding on flooded paddy surface as treated by the drainage times using Dongjinbyeo at National Honam Agricultural Experiment Station during 1994-1995. As the increased midsummer drainage times, the field lodging were reduced by reduction of culm length and large amounts of root with favorable distribution in deep soil, indicating low canopy architecture could promote the light transmission in the plants and favorable root growth. The yield performance was high by increased drainage times which contributed to mainly percentage of ripened grain and 1, 000-grain weight. As a result, two to three times midsummer drainage as effective water management during plant growth was desirable.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.79-84
• /
• 2009

The electron emission source of triode type has been fabricated using CNT paste. The nano Ag particle and photosensitive polymers were added to the CNT paste. The surface roughness of the CNT emitter was uniform by the back exposure method. The added nano Ag particle improves the adhesion and the electric conductance with small variation in the CNTs and between electrode. After the aging with heat-exhausting, the reliability of the triode CNT electron source was secured in the high voltage and current operation for 12 hours. At this time, the gate leakage current was about 10 % less than.

• Geotechnical Engineering
• /
• v.2 no.3
• /
• pp.51-66
• /
• 1986

The design of fabric reinforced retaining wall structure was discussed in this article. It was confirmed that the reinforced retaining earth wall which was designed by new theoretical formulae developed this time was stable structurally and economically. The plastic fabric filter which was placed in layers behind the facing element reduced the lateral earth pressure on the wall elements in comparison with a conventional retaining earth walls. The reinforcing characteristics of earth wall was governed by the spacing of fabric layers, effective length of fabrics, particle distribution and compaction, and thus it is essential that, in the construction field, the reinforcing strips should be selected in order to develop the maximum friction forces bet.eon soil and fabric filters. The maximum tensile stress developed from the reinforcing strips was appeared at a little far distance from the back of skin element and it was not well agreed with the Rankine's theory but distributed well as a symmetrical shape against the point of the maximum tensile stress. The total length of the different layers should be sufficient so that the tension in the fabric strip could be transferred to the backfill material. Also the total stability of reinforced earth wall should be checked with respect to a failure surface which extended blond the different lathers.

• Current Photovoltaic Research
• /
• v.7 no.1
• /
• pp.9-14
• /
• 2019

Carrier selective solar cell structure has allured curiosity of photovoltaic researchers due to the use of wide band gap transition metal oxide (TMO). Distinctive p/n-type character, broad range of work functions (2 to 7 eV) and risk free fabrication of TMO has evolved new concept of heterojunction intrinsic thin layer (HIT) solar cell employing carrier selective layers such as $MoO_x$, $WO_x$, $V_2O_5$ and $TiO_2$ replacing the doped a-Si layers on either front side or back side. The p/n-doped hydrogenated amorphous silicon (a-Si:H) layers are deposited by Plasma-Enhanced Chemical Vapor Deposition (PECVD), which includes the flammable and toxic boron/phosphorous gas precursors. Due to this, carrier selective TMO is gaining popularity as analternative risk-free material in place of conventional a-Si:H. In this work hole selective materials such as $MoO_x$, $WO_x$ and $V_2O_5$has been investigated. Recently $MoO_x$, $WO_x$ & $V_2O_5$ hetero-structures showed conversion efficiency of 22.5%, 12.6% & 15.7% respectively at temperature below $200^{\circ}C$. In this work a concise review on few important aspects of the hole selective material solar cell such as historical developments, device structure, fabrication, factors effecting cell performance and dependency on temperature has been reported.

• Journal of Astronomy and Space Sciences
• /
• v.27 no.2
• /
• pp.153-160
• /
• 2010

We modified the optical system of 500 mm wide-field telescope of which point spread function showed an irregularity. The telescope has been operated for Near Earth Space Survey (NESS) located at Siding Spring Observatory (SSO) in Australia, and the optical system was brought back to Korea in January 2008. After performing a numerical simulation with the tested value of surface figure error of the primary mirror using optical design program, we found that the surface figure error of the mirror should be fabricated less than root mean square (RMS) $\lambda$/10 in order to obtain a stellar full width at half maximum (FWHM) below $28\;{\mu}m$. However, we started to figure the mirror for the target value of RMS $\lambda$/20, because system surface figure error would be increased by the error induced by the optical axis adjustment, mirror cell installation, and others. The radius of curvature of the primary mirror was 1,946 mm after the correction. Its measured surface figure error was less than RMS $\lambda$/20 on the table of polishing machine, and RMS $\lambda$/15 after installation in the primary mirror cell. A test observation performed at Daeduk Observatory at Korea Astronomy and Space Science Institute by utilizing the exiting mount, and resulted in $39.8\;{\mu}m$ of stellar FWHM. It was larger than the value from numerical simulation, and showed wing-shaped stellar image. It turned out that the measured-curvature of the secondary mirror, 1,820 mm, was not the same as the designed one, 1,795.977 mm. We fabricated the secondary mirror to the designed value, and finally obtained a stellar FWHM of $27\;{\mu}m$ after re-installation of the optical system into SSO NESS Observatory in Australia.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.77.2-77.2
• /
• 2010

