• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.1
• /
• pp.91-99
• /
• 2006

Large steel industries have nonlinear loads including electric arc furnaces and harmonic field measurements have shown that harmonic content of a waveform varies with time. Since the large loads are supplied from the power system grid, it must be recognized that not only will the system of utility be impacted, but neighboring customer system could be impacted as well. In this paper time-varying harmonics are evaluated by international harmonic standards IEEE Std. 519 and IEC 61000-3-6 using a cumulative probablistic approach.

• Journal of the Korean Chemical Society
• /
• v.40 no.3
• /
• pp.196-201
• /
• 1996

The analysis of trace cadmium in blood by using 10 folds diluted samples with 1% Triton X-100 and Fork platform tube at the ashing temperature of 500$^{\circ}C$ has been performed by GFAAS. In this study, good analytical results were obtained from peak area and peak height methods. The detection limits of SH and $D_2$ arc background correction are 0.02 ng/mL and 0.01 ng/mL, respectively. Relative standard deviation is within 5% at the level of 1.0 ng/mL.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.9
• /
• pp.766-772
• /
• 2011

Amorphous Si (a-Si) thin films of $p^+/p^-/n^+$ were deposited on $Si_3N_4$/glass substrate by using a plasma enhanced chemical vapor deposition (PECVD) method. These films were annealed at various temperatures and for various times by using a rapid thermal process (RTP) equipment. This step was added before the main thermal treatment to make the nuclei in the a-Si thin film for reducing the process time of the crystallization. The main heat treatment for the crystallization was performed at the same condition of $600^{\circ}C$/18 h in conventional furnace. The open-circuit voltages ($V_{oc}$) were remained about 450 mV up to the nucleation condition of 16min in the nucleation RTP temperature of $680^{\circ}C$. It meat that the process time for the crystallization step could be reduced by adding the nucleation step without decreasing the electrical property of the thin film Si for the solar cell application.

• Journal of Korea Foundry Society
• /
• v.22 no.3
• /
• pp.114-120
• /
• 2002

A new titanium based alloy, Ti-10Ta-10Nb, has designed to examine the improved mechanical properties and biocompatibility. A specimen of titanium alloy was melted in a consumable vacuum arc furnace and homogenized at $1050^{\circ}C$ for 24 h. The effect of hot rolling on microstructure was estimated after rolling at $400^{\circ}C$ and $800^{\circ}C$ respectively. Surface of melted alloy by consumable vacuum arc melting was consisted of rough surface and it was changed to sound surface by coating of $ZrO_2$ slurry on copper mold surface. The hardness of Ti-10Ta-10Nb alloy increased with the amount of${\alpha}+{\beta}$ phase. Ti-10Ta-10Nb alloy showed $Widmanst{\"{a}}ten$ structure by hot rolling at $800^{\circ}C$ and in the rolling ${\beta}-region$ was negligible effects on microstructure refining.

• Resources Recycling
• /
• v.25 no.3
• /
• pp.20-28
• /
• 2016

Assessment on adequate dosage of superplasticizer in eco-friendly ultra-high performance concrete (UHPC) containing industrial by-products was carried out from the standpoint of workability. Various types of industrial by-products, including blast-furnace slag, coal bottom ash and rapid-cooled electric arc furnace oxidizing slag, were utilized, and the effects of dosage of superplasticizer on the workability and strength of UHPC containing the by-products were evaluated. By utilizing the by-products, the workability of UHPC was improved and required dosage of superplasticizer was reduced. In addition, the material cost for UHPC with by-products was decreased due to reduced dosage of superplasticizer.

• Resources Recycling
• /
• v.33 no.2
• /
• pp.46-53
• /
• 2024

The residual heat and high CaO content present in the slag remaining in the ladle after the completion of continuous casting in the electric arc furnace (EAF) steelmaking process have been utilized to reduce power consumption and lime usage in the ladle furnace (LF) process. However, if the timing of such processes does not align with the LF and continuous casting operations, the recycling rate will decrease. To increase the slag recycling rate, the effect of ladle slag recycling methods, specifically pouring ladle slag into the slag pot in advance for subsequent recycling, on LF operations was analyzed. The slag liquefaction rate was calculated using the thermodynamic program Factsage 8.3 for ladle molten slag recycling methods. By applying each of the 10 heats operations for the ladle slag recycling methods, the desulfurization ability and LF operation performance were compared. It was found that when slag was immediately recycled into the ladle after continuous casting was completed, power consumption decreased by 0.3 MWh, LF operation time was shortened by 1.2 minutes, and the desulfurization rate increased by 5.8%.

