• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.2
• /
• pp.190-200
• /
• 2017

In general, an assessment of the benefits and costs with regard to vehicle safety standards are validated before regulations are implemented. This paper performs this validation for the mandatory automobile safety devices requirement for new micro-mobility. The reviewed car safety standards involved the installation of seat belts, airbags, ABS, crash speed standards, and pedestrian warning system. The benefit was estimated as the cost of accident reduction due to the installation of vehicle safety standards. As a result, the safety belt showed a B / C of 4.0 or higher, and it was found that the seat belt should be installed from 2017. After the seatbelt regulation in 2017, the results of the scenarios with the airbag, ABS, crash speed of 40 km/h, and the pedestrian warning system showed B / C of 1.0 or more according to the year of regulation. This study can be useful as a tool in the decision-making process with regard to the timing and type of vehicle safety standards requirement of micro-mobility in the future.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.55-63
• /
• 2008

Fine blanking is a process of press shearing which makes it possible to produce the thick sheet metal of the finished surface and the close dimensional accuracy over the whole material thickness in the single blanking operation. In this paper, a plate holder of automotive seat recliner is manufactured by FCF(Flow Control Forming) method using the conventional mechanical press instead of the fine blanking press. Main processes for manufacturing of the plate holder by FCF method are embossing, half blanking and trimming processes. Optimal clearance, stripper force and counter force to increase the dimensional accuracy of the plate holder have been investigated by FE-analysis. As a result of FE-analysis, the clearance for both embossing and half blanking processes was -2%t and the forces of stripper and counter were 25ton and 15ton, respectively. After manufacturing the plate holder by FCF method, the measured dimensional characteristics have been compared with the required specifications as the final product. Although the dimensional accuracy of the plate holder manufactured by FCF method was a little inferior to that by fine blanking process, it was satisfactory in a general sense.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.6
• /
• pp.1-8
• /
• 2004

In this paper we present the effects that valve train design parameters and operating conditions have on the valve rotation properties of a diesel engine. Rotation of intake and exhaust valves are very closely related to the long term durability of diesel engines. of the valves do not rotate even at a rated engine speed, it causes the uneven wear of the valve seat and valve head contact area, which eventually shortens the engine life. Because the rated speed of a diesel engine is relatively lower than that of a gasoline engine, the operating condition of a diesel engine produces tough environment for valve rotation. Therefore, the valve rotation is an important problem which should be solved in the early stage of engine development. In this study, we developed a new technique to measure the valve rotation and shaking motion simultaneously using three proximity sensors. Valve train rotating properties of a diesel engine were measured under various engine operating conditions.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.4
• /
• pp.102-109
• /
• 2003

Safety and comfort are importance concepts for designers of vehicle seats and instrument panels. There have been a lot of researches on comfortable sitting postures, however, relatively a few researchers have tried to find a desirable driving posture in consideration of both comfort and safety. This study investigates a relationship between comfort and safety of sitting posture of a driver. Since a seat is closely related to comfort, the angular data of comfortable sitting posture were obtained through the correlation between the seat and the driver. In order to acquire the data of safe sitting posture, computer simulations were performed for various seatback angles. Based on comparing and analyzing the data obtained, the optimal sitting posture is suggested for both comfort and safety aspects.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.24 no.5
• /
• pp.588-595
• /
• 2016

This paper is a study on head bolts that are used in A/C compressors to reduce production cost and solve leak problems on the head bolt seat area that causes massive intermittent malfunctioning during production. In this study, the pre-heat treated steel, which was used as a material in the head bolt, eliminated the heat treatment process after forging. The pre-heat treated steel head bolts, which have 10 % lower tensile strength than the conventional SCM 435 head bolts, were selected after considering the results of creeping rupture properties, axial force, and stress concentration per tensile strength variation. Then, the performance test and the durability test with the A/C compressor that was assembled with the pre-heat treated steel head bolts were performed and verified. Based on the results, the pre-heat treated steel head bolts developed in this study saved 7.3 % in production cost by eliminating the heat treatment process and the logistics process. Furthermore, the leak problem on the head bolt seat area in the A/C compressor was addressed significantly on the mass production assembly line.

