Journal of the Korea institute for structural maintenance and inspection
/
v.18
no.3
/
pp.93-100
/
2014
This study presents the recomposition of MBM (measurement-based model) using natural frequencies and modes from the usually measured data, and the evaluation of cable tension in service from the analysis results upon MBM of existing CSB (cable stayed bridge). The cable tension is shown to be different according to the position attached to cable and loading type. The measured cable tensions are not different distinctly according to position attached cable under dead and live loads, but larger than those under design loads. The distribution of cable tension calculated upon the MBM is similar to those of measured tension although the former is more than those of cable tension upon the design model. Considering to long-term behaviors of cable, therefore, the design of cable in CSB needs to apply the analysis results on MBM. For this purpose, future study needs lots of measured data and MBM is used to analyze the long-term behavior of cable in CSB.
The liquid phase LPG injection (LPLI) system (the third generation technology) has been considered as one of the next generation fuel supply systems for LPG vehicles, since it has a very strong potential to accomplish the higher power, higher efficiency, and lower emission characteristics than the mixer type(the second generation technology) fuel supply system However. when a liquid LPG fuel is injected into the inlet duct of an engine, a large quantity of heat is extracted due to evaporation of fuel. This leads to freezing of the moisture in the air around the outlet of a nozzle, which is called icing phenomenon. It may cause damage to the outlet nozzle of an injector or inlet valve seat. In this work, the experimental investigation of the icing phenomenon was carried out The results showed that the icing phenomenon and process were mainly affected by humidity of inlet air instead of air temperature in the inlet duel. Also, it was observed that the total ice formed around the nozzle weighs at about $150mg{\sim}260mg$ after injection for ten minutes. And some fuel species were found in the ice attached at the front side of a nozzle, while frozen ice attached at the back of a nozzle was mostly' consisted of moisture of inlet air. Therefore, some frozen ice deposit. detached from front nozzle of an injector, may cause a problem of unfavorable air fuel ratio control in the small LPLI engine.
Journal of The Korean Association For Science Education
/
v.5
no.1
/
pp.63-79
/
1985
The purpose of our survey study was to investigate the status on perception and actual state toward science educational evaluation and objectives of middle school science teachers in Pusan. The perception and actual state were surveyed by the questionaire which was developed by Jong-Ok Woo et. al. We developed two kinds of questionaire. One is designed to use Likert type scale and is composed of two main category(SE; Science educational evaluation, SO; Science educational objectives) which contains 21 question items, and the other has 16 question items From 313 science teacger's responses of 75 middle schools in pusan, the tendency. of total(SE+SO) and each sub category, and the contrast with their background and actual state were analized by SPSS program of KAIST. Some results of our survey study can be summarized as follows; 1. Total tendency of science educational evaluation(SE) and objectives(SO) of middle school science teachers in pusan shows a positive and right tendency of conception in general(m-85.8/100). 2. Tendency of SE(m-87.8/100) are slightly higher than SO(m-81.7/100). At the level of 5% significance, there are correlated but shows low correlation (r=0.12(4). 3. In each correlation toward total tendency(SE+SO), SE is highly correlated(r-0.8486) but SO is moderately correlated(r=0.6297) at the level of 0.1% significance. 4. Tendencies of 5sub category (PE, PC, PD, PO, PB) shows considerably right tendencies (m=$73.4/100{\sim}92.7/100$), there are moderately correlated foward total tendency(SE+SO) at the level of 0.1% significance (r=$0.49{\sim}0.60$). 5. At the level of 5%significance, total means are no differences which their background(Sex, Final alma mate, Major, Difference of training), but there is differences to teaching career at the level of 5% significance.
It was demonstrated that Transactivating transcriptional activator(TAT) protein from HIV-1 shown to enter cells when added to the surrounding media. TAT peptide chemically attached to various proteins was able to deliver these proteins to various cell and even in tissues in mice with high levels in heart and spleen. In this study, the tripeptide GKH(Glycine-Lysine-Histidine) derived from Parathyroid hormone (PTH), which was known as lipolytic peptide, is attached to 9-poly Lysine(TAT) to be used as a cosmetic ingredient for slimming products. When Glycerol release, expressed as extracellular glycerol concentration, is lipolysis index, TAT-GKH at $10^{-5}$mo1/L induces approximately 41.5% maximal lipolytic effects in epididymal adipocytes isolated from rats, compared with basal lipolysis. Epididymal adipose tissues of male rats is assessed ex vivo by microdialysis. Probes are perfused with Ringer solution in which increasing concentrations of TAT-GKH. The perfusion of TAT-GKH induces lipolytic effect. Penetration study showed that TAT-GKH efficiently elevates 36 times higher penetration into the excised hairless mice skin than GKH. in vivo study showed that TAT-GKH had a better effect upon the relative volume of eye bag after 28 days of application on twenty(+2) healthy female volunteers. It was identified that TAT-GKH increases penetration enhancement and lipolytic effects in both in vitro, ex vivo and in vivo.
Journal of the Korea Academia-Industrial cooperation Society
/
v.16
no.11
/
pp.7629-7634
/
2015
The purpose of this study is is to organize the site-plan types of common design's Goon office buildings in Japanese colonial period based on the main building's shape and main & attached building connection way and to investigate all the types' addition & remodeling ways. The study used literature research method, analysing the digital images, the annotation of the images, official documents between the Japanese government-general of Korea and To, and articles of newspapers or journals. The site-plans are sorted 5 types and subdivided 13 as their addition & remodelling ways. The initial shapes of site-plan were changed to apply every Goon's site circumstances, The main buildings were always in the center ahead and attached buildings behind or next to them in any cases of new construction, addition or remodeling. The buildings of the common design's were constructed until early 1930s and it means that their architectural level was lower than Pu office buildings, although both had same administrational level.