• Korean Journal of Materials Research
• /
• v.17 no.5
• /
• pp.256-262
• /
• 2007

Effects of interlayer and the combination of different coating methods on the mechanical and corrosion behaviors of TiN and CrN coated on 420 stainless steel have been studied. STS 420 specimen were tempered at $300^{\circ}C$ for 1 hr in vacuum furnace. The TiN and CrN thin film with 2 ${\mu}m$ thickness were coated by arc ion plating and DC magnetron sputtering following the formation of interlayer for pure titanium and chromium with 0.2 ${\mu}m$ thickness. The microstructure and surface analysis of the specimen were conducted by using SEM, XRD and roughness tester. Mechanical properties such as hardness and adhesion also were examined. XRD patterns of TiN thin films showed that preferred TiN (111) orientation was observed. The peaks of CrN (111) and $Cr_2N$ (300) were only observed in CrN thin films deposited by arc ion plating. Both TiN and CrN deposited by arc ion plating had the higher adhesion and hardness compared to those formed by magnetron sputtering. The specimen of TiN and CrN on which interlayer deposited by magnetron sputtering and thin film deposited by arc ion plating had the highest adhesion with 22.2 N and 19.2 N. respectively. TiN and CrN samples shown the most noble corrosion potentials when the interlayers were deposited by using magnetron sputtering and the metal nitrides were deposited by using arc ion plating. The most noble corrosion potentials of TiN and CrN were found to be approximately -170 and -70 mV， respectively.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 2000.06a
• /
• pp.179-193
• /
• 2000

Aluminium titanate (Al₂TiO5) with an excellent thermal shock resistant and a low the expansion coefficient was obtained by solid solution with MgO, SiO₂, and ZrO₂ in the Al₂TiO5 lattice or in the grain boundary solution through electrofusion in an arc furnace. However, these materials have low mechanical strength due to the presence of microcracks developed by a large difference in thermal expansion coefficients along crystallographic axes. Pure Al₂TiO5 tends to decompose into α-Al₂O₃ and TiO₂-rutile in the temperature range of 750-1300℃ that rendered it apparently useless for industrial applications. Several thermal shock tests were performed: Long therm thermal annealing test at 1100℃ for 100h; and water quenching from 950 to room temperature (RT). Cyclic thermal expansion coefficients up to 1500℃ before and after decomposition tests was also measured using a dilatometer, changes in the microstructure, thermal expansion coefficients, Young's modulus and strengths were determined. The role of microcracks in relation to thermal shock resistance and thermal expansion coefficient is discussed.

• Proceedings of the Korean Society for Emotion and Sensibility Conference
• /
• 2009.11a
• /
• pp.265-268
• /
• 2009

전기로 산화 슬래그 골재는 철강산업의 부산물을 재활용한다는 측면에서 친환경적일 뿐만 아니라 고갈되고 있는 골재자원을 대체할 수 있다는 측면에서 중요한 가치를 지닌다. 본 연구에서는 다량의 철성분을 함유하고 있어 높은 밀도를 나타내는 전기로 산화슬래그 골재를 사용한 친환경 콘크리트의 횡구속 성능에 관하여 검토하였다. 이 실험에서는 전기로 산화슬래그 굵은 골재 및 잔골재를 적용한 콘크리트 공시체를 제작하여 천연 굵은 골재와 잔골재를 적용한 콘크리트의 횡구속 거동을 파악하였다. 실험변수는 콘크리트 제작에 사용한 골재의 종류, 횡보강에 사용한 나선 철근의 항복강도로 하였다. 실험결과 전기로 산화슬래그 골재를 사용하였을 경우 천연골재를 사용한 실험체와 유사한 횡구속 효과를 보였다.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.11a
• /
• pp.105-108
• /
• 2001

In this paper, we evaluated the suitability of steel slag(is divided with electric arc furnace slag and converter slag) as concrete aggregate by measuring physical and chemical characteristics of it. The steel slag mainly contains SiO$_2$ and CaO as the chemical composition. The reaction with water and a little of free CaO in the slag causes slag's volume to expand. Therefore, we used several aging methods in order to decrease the characteristics of slag volume expansion. The physical properties of steel slag aggregate are researched and then the strength of concrete with the steel slag aggregate is measured.