스크린 프린팅을 이용한 태양전지에서 전극소성 시 알루미늄 후면 전극이 실리콘으로 확산되어 후면전계(Back Surface Field)를 형성한다. 후면전계 형성시 알루미늄과 후면전계 사이에 알루미늄-실리콘 합금이 형성된다. 이 알루미늄-실리콘 합금은 알루미늄 후면전극의 전기전도도 및 휨현상, bead 형성 등에 영향을 끼친다. 본 논문은 알루미늄 페이스트에 첨가된 Glass frit이 알루미늄-실리콘 합금 형성에 끼치는 영향을 관찰하였다. 분산제, 유기바인더, 알루미늄을 섞어 1개의 페이스트를 만들었고, Glass frit을 1%, 2%, 3%, 4%, 5% 씩 첨가하여 총 6개의 알루미늄 페이스트를 만들었다. 절삭손상이 제거된 실리콘 기판의 후면에 알루미늄 페이스트를 스크린 프린팅하여 전극을 소성하였다. 주사전자 현미경(SEM)을 사용하여 시편의 단면사진으로부터 Glass frit 함량에 따른 알루미늄-실리콘 합금층의 변화를 관찰하였다. Glass frit이 첨가되지 않은 페이스트는 소성 후 알루미늄-실리콘 합금이 두껍게 형성되었으나, Glass frit이 첨가된 페이스트는 소성 후 알루미늄-실리콘 합금이 얇게 형성되는 결과를 얻었다. 또한 Glass frit을 첨가함에 따라 표면의 원형 모양의 무늬가 작아지면서 3%부터는 사라지는 것을 확인할 수 있었다.

• Current Photovoltaic Research
• /
• v.6 no.2
• /
• pp.43-48
• /
• 2018

The traditional silicon heterojunction solar cells consist of intrinsic amorphous silicon to prevent recombination of the silicon surface and doped amorphous silicon to transport the photo-generated electrons and holes to the electrode. Back contact solar cells with silicon heterojunction exhibit very high open-circuit voltages, but the complexity of the process due to form the emitter and base at the backside must be addressed. In order to solve this problem, the structure, manufacturing method, and new materials enabling the carrier selective contact (CSC) solar cell capable of achieving high efficiency without using a complicated structure have recently been actively developed. CSC solar cells minimize carrier recombination on metal contacts and effectively transfer charge. The CSC structure allows very low levels of recombination current (eg, Jo < 9fA/cm2), thereby achieves high open-circuit voltage and high efficiency. This paper summarizes the core technology of CSC solar cell, which has been spotlighted as the next generation technology, and is aiming to speed up the research and development in this field.

• Korean Journal of Materials Research
• /
• v.13 no.5
• /
• pp.313-316
• /
• 2003

The new epitaxial base cell as a high efficiency Si solar cell was fabricated and the effect of buried contact on the cell characteristics was investigated. In our experiments, the cell with buried contact showed the open circuit voltage of 0.62 V, the short circuit current of 40 mA, the fill factor of 0.7, and the efficiency of 10% under the incident light of AM-1 100 ㎽/$\textrm{cm}^2$. The insertion of buried contact in the epitaxial base structure brought the fabricated cell to the efficiency improvement of about 33%. The cell proposed in this paper has the structural superiority in the fabrication of high efficiency solar cell due to the carrier drift transport in the optical absorption region and the formation of back surface field by $p^{－}$ $p^{+}$ epitaxial base, and the reduction of emitter series resistance by n＋ buried contact.

• Journal of Power System Engineering
• /
• v.21 no.2
• /
• pp.48-56
• /
• 2017

The steady-state, incompressible and three-dimensional numerical analysis was carried out to evaluate the velocity fields around the seabed tiller used for the improvement of the seabed soil and the pulling force and buoyancy generated by driving the seabed tiller. The turbulence model used in this study is a realizable $k-{\varepsilon}$ well known to be excellent for predicting the performance of the flow separation and recirculation flow as well as the boundary layer with rotation and strong back pressure gradient. As a results, a typical vortex pair appears near the adjacent rotor vane tip. When the current is stopped, there is no force when pulling the seabed tiller, but when the current flows at 1.2 knots, the force acts on the downstream side and the pulling force is much greater. In stationary currents, the buoyancy of the seabed tiller acts more strongly towards the seabed as the number of rotations of the rotor increases, but acts more strongly toward the sea surface at 1.2 knots of current.