• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.4
• /
• pp.166-174
• /
• 2002

Power steering systems far automobile are becoming ever more popular because they reduce steering efforts of the drivers, especially during parking lot maneuver. In this paper, the controller of the motor driven hydraulic power steering(MDHPS) has been designed and developed. This system uses a power source of DC motor instead of engine power source for power steering drive oil pump. The developed MDHPS system is accomplished a highly sensitive power steering resulted from electronic control under variable driving condition. Furthermore, this system is more improvement than type of engine driving far fuel economy.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.759-762
• /
• 2002

Automobile aeroacoustics Is a developing area of technology where experimental and theoretical tools are being continuously refined to understand, analyze and modify the noise-generating mechanisms in the vehicle flow. Main sources of ground vehicle exterior noise are the tires (tire/road interaction) and the unsteady flow field around the vehicle. In this study, the sound source localization of a rolling tire was applied to the measurement of radiated sound by using an acoustic mirror system. A possible flow pattern that develops is suggested based on detailed wind tunnel investigations with a rotating wheel in contact with a moving belt.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.4 no.3
• /
• pp.40-49
• /
• 1996

With the advance of the standard of living, the demand on automobile goes beyond the simple transportion equipment, therefore the interior noise reduction has been the important factor for improvement of the ride quality. Idling noise is a major vehicle characteristic determining occupant comfort. In the present research two approaches for noise source identification based on theory for multi-input system have been investigated. The concept of the frequency response function and the multi-dimensional spectral analysis were used to estimated the spectra of the noise source.

• Current Optics and Photonics
• /
• v.1 no.3
• /
• pp.207-213
• /
• 2017

The Adaptive Front-lighting System (AFS) is a part of the active safety system, providing optimized vision to the driver during night time and other poor-sight conditions of the road by automatic adaptation of lighting to environmental and traffic conditions. Basically, an AFS provides four different modes of the passing beam as designated in an United Nations Economic Commission for Europe regulation (ECE324-R123): neutral state or country light (Class C), urban light (Class V), highway light (Class E), and adverse weather light (Class W). In this paper, we first present an optics design for an AFS system capable of producing the Class C/V/E/W patterns requiring only on/off modulation of multi-array LEDs with no need for any additional mechanical components. The AFS optics consists of two separated modules, cutoff and spread; the cutoff module lights a narrow central area with high luminous intensity, satisfying the cutoff regulation, and the spread module forms a wide spread beam of low luminous intensity. Each module consists of two major parts; the first converts a discretely positioned LED array into a full-filled area emitting light source plane, and the second projects the light source plane to a 25 m away target plane. With the combination of these two optics modules, the four beam patterns are formed by simple on/off modulation of multi-array LEDs. Then we report the development of a prototype that was demonstrated to provide the four beam patterns.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.6
• /
• pp.534-542
• /
• 2003

Small electric motors in an automobile perform various tasks such as engine cooling, pumping, HVAC etc. At present, most of them are DC motors supplied by 12V or 24V batteries. However, DC motors suffer from low efficiency, life cycles and reliability. Therefore, there is a growing interest in substituting DC motors for advanced at motors including switched reluctance motors(SRM). Although there are several other forms SRM convertors, they are either unsatisfactory to the control performance or unsuitable for the 12V battery source. Especially, a conventional asymmetric converter of SRM provides the best flexible and effective control to the current waveform of SRM, but it has the most switches and produces conducting voltage drops across two power switches during SRM operation. For automotive applications with a 12V battery source, this circuit is inadequate. For considering the requirement for effective operation and simple structure of converter in the limited internal circumstance of automobiles, the author inclines toward selecting Modified C-dump converter and Energy efficient c-dump converter.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.7
• /
• pp.51-57
• /
• 2009

