• Journal of radiological science and technology
• /
• v.34 no.2
• /
• pp.141-147
• /
• 2011

We developed an alternative radiation shielding material which is economical and has high protection efficiency. We validated the material in the form of sheet to make an apron. We increased the rate of barium and mixed tourmaline into silicon to improve the flexibility and protection rate of the sheet. The results showed that the shielding effect at low radiation energy is good enough with both 5 mm and 7 mm thickness. In the future, we will perform a quantitative evaluation of the reproducibility, volumetric efficiency, and porosity in mixing the ingredients.

• Korean Journal of Digital Imaging in Medicine
• /
• v.11 no.1
• /
• pp.21-26
• /
• 2009

In operation room, the use of the C-arm unit is increasing. So, the radiation dose of the person who work in operation room was even more increased than before. Thus, this study is shown the measurement of expose dose and the way for decrease of the radiation dose by using the C-arm unit. The experiment was performed with the C-arm unit and used a phantom which is similar to tissue of the human body and fluoro-glass dosimeter for dose measurement. The expose dose were measured by the tube position(over tube, under tube) of the C-arm unit, distance(50, 100$\sim$200cm), direction(I, II, III, IV), runtime(1min, 3min), wearing of the apron. The radiation dose was decreased twice and three times at under tube rather than over tube. The I direction was measured 20$\sim$30% more than the others. The biggest expose dose is 50cm from center on distance. The expose dose is decreased to far from center. In case of Wearing of the apron, the radiation dose was decreased 60$\sim$90% by the distance. But there weren't change of the radiation dose by C-arm tube position. In present, by increasing the usage of the C-arm unit, the radiation dose is inevitable. So, this study recommends us to use the under tube of the C-arm unit. Also, Wearing of the apron is required for minimum of the radiation exposure.

• Korean Journal of Human Ecology
• /
• v.23 no.5
• /
• pp.843-859
• /
• 2014

The purpose of this study is to find the differences among the clothing brands through examination of present situation about uniform design in domestic coffee houses and provide the basic materials in developing uniform designs to reflect the brand identity. For research contents and method, the overall circumstances were examined about the domestic coffee houses and their uniforms at large via literature review. Then, characteristics on their 10 uniform designs were reviewed according to item, color, pattern and accessary. The following are results. First, cardigan, cap, and necktie according to the individual brand are added with basis of shirt and apron in composition of coffeehouse's uniform. Second, in cardigan, those colors including black, navy and brown are used, reminding of the coffee. Brand logo or symbol is also presented on it, which addresses the brand image. Third, the kind of shirt consists mainly with long or short shirt blouse and long sleeve or short sleeve pique shirt. Job title or gender differentiates the shape and color. Fourth, one-piece type is commonly applied for the apron. At the same time, a short skirt is put on as well. An image expression is often found by the unique brand color also, but mostly, some dark tones like brown or black are largely used. Fifth, in cap, various kinds are worn including the cap as in the case of baseball, fedora, beret, and hunting cap. In color, black or brown color same to that of apron is common, which fails to show differentiation. Thus, consideration of color remix with application of brand symbol is thought to be an alternative to this.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2000.04a
• /
• pp.55-55
• /
• 2000

Cylinder machine usually gives more fiber orientation than fourdrinier and has limitation in machine speed because of fiber wash-off caused by centrifugal force in case of adding machine speed. This study aimed at improvement of paper formation and higher productivity by setting up an apron in vat inlet and by adjustment of mould water head. As results, there were improvement of formation and increase of machine speed, which ultimately improve productivity. Setting up an apron successfully decreased fiber wash-off. Fiber orientation and two-sideness of ash distribution became less severe. These results could lead to better dimension stabilities in the CD through mitigation of fiber orientation and also could result in less curl from two-sideness of paper. The proper adjustment of water head inside the cylinder mould proved to be important factor not only in paper formation but also in decreasing paper two-sideness.

• Journal of Korea Water Resources Association
• /
• v.38 no.3 s.152
• /
• pp.189-198
• /
• 2005

This study showed that numerical simulation can be effectively used to analyze discharge capacity according to the form and arrangement of the lock gate of a tidal power plant. For the numerical simulation, FLOW-3D with Reynolds-averaged Navier-Stokes equation as a governing equation was used. This study found that improvement of apron length and approach angle of guide wall of the lock gate causes differences in discharge capacity of $10\%$ or more. In addition, there was a difference of discharge capacity caused by the connecting structures of the drainage gate and hydraulic turbine structure and the side slope at the end of apron. This study also showed that hydraulic investigation to enhance a discharge capacity is needed when the lock gate is designed and that numerical model experiments can be a useful analysis tool to design the drainage structure, as well as the hydraulic model experiment.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.24 no.1
• /
• pp.23-30
• /
• 1982

