• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.176-179
• /
• 2005

To control the vibration transmitted to the precision instruments from ground has always been of great interest among the researchers. This paper proposes a single axis vibration isolation system which can be used as a module far a table top six axis isolator for highly precise measurement and actuation system. The combined active-passive isolation principle is used for vertical vibration isolation by mounting the instrument on a passively damped isolation system made of Elastomer along with the active stage in series which consists of very stiff piezo actuator. The active stage works in combination with the passive stage for working as a very low frequency vibration attenuator. The active stage is isolated from the payload disturbance through the Passive stage and thus modularity in control is achieved. This made the control algorithm much easier as it does not need to be tuned to specific payload.

• Journal of the Optical Society of Korea
• /
• v.7 no.2
• /
• pp.72-78
• /
• 2003

It is reported that the spectral loss of photonic crystal fiber (PCF) having a large hole-to-hole distance (~ 10 ${\mu}{\textrm}{m}$) is sensitive to micro- and macrobending when compared with the conventional single-mode fiber. In this paper, we will present the measurement result of the macro- and microbending characteristics of fabricated PCF with large hole-to-hole distance (> 10 ${\mu}{\textrm}{m}$) . For the macrobending experiment, the fiber was simply wound around a circular structure with variable diameter that could be reduced to a few centimeters. For the microbending case, regularly spaced silica rods were attached on a slide glass and pressed against the fiber by loading a stack of metal plates of known weight on the glass. The transmission loss spectrum shows a rather flat response to the to microbending, and this makes the PCF a good candidate for a wideband variable optical attenuator.

• Wind and Structures
• /
• v.32 no.1
• /
• pp.71-80
• /
• 2021

In steel cable bridges, the use of magnetorheological (MR) dampers between butt cables is constantly increasing to dampen vibrations caused by rain and wind. The biggest problem in the actual applications of those devices is to launch a kind of appropriate algorithm that can effectively and efficiently suppress the perturbation of the tie through basic calculations and optimal solutions. This article discusses the optimal evolutionary design based on a linear and quadratic regulator (hereafter LQR) to lessen the perturbation of the bridges with cables. The control numerical algorithms are expected to effectively and efficiently decrease the possible risks of the structural response in amplification owing to the feedback force in the direction of the MR attenuator. In addition, these numerical algorithms approximate those optimal linear quadratic regulator control forces through the corresponding damping and stiffness, which significantly lessens the work of calculating the significant and optimal control forces. Therefore, it has been shown that it plays an important and significant role in the practical application design of semiactive MR control power systems. In the present proposed novel evolutionary parallel distributed compensator scheme, the vibrational control problem with a simulated demonstration is used to evaluate the numerical algorithmic performance and effectiveness. The results show that these semiactive MR control numerical algorithms which are present proposed in the present paper has better performance than the optimal and the passive control, which is almost reaching the levels of linear quadratic regulator controls with minimal feedback requirements.

• ETRI Journal
• /
• v.42 no.6
• /
• pp.837-845
• /
• 2020

The objective of this study was to implement an in vitro exposure system for 28 GHz to investigate the biological effects of fifth-generation (5G) communication. A signal source of 28 GHz for 5G millimeter-wave (MMW) deployment was developed, followed by a variable attenuator for antenna input power control. A power amplifier was also customized to ensure a maximum output power of 10 W for high-power 28-GHz exposure. A 3-dB uniformity over the 80 mm × 80 mm area that corresponds to four Petri dishes of three-dimensional cell cultures can be obtained using a customized choke-ring-type antenna. An infrared camera is employed for temperature regulation during exposure by adjusting the airflow cooling rate via real-time feedback to the incubator. The reported measurement results confirm that the input power control, uniformity, and temperature regulation for 28-GHz exposure were successfully accomplished, indicating the possibility of a wide application of the implemented in vitro exposure system in the fields of various MMW dose-response studies.

• Nuclear Engineering and Technology
• /
• v.54 no.1
• /
• pp.283-292
• /
• 2022

Advanced radiation applications have been widely used and extended to many fields. As a result of this fact, choosing an appropriate shielding material based on the radiation application has become vital. In this regard, the integration of elements into polymer composites has been investigated and contributed to the quantity and quality of radiation shielding materials. This study reports photon attenuation parameters and electromagnetic shielding effectiveness of a novel polymer composite prepared with a matrix reinforced with three different proportions (5, 10, and 15 wt%) of niobium content. Addition of Nb dopant improves both photon attenuation and electromagnetic shielding effectiveness for the investigated composites. Therefore, Nb(15%) polymer composite with highest concentration has been found to be the best absorber for ionizing and non-ionizing radiations. Consequently, the performed analyzes provide evidences that the prepared Nb-reinforced polymer composite could be effectively used as photon radiation attenuator and electromagnetic shielding material.

