• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.114-122
• /
• 2012

Vertical closed-loop ground source heat pump systems(GSHP) have been installed widely in Korea since it can extract moderate temperature level of geothermal heat in a small area. As a ground heat exchanger, a vertical closed -loop type with brine circulation is mostly preferred since it is simple and less harmful to ground environment. However, it requires a secondary heat exchange loop between the refrigerant in a heat pump and the brine. By adding a geothermal heat exchanger in the secondary heat exchange loop, circulation pumps should be attached and the temperature difference between refrigerant and ground is increased, which are important parts of performance degradation. In this paper, annual and seasonal performances of direct expansion(DX) geothermal heat pump were estimated mathematically as an alternative of classical indirect geothermal heat pump based on the annual performance evaluation. As results, DX geothermal heat pump showed 43% higher annual performance than the classical U-tube geothermal heat pump.

• Journal of the Korean Solar Energy Society
• /
• v.32 no.3
• /
• pp.11-18
• /
• 2012

To expect accurately the maximum power of solar cell module under various installation conditions, it is required to know the performance characteristics like temperature dependence. Today, the PV (photovoltaic) market in Korea has been growing. Also BIPV (building integrated photovoltaic) systems are diversified and become popular. But thermal dependence of PV module is little known to customers and system installers. In IEC 61215,a regulation for testing the crystalline silicon solar cell module, the testing method is specified for modules. However there is limitation for testing the module with diverse application examples. In extreme installation method, there is no air flow between rear side of module and ambient, and it can induce temperature increase. In this paper, we studied the roof type installation of PV module on the surface of one-axis tracker system. We measured temperature on every component of PV module and compared to open-rack structure. As a result, we provide the foundation that explains temperature characteristics and NOCT (nominal operation cell temperature) difference. The detail description will be specified as the following paper.

• Nuclear Engineering and Technology
• /
• v.34 no.5
• /
• pp.468-481
• /
• 2002

There are 4 CANDU6 type reactors operating at Wolsong site. For fuelling operation of certain fuel channels (with flow less than 21.5 kg/s) a FARE flow Assist Ram Extension) device is used. During the refuelling operation, two remote controlled F/Ms (Fuelling Machines) are attached to a designated fuel channel and carry out refuelling job. The upstream F/M inserts new fuel bundles into the fuel channel while the downstream F/M discharges spent fuel bundles. In order to assist fuelling operation of channels that has lower coolant How rate, the FARE device is used instead of F/M C-ram to push the fuel bundle string. The FARE device is essentially a How restricting element that produces enough drag force to push the fuel bundle string toward downstream F/M. Channels that require the use of FARE device for refuelling are located along the outside perimeter of reactor. This paper presents the FARE device design feature, steady state hydraulic and operational characteristics and behavior of the device when coupled with fuel bundle string during fuelling operation. The study showed that the steady state performance of FARE device meets the design objective that was confirmed by downstream F/M C-ram force to be positive.

• Applied Chemistry for Engineering
• /
• v.3 no.1
• /
• pp.72-80
• /
• 1992

Group 6 $M(CO)_4$(2, 2'-bipyridine)[M=Cr, Mo, W] was synthesized by substituting CO ligand of $M(CO)_6$ with strong electron donating ligand, 2, 2'-blpyridine, in the presence of phase transfer catalyst. The effective of catalyst and solvent on the product yield were discussed according to concentration and kinds of catalyst, kinds of center cation and anion, type of alkyl and aryl groups attached to the center cation, and different chain length.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.5
• /
• pp.385-393
• /
• 2004

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(voice coil motor) for coarse motion, for an SFF ODD(small form factor optical disk drive), in order to achieve fast access speed and precise track-following control. Over the past few decades there have been a lot of researches related to the VCM and dual-stage actuator. In this paper, we focus our attention on the design and control of the PZT actuator. Due to the dual cantilever structure. the PZT actuator can generate precise translational tracking motion at its tip to which an optical pickup is attached. and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing it with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.351-351
• /
• 2004

