• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 춘계학술대회 논문집
• /
• pp.400-407
• /
• 1995

The straightness property is one of fundamental geometric tolerances to be strictly controlled for guideways of machine tools and measuring machines. The staightness measurement for long guideways was usually difficult to perform, and it needed additional equipments or special treatment with limited application. In this paper, a new approach is proposed using the profile matching technique for the long guideways, which can be applicable to most of straghtness measurements. An edge of relativelly sthort length is located along a divided section of a long guideway, and the local straightness measurement is performed. The edge is then moved to the next section with several positions overlap. After thelocal straightness profile is measured for every section along the long guideway with overlap, the global straightness profile is constructed using the profile matching technique based on theleast squares method. The proposed techinique is numerically tested for two cases of known global straightness profile arc profile and irregular profile and those profiles with and without random error intervention, respectively. When norandom errors are involved, the constructed golval profile is identical to the original profile. When the random errors are involved, the effect of the number of overlap points are investigated, and it is also found that the difference between the difference between the constructed and original profiles is very close to the limit of random uncertainty with juist few overlap points. The developed technique has been practically applied to a vertical milling machine of moving table type, and showed good performance. Thus the accuracy and efficiency of the proposed method are demonstrated, and shows great potential for variety of application for most of straightness measuirement cases using straight edges, laser optics, and angular measurement equipments.

• 한국전자파학회논문지
• /
• 제16권5호
• /
• pp.465-471
• /
• 2005

본 논문에서는 빔 전파법(BPM: Beam Propagation Method)을 이용하여 안테나 배열에서 발생된 집속된 빔의 전파 또는 집속 현상을 파악하는 방법을 제시하였다. 대물 쪽(object side)으로 적응적 집속을 위해 로트맨 렌즈를 이용하는 경우에 대해 회절이론을 바탕으로 집속 현상을 이론적으로 고찰하였다. 이를 검증하기 위해 상용 EM simulation tool을 이용하여 분석하기에는 구조물의 복잡성과 집속된 빔의 입전 설정 등 몇 가지 어려움이 있기에 이의 차선책(alternative solution)으로 푸리에 회절 이론에 기초한 빔 전파법을 이용하여 집속 현상을 계산하는 방법인 BPM을 소개하였다. 즉, 개구면을 통한 빔 전파는 Fresnel Diffraction Integral(FDI)에서 푸리에 변환 형태로 표현될 수 있으며 이는 BPM으로 발전시켜 개구면 형(aperture-type) 안테나로부터 전파되는 파의 빔 폭(beam width or spot size), 세 기(intensity or gain), 그리고 실제 초점거리를 산출하였다. $10\lambda$의 배 열 크기를 갖는 안테나에 대해 $20\lambda,\;30\lambda$, 그리고 $50\lambda$의 기하 초점거리(geometrical fecal length)를 갖는 파에 대해 BPM을 통해 계산한 결과, 빔 폭은 차례로 1.1\lambda,\;1.3\lambda,\;1.9\lambda$이 산출되었다.

• Structural Engineering and Mechanics
• /
• 제58권3호
• /
• pp.515-532
• /
• 2016

The elastoplastic response of functionally graded material (FGM) beams resting on a nonlinear elastic foundation to an eccentric axial load is investigated by using the finite element method. The FGM is assumed to be formed from ceramic and metal phases with their volume fraction vary in the thickness direction by a power-law function. A bilinear elastoplastic behavior is assumed for the metallic phase, and the effective elastoplastic properties of the FGM are evaluated by Tamura-Tomota-Ozawa (TTO) model. Based on the classical beam theory, a nonlinear finite beam element taking the shift in the neutral axis position into account is formulated and employed in the investigation. An incremental-iterative procedure in combination with the arc-length control method is employed in computing the equilibrium paths of the beams. The validation of the formulated element is confirmed by comparing the equilibrium paths obtained by using the present element and the one available in the literature. The numerical results show that the elastoplastic post-buckling of the FGM beams is unstable, and the post-buckling strength is higher for the beams associated with a higher ceramic content. Different from homogeneous beams, yielding in the FGM beam occurs in the layer near the ceramic layer before in the layer near metal surface. A parametric study is carried out to highlight the effect of the material distribution, foundation support and eccentric ratio on the elastoplastic response of the beams.