• International Journal of Automotive Technology
• /
• v.8 no.2
• /
• pp.185-191
• /
• 2007

The new FMVSS 208, 213, 225 regulations include automatic suppression of airbags to prevent low-risk airbag deployment and the use of child seats with a rigid-bar anchor system. The regulations mean that children must sit in the rear seat, but do not include other specific safety measures for their protection. In the rear, restraint equipment consists of three-point shoulder/lap belts for the outside seats and a static two-point lap belt in the middle, with no additional devices such as pretensioners or load limiters; this is far from optimal for children. This study investigated injury rates using a 3-year-old-child dummy. ECE R44 sled tests used a booster, a speed of 48 km/h, and a 26- to 32-g rectangular deceleration pulse. While seated on a booster, the dummies were restrained by an adult shoulder/lap three-point belt. HIC_15 msec, Chest G and Nij were somewhat lower with an emergency locking retractor (ELR)+pretensioner+load limiter than with only an ELR or with ELR+pretensioner. However, the current seat-belt system results in injury rates that exceed the limit for OOP performance under the new FMVSS 208 regulations.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.5
• /
• pp.525-533
• /
• 2022

In this study, in order to numerically analyze the heat flow characteristics in the valve according to the opening rate for the solenoid valve for hydrogen supply applied to the hydrogen storage tank, flow characteristics were comparatively analyzed. Through the analysis of pressure and temperature distributions within the valve according to the high-pressure supply condition of 70 MPa or more, the heat flow characteristics in the valve, inlet and outlet passage according to the opening rate of the valve were identified. As a result a sudden change in the fluid behavior appears in the neck region of the valve, and it is understood that the flow separation caused by the flow path shape of the expanded tube has a dominant influence on the flow characteristics. And, it was confirmed that the shape of the valve seat is a factor significantly affecting the improvement of flow rate and differential pressure performance.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.4
• /
• pp.345-351
• /
• 2003

Due to increasing legal and market demands for safety in the automotive design process, the design of integrated seat is important more and mote because it should satisfy the conflict between stronger and lower weight for safety and environmental demands. In this study for crash simulations, the numerical simulations have been carried out using the explicit finite element program LS-Dyna according to the FMVSS 210 standard for safety test of seat. Since crash simulations are very time-consuming and a series of simulations that does not lead to a better result is very costly, the optimization method must be both efficient and reliable. As a result of that, statistical approaches such as design of experiments and response surface model have been successfully implemented to reduce time-consuming LS-Dyna simulations and optimize the safety and environmental demands together with nonlinear optimization algorithm. Design of experiments is used lot exploring the design space of maximum displacement and total weight and for building response surface models in order to minimize the maximum displacement and total weight of integrated seat.

• Transactions of Materials Processing
• /
• v.20 no.3
• /
• pp.214-221
• /
• 2011

In recent years, automotive seat components have been manufactured by the fine blanking process, allowing an improvement of dimensional accuracy at sheared surface in series production. However, the rollover has increased and die failures have occurred more frequently when manufacturing gears by fine blanking. Consequently, important goals for manufacturing seat recliner parts with gears have been to decrease the rollover as well as to improve the tool life. In this study, the half blanking and shaving processes were introduced to improve aforementioned problems for the lower tooth, the main component of a seat recliner. For this purpose, the half blanking process was optimized using the finite element (FE) analysis and design of experiment (DOE). The optimized conditions resulting from this study were an offset of 0.2 mm, a clearance of 0.1 mm and a penetration depth of 4.5 mm. Fine blanking experiment conducted under the optimal condition resulted in a rollover depth decrease from 1.9 to 1.3 mm, and no die failure occurrence.

• Journal of Korean Institute of Industrial Engineers
• /
• v.39 no.2
• /
• pp.105-108
• /
• 2013

Drivers' sitting strategies are considered in car seat design. Existing research has identified representative sitting strategies by visual inspection of seating pressure measurements collected from a small sample size of drivers. The present study recruited 20 female and 20 male participants, measured seating pressure, and classified sitting strategies by cluster analysis. The participants' sitting postures were classified based on seating pressure distribution into mid-back and scapular, mid-back and lumbar, and lumbar sitting strategies for the upper body and hip concentrated, hip and mid-thigh concentrated, and hip and mid-thigh distributed sitting strategies for the lower body. The effects of gender and occupant package layout (OPL) on sitting strategy were nout found significant. The identified sitting strategies would be of use for the design and evaluation of an OPL and a seat.