In this paper, we studied on an attenuation effect of automobile exhaust noise according to the direction of canceling speaker in duct-acoustic ANC system. Automobile exhaust noise was recorded at 800rpm, 3500rpm and 5000rpm of a diesel engine. Directions of canceling speaker can be set to $30^{\circ}$, $90^{\circ}$ and $150^{\circ}$ against the primary noise flow by acrylic ducts to be made for the experimentation. DSP board used to control the ANC system. The algorithm of this ANC system applied the Filtered-x-LMS algorithm that is modified to compensate for a property of DSP input signal and the secondary-path effect. As an experiment result, the direction of canceling speaker was proved to influence the reduction effect of noise. The $150^{\circ}$ duct in the attenuation effect of noise showed a better result than the $90^{\circ}$ or $30^{\circ}$ duct.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.11
• /
• pp.1630-1636
• /
• 2003

Automobile companies and research institutions in leading automobile-manufacturing nations have recently been very active with research regarding the HCCI engine for use in future vehicles. Because HCCI engines take advantage of high compression ratio and heat release rate, they exhibit high efficiency found in compression ignition engines. HCCI engines also utilize a lean air/fuel ratio resulting in low emissions of NO$_{x}$ and PM (particulate matter). The objective of this research is to determine the effects of EGR rate on the combustion processes of HCCI. for this purpose, a 4-cylinder, compression ignition engine was converted into a HCCI engine, and a heating device was installed to raise the temperature of the intake air and also to make it more consistent. In addition, a pressure sensor was inserted into each of the cylinders to investigate the differences in characteristics among the cylinders. The experimental study of the effects of EGR rate on various gas emissions, engine performance, etc. should prove to be a valuable source of information for the development of the HCCI engine.e.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.16 no.3
• /
• pp.276-283
• /
• 2006

Work-related musculoskeletal disorders (WMSDs) were a major source of disability and lost work time after 'Foreign Currency Crisis(1998-2000)' in Korea. There is considerable evidence documenting the association between psychosocial risk factors and work disability due to WMSDs. But, there is not much in Korea. The present study aimed to explore the predictive association between the changed working conditions and WMSDs after 'Foreign Currency Crisis' in Korea. A study sample of 8,670 automobile assembly workers were recruited for this study. A structured-questionnaire was used to assess general characteristics, working conditions, and information concerning medical treatment of WMSDs. After adjustment for sociodemographic factors, increased overtime work(OR=1.22), daily work time(OR=1.20), work speed (OR=1.32), number of workers(OR=0.83), supervisory control(OR=1.39), physical load(OR=1.39), and mental load (OR=1.25) were all founded to be significantly associated with WMSDs. This study has shown the importance of changed working conditions in the occurrence of WMSDs. Therefore, it will be necessary to reduce WMSDs with controlling both physical and psychosocial factors.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.170-175
• /
• 2016

An internal combustion engine is the most widely used power source for an automobile. In order to resolve environmental problems resulting from the use of internal combustion engines, environmentally friendly automobiles such as hybrid, electric, and air-engine vehicles are being developed. The share of hybrid vehicles using battery or pure electric vehicles, which are not popular, is gradually increasing. Compared to an electric vehicle, which uses an electric motor, air-engine vehicles, which use compressed air, have hardly been developed. In this study, a compressed air engine with a scroll expander is introduced, and the potential mileage of an automobile utilizing this engine is theoretically calculated.

• 제어로봇시스템학회:학술대회논문집
• /
• 1998.10a
• /
• pp.474-479
• /
• 1998

In this paper, we present a mathematical model of the piezoelectric pump and its application to the automobile brake system. The piezoelectric pump consists of a multi-layered piezoelectric element a diaphragm, pumping values, resonant pipes and accumulators, and the maximum pumping power of 62W nab obtained in the previous experiments by using the piezoelectric element of 22mm diameter and 55.5mm length. A detailed mathematical model of the pump is derived here by considering the compressibility of the working oil, nonlinear characteristics of piezoelectric element, the time delay of pumping values' action and be on. The validity of the model is illustrated by comparing the experimental data and the simulation results. Using the mathematical model of the piezoelectric pump, a brake system for automobile disk brake is also simulated in this paper. The brake system consists of a piezoelectric pump as a power source, calipers and its piston to generate brake force, and a three position solenoid value to change the brake situation. It is shown that 15mm/sec of piston speed and 20kN of piston force are obtained by using the piezoelectric element of 33mm diameter and 55.5mm length.