• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.10a
• /
• pp.1-8
• /
• 2000

Automotive electronics as we know it today encompasses a wide variety of devices and systems. Key to them all, and those yet to come. is the ability to sense and measure accurately automotive control parameters. In other words, sensors and actuators are the heart of any automotive electronics application. The important of sensors and actuators cannot be overemphasized. The future growth of automotive electronics is arguably more dependent on sufficiently accurate and low-cost sensors and actuators than on computers, controls, displays, and other technologies. Without them, all of controls system - engine. transmission. cruise, braking, traction, suspension, steering, lighting, windshield wipers, air conditioner/hearter - would not be possible. Those controls, of course, are key to car operation and they have made cars over the years more drivable, safe, and reliable. In this lecture, the principle and future trends of electronic control gasoline engine will be discuss.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.196-206
• /
• 2000

These days, the fuzzy logic or the fuzzy set theory has received attention from a number of researchers in the area of industrial application. Moreover, the fuzzy logic control has been successfully applied to a large numbers of control problems where the conventional control methods had failed. Using this control theory we designed a climate controller for an automotive climate control system whose mathematical model is difficult. This paper describes an automotive climate control where the fuzzy control has been used to stabilize parameter uncertainties and disturbance effects. To show the validity and effectiveness of the proposed control method, the fuzzy logic controller was implemented with a philips 80C552 microcomputer chip and tested in an actual vehicle. From the experimental results, it could be conduced that the proposed controller is superior to conventional controllers in both control performance and thermal comfort. The climate control system in cars is difficult to model mathematically so we tested a fuzzy logic control system which promised better results.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.6 no.3
• /
• pp.139-148
• /
• 2011

As the architecture of automotive software is complicated and LOC of software increases, there is an increasing demand for standard operating system. OSEK/VDX defines an industry standard for automotive operating system and middleware. This paper introduces an implementation of RTOS(OSCAR-OSEK) based on OSEK/VDX standard. For better speed of scheduling, we suggest a new method for ready queue implementation considering the characteristic of automotive application software. Also we introduce a method for improving the portability of RTOS on various MCUs. And, we show OSCAR-OSEK implementation and performance test results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.25 no.1
• /
• pp.35-41
• /
• 2017

The use of engineering plastics in automotive components is increasing with the trend towards improving the car strength and reducing weight. Among the different choices of materials, engineering plastic emerged as the necessary material for achieving lower costs, reduced weight and improved production efficiency. To produce the automotive parts, it is important to predict defect and validation of injection molding prior to design. Injection molding analysis and structural analysis are widely applied as a part of the design process when developing automotive parts. Injection molding analysis, in particular, involves a highly complicated mechanism that requires deep knowledge of polymer properties as well as an analytic approach different from that used for a general isotropic material when the molded material is used as a structural material. This is because the parts made of polymer have pre-stress factors such as intrinsic deformation and residual stress. The most important factors for injection molded plastic products are injection molding condition and cavity design, taking into account ease of molding, mass production and application. Despite optimal injection molding conditions and cavity design, however, glass fiber orientation is critically linked to strength reduction. The application of injection molding and structural coupled analysis provides a low-cost solution for product molding and structural validation, all prior to the actual molding. The purpose of this study involves the validation, pre-study, and solution of defect in injection-molded polymer automotive parts using the simulation software for injection molding and structural coupled analysis. Finally, this thesis provides validation of an injection molding and structural coupled analytic mechanism that can demonstrate the effect of glass fiber orientation on mechanical strength. Design improvement ideas for the injection molded product of PPS (Poly Phenylene Sulfide)+40% glass fiber are also suggested.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.4
• /
• pp.33-38
• /
• 2012