• 대한기계학회논문집A
• /
• 제20권10호
• /
• pp.3199-3210
• /
• 1996

The buckling and postbuckling behaviors were sutdied analytically and experimentally for stiffened laminated composite panels under compression loading. The panels with I-, blade, -and hat-shapeed stiffeners were investigated. In the analysis, the stiffened panels were anlyzed using the nonlinear finite element method combined with an improved arc-length method. The progressive failure analysis was done by adopting the maximum stress criterion and complete unloading failure model. The effects of the fiber angles were investigated on the buckling and postbuckling behaviors. In the experiment, the web and the lower cap of each stiffener were formed by the continuous lay-up of the skin for cocuring the stiffened panels. Therefore, the separation between stiffener and skin was not found in the junction part even after postbuckling ultimate load and the stiffened panels had excellent postbuckling load carrying capacity. A shadow moire thchnique was used to monitor the out-of-plane deformations of the panels. The piezoelectric films were attached to the panels to get the failure characteristics of the panel. The analytical results on the buckling load, postbuckling ultimate load, and failure pattern showed good agreement with the experimental results.

• 한국강구조학회 논문집
• /
• 제21권6호
• /
• pp.563-574
• /
• 2009

본 논문은 기하학적 비선형성을 가진 보존적 단일 하중 매개변수의 탄성 상태 공간구조의 탄성 분기 좌굴이론에 관한 수치 해석적 기본 방법 및 경로 추적, pin-pointing, 경로 전환을 기술하고 있다. 비선형 탄성 불안정 상태는 극한점과 분기점으로 분류될 수 있으며, 평형경로상의 평형점의 계산 및 평형경로상의 특이점을 찾기 위한 pin-pointing 반복계산을 수행하는 일반적인 비선형 수치해석법으로 극한점을 계산할 수 있다. 그러나 분기좌굴 해석을 위해서는 좌굴 후 분기경로의 추적을 위한 분기경로 전환 알고리즘이 추가적으로 필요하다. 본문에서는 에너지이론에 기초한 일반 탄성안정이론을 소개하고, 평형경로 추적, 다분기 좌굴점을 찾기 위한 간접법과 다분기의 경로 전환에 관한 이론을 전개한다. 분기좌굴 해석예제로 트러스로 이루어진 스타돔, 핀지지의 평면아치의 분기좌굴 해석을 수행하여 본문에서 제시한 수치해석법의 정확성 및 적용성을 검증한다.

• 수산해양기술연구
• /
• 제15권2호
• /
• pp.77-82
• /
• 1979

멸치는 남해안에서는 여러 단계의 크기의 것이 혼획되는데, 가다랭이 미끼용으로는 채장 6-7m의 것이 알맞으므로, 이 크기의 것을 가급적 언중 확보하기 위해서는, 그 분포상을 조사하여 적정 자원이 가장 많이 출현하는 해역을 알 필요가 있다. 또, 멸치의 크기에 따라 상품가치도 크게 다르므로 멸치 어업을 합리적으로 운영하기 위해서나, 자원의 관리를 위해서도 채장 조사는 중요하다. 여기서는 멸치어업이 주로 이루어지는 7월부터 12월의 한국 동남 해역에 있어서의 멸치의 분포상에 관하여 조사한 것을 보고한다

• 전기학회논문지
• /
• 제62권5호
• /
• pp.643-648
• /
• 2013

In this study, degradation was observed by irradiating UV rays to the polymer insulators which have been widely used in outdoor electric power facilities. For an indoor accelerated UV test, 0.55 w/m2 of UV rays were applied using a xenon-arc method. A UV detection system with 65 ${\phi}mm$ in diameter, 100 mm in length and 1.0 of brightness (F/#) has been designed. Even though efflorescence on the surface of polymer insulators wasn't observed according to the accelerated UV test. UV rays were detected at around 50% and 40% of insulation breakdown in EPDM and silicone-type insulators respectively. As degradation continued because of an indoor accelerated UV test, breakdown voltage with which UV rays can be detected in an early stage decreased as well. A silicone polymer insulator would be severer than EPDM polymer insulator in terms of surface degradation because of UV strength against $V_m/V_{BD}$ was high in silicone polymer insulators. UV strength in silicone-type insulators increased at 1,000 $kJ/m^2$ because contact angle at the intial stage sharply decreased to from $113^{\circ}$ to $92.1^{\circ}$.

