• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2004년도 춘계학술발표회
• /
• pp.285-292
• /
• 2004

Earth Anchor method as a supporting system is widely used in the large scale deep excavation of urban areas or slope excavation project. Considering the application frequency of that method and catastrophe of that method under unproper construction management, we can find out many problems relevant to the domestic design and construction management of earth anchor method. When we encounter the cases of rapid increments and various decrements in earth anchor axial forces, considering the characteristic of earth anchor method, it is an essential point to catch the reasons and to prepare countermeasures. This article introduces two actual monitoring examples based on the close analyses of measured data in a typical large scale deep excavation project and slope excavation project. One is a rapidly increasing case of earth anchor axial forces with the continuous advance of incremental deformation in a geological layer interface. And another is a decreasing case of earth anchor axial forces with the construction conditions. The effort of this article aims to improve and develop the technique of design and construction in the coming projects having similar ground condition and supporting method.

• Journal of Electrical Engineering and Technology
• /
• 제7권2호
• /
• pp.184-192
• /
• 2012

The torque and unbalanced magnetic forces in permanent magnet machines are resultants of the tangential, axial and normal magnetic forces, respectively. Those are in general influenced by pole-teeth-winding configuration. A study of the torque and unbalanced magnetic forces of a small flux concentrating permanent magnet transverse flux machine (FCPM-TFM) in segmented compact structure is presented in this paper. By using FLUX3D software from Cedrat, Maxwell stress tensor has been solved. Finite element (FE-) magneto static study followed by transient analysis has been conducted to investigate the influence of unsymmetrical winding pattern, in respect to the rotor, on the performance of the FCPM-TFM. Calculating the magnetic field components in the air gap has required an introduction of a 2D grid in the middle of the air gap, whereby good estimations of the forces are obtained. In this machine, the axial magnetic forces reveal relatively higher amplitudes compared to the normal forces. Practical results of a prototype motor are demonstrated through the analysis.

• Earthquakes and Structures
• /
• 제20권2호
• /
• pp.161-173
• /
• 2021

The structural behavior of a tensile fabric structure, known as hypar, is investigated. Seismic-induced stresses in the fabric and axial forces in masts and cables are obtained using accelerograms recorded at different regions of the world. Time-history analysis using each recording are performed for the hypar by using finite element simulation. It is found that while the seismic stresses in the fabric are not critical for design, the seismic tensile forces in cables and the seismic compressive forces in masts should not be disregarded by designers. This is important, because the seismic design is usually not considered so relevant, as compared for instance with wind design, for these types ofstructures. The most relevant findings of this study are: 1) dynamic axial forces can have an increase of up to twice the static loading when the TFS is subjected to seismic demands, 2) large peak ground accelerations seem to be the key parameter for significant seismic-induced axial forces, but not clear trend is found to relate such forces with earthquakes and site characteristics and, 3) the inclusion or exclusion of the form-finding in the analysis procedure importantly affects results ofseismic stresses in the fabric, but not in the frame.

• 한국우주과학회:학술대회논문집(한국우주과학회보)
• /
• 한국우주과학회 2004년도 한국우주과학회보 제13권2호
• /
• pp.258-261
• /
• 2004

Numerical simulations are made to predict the axial force coefficients of a two-stage launch vehicle, and the results are compared with those by wind tunnel tests. It is found that the forebody axial force is not affected by whether the base of the body is modeled or not. Modeling the sting support used in wind tunnel tests reduced the base axial force compared to the results without it. The present calculation shows that the forebody axial forces are underestimated while the base axial forces are overestimated. The total axial force, therefore, compares with the experimental data with better accuracy by cancelling out the errors of opposite signs. Modeling of the sting support in numerical simulations is found to be necessary to get a better agreement with the experiments for both base and overall axial force coefficients.

• 한국강구조학회 논문집
• /
• 제9권3호통권32호
• /
• pp.421-430
• /
• 1997

본 연구에서는 숏브라스트한 후 무기징크 페인트로 도장한 무기징크면, 연마면, 흑피면에 대하여 정적 및 피로시험을 수행하여 기존의 연구결과와 비교평가함으로써 마찰면의 표면상태에 따른 고장력볼트 마찰이음부의 정적 및 피로거동을 규명하고자 하였다. 본 연구의 목적을 달성하기 위하여 일련의 정적 및 피로시험을 실시하고 토크관리법의 타당성 평가, 미끄러짐계수의 도출, 도입축력의 감소률 규명, 피로강도의 평가, 마찰면의 압축력 분포 조사 등을 수행하였다. 본 실험결과와 기존 연구자들의 연구결과를 종합적으로 검토한 결과 볼트의 설계축력 도입을 위한 토크관리법은 타당하며, 시간경과 및 반복하중의 작용에 따른 축력감소율을 고려할 때 설계축력의 110%로 초기축력을 도입하도록 규정한 시방서 기준은 적합한 것으로 평가되었다. 시간경과에 따른 도입축력의 초기감소율은 경과시간의 상용로그에 비례하는 것으로 나타났으며, 도입직후 약 20시간이 경과하면 일정한 값으로 수렴되고 있음을 알 수 있었고 이들은 마찰면의 표면조도와는 상관관계가 없는 것으로 평가되었다. 미끄러짐계수는 연마면, 무기징크프라이머 도포면, 흑피면 순으로 크게 나타났으며 미끄러짐하중은 도입축력에 크게 좌우되나 도입축력이 크면 마찰면의 표면조도의 손상으로 인하여 미끄러짐계수가 작아져 도입축력과 미끄러짐하중 사이에는 선형적 비례관계가 성립되지 않음을 알 수 있었다. 마찰면의 압축력 분포를 조사한 결과 내측볼트 주변의 마찰면적이 외측볼트 주변보다 응력방향에 있어서 더 넓게 분포하고 있는 것을 알 수 있었으며, 이는 외측볼트로부터 마찰접합에서 지압접합으로 천이되고 있는 것으로 판단된다.