Sandwich composite panel with high strength steel face can reduce the weight of the automotive structural parts. Unlike the parts in aerospace application, the automotive parts are made by the forming process for mass production. The CAE simulation can predict the failures caused by forces and deformation during the forming process. Since the material properties are very important factor for the simulation, we performed the tensile test to get the material properties. The inspections by the optical microscope at each strain level show the states of the polymer resin. The material properties measured by the tensile tests are used for the input data of simulation. The simulation predicts the forming process of the bumper back beam very exactly compared with the try out results.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.3
• /
• pp.127-141
• /
• 2009

While the ever-increasing complexity of automotive software systems can be effectively managed through the adoption of a reliable real-time operating system (RTOS), it may incur additional resource usage to a resultant system. Due to the mass production nature of the automotive industry, reducing physical resources used by automotive software is of the utmost importance for cost reduction. OSEK OS is an automotive real-time kernel standard specifically defined to address this issue. Thus, it is very important to develop and exploit kernel mechanisms such that they can achieve minimal resource usage in the OSEK OS implementation. In this paper, we analyze the task subsystem, resource subsystem, application mode and conformance classes of OSEK OS as well as the OSEK Implementation Language (OIL). Based on our analysis, we in turn devise and implement kernel mechanisms to minimize the dynamic memory usage of the OSEK OS implementation. Finally, we show that our mechanisms effectively reduce the memory usage of OSEK OS and applications.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.3
• /
• pp.68-74
• /
• 2014

As the number of ECUs (Electronic control units) are increasing, reliability and functional stability of a software in an ECU is getting more important. Therefore the application of functional safety standards ISO 26262 is making the software more reliable. Software fault injection test (SFIT) is required as a verification technique for the application of ISO 26262. In case of applying SFIT, an artificial error is injected to inspect the vulnerability of the system which is not easily detected during normal operation. In this paper, the basic concept of SFIT will be examined and the application of SIFT based on ISO26262 will be described.

• Journal of Welding and Joining
• /
• v.31 no.3
• /
• pp.49-53
• /
• 2013

Recently, studies about application of magnesium alloy sheet to automotive bodies are on the increase. For application to automotive bodies, researches about characteristics of resistance spot welding of magnesium alloy sheet are essential. Electrode life of resistance spot welding of magnesium alloy is very short due to sticking of magnesium alloy to copper alloy electrode. To increase electrode life, most effective method is inserting cover plate between electrode and magnesium sheet. But application of cover plate to actual process is difficult and decreases welding productivity. Process tape supplied automatically as cover plate can minimize lose of productivity and increase welding quality. In this study, resistance spot welding of magnesium alloy is carried out with applying process tape. Acceptable welding current region according to electrode force and welding time is determined.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.1 no.2
• /
• pp.89-102
• /
• 1993

In this experimental investigation, various plasma-sprayed zirconia contained coatings and a kind of alumina-zirconia coating were studied to gain a better understanding of their tribological behaviour under dry contact condition in a reciprocating motion at temperature of 200℃. Particular attention was made for finding appropriate coatings in cylinder liner/piston ring application with an emphasis on the antiwear property. In order to identify the wear mechanism, SEM(Scanning Electron Microscope), optical micrograph, and roughness tester were used. Alumina-zirconia and 8% yttria-zirconia were found to be most appropriate for the application to the cylinder liner/piston ring and, especially, alumina-zirconia exhibited highest wear-resistance and also showed good friction characteristics. Wear mechanisms of ceramic coatings identified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.2
• /
• pp.175-181
• /
• 2007

The objective of this study was to develop formability evaluation techniques in order to apply aluminum sandwich panel for automotive body parts. For this purpose, newly adopting formability evaluation (using limit dome height and plane strain test) was carried out in order to secure the fundamental data for the measurement of sheet metal forming and the establishment of optimum forming conditions of the aluminum sandwich panel. The results showed that there were good agreements between the old formability evaluation method and the new method which was more simplified than that of old one. From the results of these formability evaluation, the formability of sandwich panel was higher than that of aluminum alloy sheet alone which was the skin component for the sandwich panel. Also, it was found that sandwich panel could reduce the weight and could have the same flexural rigidity simultaneously when it was compared to the automotive steel sheet.