• Nuclear Engineering and Technology
• /
• v.56 no.7
• /
• pp.2437-2443
• /
• 2024

This work synthesized four glass samples with a fixed ratio of PbO to Na₂O and a variable ratio of BaO to B₂O₃. The linear attenuation coefficient (LAC) (μ, cm^-1) and additional attenuator parameters were determined experimentally using a semiconductor detector and different gamma sources. The comparison was carried out between the experimental and the XCOM calculated results, with good agreement emerging between the two results. The impacts of the BaO substituting for the B₂O₃ on fabricated PNBB glasses' radiation shielding properties were discussed. By increasing the BaO substitution concentration between 10 and 25 mol.%, the LAC μ values (cm^-1) increased by 76.60 %, 13.81 %, 12.56 %, and 12.52 % for the respective γ-ray energies of 0.059, 0.662, 1.173, and 1.332 MeV. The μ value reduction with raised gamma energy values increased the values of the calculated half-value thickness (Δ_0.5) as a result of the μ and Δ_0.5 values' reverse proportionality. Other shielding parameters such as the lead equivalent thickness (Δ_eq) and radiation protection efficiency were also determined for the present PNBB glass samples.

• Aerospace Engineering and Technology
• /
• v.7 no.2
• /
• pp.176-186
• /
• 2008

As determined single coaxial cable for the interface between satellite and ground station in COMS RF compatibility test, RF supporting unit was required to allow signals in different frequency-band to be exchanged in the single coaxial cable. In addition, the path loss between satellite and ground station in normal operation should be simulated through two RF supporting units connected to the ends of single coaxial cable. As an effort to design RF supporting unit, level diagram was firstly conducted on the basis of measured data for each element. From the level diagram, it was found that single coaxial cable connected with two RF supporting units properly represented the path loss between satellite and ground station After RF supporting unit was integrated on aluminum plate, it was tested that input signal level at each test cap linked with MODCS and TC&R was tunable within the required dynamic range. RF supporting unit, now completely integrated, will be applied in the upcoming COMS RF compatibility test.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.2
• /
• pp.119-126
• /
• 2015

The information about noise parameters is essential in the design of low noise amplifier. In the past, the noise parameters were measured using an impedance tuner and noise figure analyzer. Recently, the authors proposed the method of measuring the noise parameters using the 8-port network without the aid of the mechanically driven impedance tuner. However, the 8-port method still requires the noise source and causes the complexity in the measurements. In this paper, a novel measurement method of the noise parameters without the noise source using 6-port network is proposed. Based on the proposed 6-port method, the noise parameters of 10 dB attenuator whose noise parameters can be theoretically determined were measured and the measured noise parameters are compared with those measured using the previous 8-port network method. As a result, the accuracy of the measured noise parameters using 6-port network is found to be comparable to the previous 8-port network method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1243-1251
• /
• 2009

This paper presents design and test results of X-Band Transmit/Receive(T/R) module for active phased-array radar. Active phased array radars typically require solid state T/R modules with high output power, low noise figure, high Third Order Intercept(TOI), and sufficient gain in both transmit and receive. The output power of the module is 9 watts over a wide bandwidth. The noise figure is as low as 2.8 dB. Phase and amplitude are controlled by the 6-bit phase shifter and 5-bit attenuator, respectively. Highly integrated T/R module is achieved by using LTCC(Low Temperature Co-fired Ceramic) multiple layer substrate. The module incorporates a compact digital interface, requires only three supply voltages.

• Journal of Satellite, Information and Communications
• /
• v.1 no.2
• /
• pp.56-62
• /
• 2006

This paper describes the MMIC product qualification of the Ka band satellite transponder for the COMS(Communication, Ocean and Meteorological Satellite). Ka-band active equipment for the COMS communications transponder are being developed by using 12 kinds of MMICs which include low noise amplifiers, medium power amplifiers, frequency mixers, frequency multipliers, RF switch, and HEMT attenuator MMIC, Those MMICs had been fabricated at the MMIC production foundry of northrop Grumman Space Technology (Velocium) which is qualified for space application, and experienced in various space programs during past decades. For the MMIC product qualification, Visual inspection and SEM inspection had been performed, and burn-in test for 240 hours and accelerated life-test for 1000 hours had been done on test fixtures of individual MMIC products at $125^{\circ}C$. Additionally, infrared temperature scanning and finite element simulation were performed to analyze and confirm the channel temperature of semiconductor devices on several representatives of those MMIC products that os one of the most important factors in performance degradation and life reduction.