Kang, K. C.;Kim, Y. J.;Ryou, Y. S.;Baek, Y.;Rhee, K. J.
Journal of Biosystems Engineering
/
v.26
no.5
/
pp.441-448
/
2001
Hot air heater with light oil combustion is used as the most common heater for greenhouse heating in the winter season. However, exhaust gas heat discharged to atmosphere through chimney reaches up to 10~20% of total heat capacity of the oil burred. In order to recover the heat of this exhaust gas and to use for greenhouse heating, the heat pipe type exhaust heat recovery system was manufactured and tested in this experiment. The system consisted of a heat exchanger made of heat pipes, ø15.88${\times}$600mm located in the rectangular box of 675(L)${\times}$425(W)${\times}$370(H)mm, an air suction fan and air ducts. The number of heat pipe was 60, calculated considering the heat exchange amount between exhaust gas and air and heat transfer capacity of a heat pipe. The working fluid of heat pipe was acetone because acetone is known for its excellent heat transfer capacity. The system was attached to the exhaust gas path. According to the performance test it could recover 53,809 to 74,613kJ/h depending on the inlet air temperature of 12 to -12˚at air flow rate of 1.100㎥/h. The temperature of the exhaust gas left the heat exchanger dropped to 100$^{\circ}C$ from 270$^{\circ}C$ after the heat exchange between the suction air and the exhaust gas.
Park, Won-Yeop;Hong, Sung-Ha;Lee, Jae Min;Lee, Sang-Sik
The Journal of Korea Institute of Information, Electronics, and Communication Technology
/
v.8
no.3
/
pp.229-238
/
2015
This study was conducted to develop electronic control system of weeding implement that can operated at various areas such as slope land and inclined road side. The weeding implement consists of five main parts; the electronic control system, the hydraulic system, the main frame, the boom and arm mechanism, and the rotary type weeder. And the weeding implement was developed to be attached by three-point hitch of tractor considering the use of electronic control system. As a result, the electronic control test was conducted with the weeding implement attached to tractor in slope land. The results of the electronic control system test showed satisfactory weeding performance.
Journal of the Korean Institute of Landscape Architecture
/
v.13
no.1
/
pp.1-24
/
1985
The pinus trees planted by the road in the Seoul -Suwen high-way was surveyed on the damages due to air pollution during April and May in 1984. The results were as follows ; The concentration of SO$_2$was ranged from 0.003 to 0.05ppm, NOx from 0.03 to 0.1ppm and the amount of dust fall, from 10 to 110ton/km$^2$/month. While the concentrations of gaseous pollutants such as SO$_2$and NOx were notsignificantly different in the type of road and with in the distence of 20 meters from the road the dust falls were decreased as remoted from the road. The tissue damages of leaves were determined by the microscopic observation. The higher concentration of dust fall on the leaf, the more severe damage observed in the stomata. The attached dust of the leaves were ranged from 1l to 75mg/g of leaf, and those were significantly incereased as near from road. The sulfur contents of leaves were measured at 0.15g/100g of leaf in the 5 meters located and at 0.064g/100g of leaf in the 20 meters, and the lead contents, 45ug/g of leaf in the 5 meters and 24ug/g in the 15 meters. The appearent damages of plant were very much corelated to the attached dusts of leaves the sulfur contents and the amount of dust fall, and the multiple regression analysis between the damages and factors of air pollution were under taken. As increment of vehicle in future, the air Pollution was predicted and the plant damages were estimated.
The purpose of this study was to compare differences between essential tasks and delegable tasks among public kindergarten dietitians. A survey study was conducted through a self-administered online method from November 18 to December 28, 2019. The survey consisted of essential tasks and delegable tasks, including 6 Duties, 25 Tasks, and 94 Task Elements. The survey was distributed to a sample of 500 kindergartens in Korea, after excluding incomplete surveys and outliers, and a total of 224 responses were used for the analysis. Descriptive statistics were used to compare essential tasks and delegable tasks. The results show that 'Duty A. Nutrition Management', 'Duty B. Foodservice Management Practices', 'Duty C. Hygiene management of kindergarten foodservice', 'Duty D. Nutrition-Diet Education and counseling', and 'Duty F. Professionalism Enhancement' were recognized as essential tasks to be performed by kindergarten dietitians. All 16 tasks elements (100.0%) in 'Duty E. Managing snacks during semesters, and lunch/snack during breaks' were identified as delegable tasks. In conclusion, most tasks were recognized as essential tasks to be performed by kindergarten dietitians. On the other hand, 'Duty E. Managing Snacks during semesters, and lunch/snack during breaks' was considered a delegable task by public-attached kindergarten dietitians. It is recommended that public-attached kindergartens should consider additional workforce related to 'Duty E'. This study is expected to offer basic data on laws and regulations about the duties of kindergarten dietitians.
Journal of the Korean Society of Manufacturing Process Engineers
/
v.20
no.12
/
pp.30-35
/
2021
In this study, we developed an automatic module changer for agricultural implements for using in unmanned agricultural robots. An automatic module changer is attached by lowering from the top to bottom of the implements and fixing the four fastener bars attached to the implements in combination. The lift function was implemented using seesaw-type structures to keep the engagement point constant when the automatic module changer climbs and descends, and the switching function of the automatic module changer was implemented using the link device in the cam structure. We developed an algorithm to check the presence of attachment and opening/closing of the workpiece using limit switches and verified the performance through combination assessment and weight lift test to assess whether the combination was within the error range.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.