• Current Photovoltaic Research
• /
• 제2권4호
• /
• pp.173-176
• /
• 2014

We have investigated the seed layer formation of front side contact using the inkjet printing process. Conductive silver ink was printed on textured Si wafers with 80 nm thick $SiN_x$ anti reflection coating (ARC) layers and thickened by light induced plating (LIP). The inkjet printable sliver inks were specifically formulated for inkjet printing on these substrates. Also, a novel method to prepare nano-sized glass frits by the sol-gel process with particle sizes around 5 nm is presented. Furthermore, dispersion stability of the formulated ink was measured using a Turbiscan. By implementing these glass frits, it was found that a continuous and uniform seed layer with a line width of $40{\mu}m$ could be formed by a inkjet printing process. We also investigated the contact resistance between the front contact and emitter using the transfer length model (TLM). On an emitter with the sheet resistance of $60{\Omega}/sq$, a specific contact resistance (${\rho}_c$) below $10m{\Omega}{\cdot}cm^2$ could be achieved at a peak firing temperature around $700^{\circ}C$. In addition, the correlation between the contact resistance and interface microstructures were studied using scanning electron microscopy (SEM). We found that the added glass particles act as a very effective fire through agent, and Ag crystallites are formed along the interface glass layer.

• 대한전자공학회논문지
• /
• 제26권7호
• /
• pp.157-165
• /
• 1989

무늬로 부터의 3차원 정보의 복구에 있어서, 투영의 왜곡효과는 왜곡된 무늬로 부터 구별되어야 한다. 그래서 본 논문에서는 가우스 구상의 보이는 면, 즉 반구상에서 무늬의 국소 해석을 통하여 면방향을 구하는 근사화된 최대유사 추정법을 제시한다. 정사영과 원을 영상시스템과 무늬소로 가정하고 원의 호길이에 일정하게 존재하는 법선방향의 정사영을 통한 법선 분포의 변화로 부터 면방향을 구한다. 구해진 면의 방향은 그래디언트 공간상의 한점으로 표시한 슬랜트와 틸트로 나타낸다. 또 구해진 면방향은 바늘지도로 나타낸다. 입력 데이터로는 임의로 만든 제주도 지도와 원무늬를 사용하여 알고리듬을 적용하였다.

• 농촌계획
• /
• 제11권2호
• /
• pp.9-19
• /
• 2005

The purpose of this study is to analyze the potential soil loss and hazard zone by the Revised Universal Soil Loss Equation(RUSLE) for preservation and management of land resources which is the base of ecosystem, and to grasp the relationship between RUSLE factors in the Nakdong River Basin. All thematic maps used in RUSLE are constructed through GIS and spatial analysis method derived from digital topographic maps, detailed soil maps, land-cover maps, and mean annual precipitation of 30 years collected respectively from National Geographic Information Institute, National Institute of Agricultural Science and Technology, and Ministry of Environment. The slope length of LS-factor that takes much times by the study area's wideness was calculated automatically through AML(Arc Macro Language) program developed by Van Remortel et al.(2001, 2003). The results are as follows; First, according to the soil loss estimation by the RUSLE, it shows that approximately 82% of the study area have relatively lower possibility of soil loss which is the 1 ton/ha in annual soil loss. While, 9.4% ($2,228km^2$) needed intensive and continuous management for soil loss. Because the amount of their annual soil loss was greater than 10 ton/ha that is optimum level suggested by Morgan(1995). For these areas, the author believe that a new approach which can minimize environmental impacts from soil loss through improvement of cultivation process and buffer forest zone should be applied. Second, according to the relationship between the RUSLE factors, topographical(LS-factor) and cover management(C-factor) conditions have a lot of influence on soil loss in case of the Nakdong River Basin. However, because of RUSLE factor's influence that affect to soil loss might be different based on the variety of spatial hierarchy and extent, it is necessary to analyze and evaluate factor's relationship in terms of spatial hierarchy and extent through field observations and further studies.