• 한국기계가공학회지
• /
• 제20권3호
• /
• pp.92-99
• /
• 2021

An automatic transmission, which consists of several decks of planetary gear sets, provides multiple speed and torque ratios by actuating brakes and clutches (mechanical friction components) for connecting central members of the planetary gear sets. The gear set consists of the sun gear, the ring gear, and the carrier supporting multiple planet gears with pin shafts. In designing a new automatic transmission, there are many steps to design and analyze: gears, brakes and clutches, shafts, and other mechanical components. Among them, selecting thrust bearings that not only allow the relative rotation of the central members and other mechanical components but also support axial forces coming from them is important; doing so yields superior driving performance and better fuel efficiency. In selecting thrust bearings, the magnitude of axial forces on them is a critical factor that affects their bearing size and performance; its results are systematically related to the direction of the helical angle of each planetary gear set (a geometric design profile). This research presents the effects of the helical angle direction on the axial forces acting on thrust bearings in an automatic transmission consisting of planetary gear sets. A model transmission was built by analyzing kinematics and power flows and by designing planetary gear sets. The results of the axial forces on thrust bearings were analyzed for all combinations of helix angle directions of the planetary gear sets.

• Coupled systems mechanics
• /
• 제7권3호
• /
• pp.321-331
• /
• 2018

When a cantilever beam with a lumped mass at its free end undergoes free transverse vibration, internal axial forces are produced in the beam. Such internal axial forces have an effect on free transverse vibration of the beam. This effect is studied in this paper. The equations of motion for the beam in terms of the generalized coordinates including the effect are derived. The method for determining free transverse vibration of the beam including the effect is presented. In numerical simulations, the results of free transverse vibration of the free end of the beam including and not including the effect are obtained. Based on comparison between the results obtained, the conclusions concerning the effect are given.

• International Journal of Precision Engineering and Manufacturing
• /
• 제3권2호
• /
• pp.61-71
• /
• 2002

This paper presents the dynamic analysis of indeterminate rotor systems with angular contact ball bearings subject to axial and radial loads. The reaction forces against applied radial loads significantly influence the dynamic characteristics of angular contact ball bearings. However, the reaction forces are hard to determine in the case of indeterminate rotor-bearing systems. To this end, this paper proposes a finite element model for indeterminate rotor systems with angular contact ball bearings. An improved bearing model is adopted which is originated from the Harris's bearing dynamic model. The bearing model is also extended to include centrifugal forces due to the ball and inner ring. This paper utilizes a new iterative algorithm for general, indeterminate rotor systems with angular contact ball bearings. This examples are provided to illustrate the dynamic characteristics of rotor systems with angular contact ball bearings subject to axial and radial loads. The experimental and numerical results prove that the proposed method is useful for the dynamic analysis of indeterminate rotor systems with angular contact ball bearings.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 봄 학술발표회 논문집
• /
• pp.327-334
• /
• 1998

A method of calculating the natural frequency corresponding to the first mode of vibration of beams and toll.or structures, with irregular cross sections and with arbitrary boundary conditions was developed and reported by Kim, D. H. in 1974. In this paper, the result of application of this method to the special orthotropic plates with free edges supported on elastic foundation and with a pair of opposite edges under axial forces is presented. Such plates represent the concrete highway slab and hybrid composite pavement of bridges. The reinforced concrete slab can be assumed as a special orthotropic plate, as a close approximation. The highway slab is supported on elastic foundation, with free boundaries. Sometimes, the pair of edges perpendicular to the traffic direction may be subject to the axial forces. The plate is subject to the concentrated load/loads, in the form of traffic loads, or the test equipments. Any method nay be used to obtain the deflection influence surfaces needed for this vibration analysis. Finite difference method is used for this purpose, in this paper. The influence of the modulus of the foundation, the aspect ratio of the plate, and the magnitudes of the axial forces and the concentrated attached mass on the plate, on the natural frequency is thoroughly studied.

• 한국농공학회논문집
• /
• 제57권6호
• /
• pp.59-68
• /
• 2015

Traditional structure analysis method is based on numerical matrix analysis to use the geometries consisting of the structure. The characteristics require a lot of computer memories and computational time. To avoid these weaknesses, new approach to analyze truss structure was suggested by adopting topological load redistribution method. The axial forces to be not structurely analyzed yet against outside loads were redistributed by using nodal equation of equilibrium randomly at each node without constructing global matrix. However, this method could not calculate the axial forces if structure is statically indeterminate due to degree of many indeterminacies. Therefore, to apply the method suggested in this research, all redundancies of truss structure were replaced by unit loads. Each unit load could make the deformation of a whole structure, and a superposition method was finally adopted to solve the simultaneous equations. The axial forces and deflections agreed with the result of commercial software within the relative error of 1 %, whereas in the case that the axial forces are relatively very smaller than others, the relative errors were increased to 2 %. However, as the values were small enough not to be considered, it was practically useful as a structural analysis model. This model will be used for structural analysis of truss type of large structure such as agricultural farming facility.