For greeting the era of ubiquitous network, data storage devices have been essentially attached to mobile data devices. As a result, the minimization of the storage device has arisen as major interests in the next generation data storage technology. So, there are many researches for the small form factor ODD. In this paper, we propose a pick up that consists of a linear VCM and 2-wire focusing actuator for a small form factor ODD. For the sake of checking performance of the coarse actuator, PID controller is designed. Experiment with controller and DSP board shows its propriety as a fine tracking actuator. And, 2-wire suspension actuator is designed in order to be contained in a coarse actuator and to satisfy the thickness of a PCMCIA type. Through the experiment of designed actuator, It verifies performance as a focusing actuator.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.3
• /
• pp.39-45
• /
• 2002

A simple and low cost stylus profiler made of ferrite cores is developed. The devised profiler consists of a contact probe, a measuring transducer, a signal processing unit, and a motorized stage. The contact probe attached to 4-bar spring maintains sufficient stiffness to protect disturbances. An overlap-area type inductive position sensing system is selected as a measuring transducer, which has high sensitivity, repeatability and linearity. The transducer is composed of coil bundles and ferrite cores which have good electromagnetic characteristics in spite of low cost. The repeatability of the profiler with the proposed inductive sensing system is better than 50nm. Experimental results are shown that the proposed profiler can measure the line or 3D profile of an object with sub-micron features.

• Journal of the Korean Society of Physical Medicine
• /
• v.9 no.3
• /
• pp.271-278
• /
• 2014

PURPOSE: This study researched the effects of different types of high heels on the muscles surrounding the cervical spine, the thoracic spine, and the lumbar spine by analyzing muscle activation of the paraspinal muscles during walking while wearing high heels. The high heels were all of the same height: 8cm. METHODS: The 28 subjects in this experiment were females in their 20s with a foot size of 225-230mm. To measure the muscle activation of the paraspinal muscles, EMG electrodes were attached on the paraspinal muscles around C6, T7, and L5. The muscle activation during walking while wearing 8cm high wedge heels, setback heels, and french heels was measured. The measurements were performed 3 times each and the mean value of the result was used for analysis. Two kinds of velocity were used in this study. One of the velocity was 2.5 m/s. The other was 3.5 m/s. RESULTS: The muscle activation of paraspinal muscles increased significantly according to increase of walking velocity. But there was no significant difference according to the heel types. CONCLUSION: In view of the results, the height of heels and the velocity of walking are more convincing variables than the width of the heels on the muscle activation of paraspinal muscles. So wearing high heels is not recommended for those who have pain or functional problem of cervical and lumbar vertebrae.

• Journal of Agricultural Extension & Community Development
• /
• v.24 no.2
• /
• pp.83-97
• /
• 2017

The purpose of this study was to classify the type of customer which is essential to agricultural extension service, specify their needs and identify the performance level of public agricultural extension organization by the needs of customer. To meet these purpose, we conducted a focus group interview and surveyed the agricultural extension workforce. The results of this study are as follows. First, we classify the customer of agricultural extension service as 9 types. Second, the needs by customer types are specified 12 types. Third, those who attached to Rural agricultural development administration and agricultural research and extension service organization in provinces recognize them selves as more performing organization than agricultural technology center in region, except one area.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.450-453
• /
• 2003

In this paper, the miniaturization of linear polarization microstrip patch antenna is studied by attached Irises near the square linear polarization microstrip patch antenna which are induced the increase of current path. Microstrip patch antenna having the Irises is designed and fabricated at the resonant frequency of 1.575 GHz. The result is like that the resonant length of patch is reduced 41.5 mm which correspond to 50.9 % of that of plane type(81.5mm). The return loss is -28.5 dBd and -10 dB bandwidth is 103 MHz( 6.5 %). And as the radiation pattern is broad through the size reduction of patch, the gain is 5.9 dBd and -3 dB beamwidth of E-plane is $111.9^{\circ}$.