The aim of this report is to analyze the Occurring rate of damage at each region of head works and to clear its damaged mechanism, centering around the destroyed situations of head works along both Musim and Bochong Rivers suffered from the storm flood occurred on July 22, 1980. The results obtained from the investigation of 25 head works taken for samples are summarized as follows. 1. The occurring rate of damage at each region of head works showed the largest number of 100 percentage in the revetment and protected riverbed work respectively, in the order of the next largest number, 68 percentage in weir body, 56 percentage in apron and 36 percentage in bank. 2. The destructive damage of revetment influenced largely on sweeping bank away, and destructive sufferings of weir body and protected bed work affected on the destructi on of apron, otherwise the destructive sufferings of apron reversely also acted on the- destruction of weirbody and protected bed work. In other hand, partial damage of weir body at the side of revetment is largely influenced by destructive sweeping away of bank. 3. It was showed that the destructive phenomena of weir body occurred largely at the part of concentrated flow and also had a deep relation with scoring by concentrated flow around upstream foundation of weir. 4. The suffered region of revetment is the down stream part just near weir body and the degree of damage is more severe at the curved part of bank that center of flow is concentrated.

• Journal of the Korea Convergence Society
• /
• v.12 no.1
• /
• pp.105-110
• /
• 2021

Radiation shielding of affinity material, which is widely used in medical institutions, is made in sheet form and is mainly applied to apron. Shielding performance is presented based on lead equivalent, and is presented as 0.25-0.50mmPb. In the case of shielding materials where lead is used as the main material, the shielding performance can be adjusted by thickness due to the excellent machinability of lead. However, eco-friendly shielding sheets are difficult to control shielding performance based on thickness criteria as shielding performance varies depending on the content of shielding materials, the properties of polymeric materials that are base materials, and the technical differences in the process. In this study, shielding sheets were manufactured based on thickness to solve these problems and the shielding performance was compared in this study. As a result, it was shown that the laminated structure shielding sheet was more effective.

• Journal of the Korea Convergence Society
• /
• v.12 no.11
• /
• pp.119-126
• /
• 2021

Radiation shielding clothing for medical institutions is used based on lead equivalent of 0.25 mmPb. However, this study intends to study the shielding suit that can guarantee the user's activity while considering the sensitivity of each part of the body. By manufacturing based on eco-friendly shielding material, it was attempted to solve the weight problem and environmental problem of existing lead aprons, and to present the same shielding performance as lead equivalent in thickness. The fabric of the produced shielding sheet was manufactured through a calendar process that adjusts the thickness of the shielding sheet from lead equivalent 0.12 mmPb to 0.32 mmPb. In addition, the usability evaluation of the manufactured shielding clothes was conducted for the subjects who were workers in medical institutions. As a result, the activity became easier and the weight was reduced by 0.26 kg. In the future, it is thought that it is necessary to improve the shielding suit design considering the activity.

• Journal of radiological science and technology
• /
• v.46 no.6
• /
• pp.543-551
• /
• 2023

In this study, the aim was to assess the shielding performance of different 3D printing materials, specifically those produced using FDM, SLA, and CJP methods, with a focus on their application as shielding devices in clinical settings. Additionally, the weight of lead shielding materials can evoke reluctance in pediatric patients undergoing X-ray imaging. A total of 12 materials were printed using their respective 3D printers. These materials were then subjected to X-ray testing using diagnostic X-ray equipment and an exposure meter. The goal was to evaluate their shielding capabilities in comparison to 1 mm lead. The results of this evaluation revealed that VisiJet PXL-Pastel, produced using the CJP method, exhibited the highest shielding performance. Therefore, VisiJet PXL-Pastel by CJP method was selected for the creation of a shielding device designed for pediatric reproductive organs. Subsequent tests demonstrated that both the newly created shielding device and conventional lead shielding equipment achieved the same maximum shielding rate at 50 kVp. Specifically, the shielding rate for the 3D printed device was measured at 84.53%, while the conventional lead shielding equipment, categorized as Apron1 (85.74%), Apron2 (99.98%), and Apron3 (99.04%), demonstrated similar performance. In conclusion, the CJP-produced VisiJet PXL-Pastel material showcased excellent radiation shielding capabilities, allowing for anatomical observations of the target organs and their surrounding structures in X-ray images. Furthermore, its lower weight in comparison to traditional lead shielding materials makes it a clinically practical and useful choice, particularly for pediatric applications.

• Progress in Medical Physics
• /
• v.26 no.2
• /
• pp.93-98
• /
• 2015

The purpose of this study is to see the usefulness of lead apron for critical organs near the breast under examining. For clinical experiment, 30 female volunteers who agreed to their participation in the experiments, were chosen and divided into two groups, 15 in group A and 15 in group B respectively. group A is to see whether each side of breast under mammography affects to other side glandular on the critical organs is same, because it is not allowed to scan the both breast for same person or to scan repeatedly. Group B is to see the effectiveness of lead apron during the mammography of right breast. Glass dosimeters were placed on the thyroid, the contralateral breast, and lower abdomen where near the breast during examining. The average glandular doses on the surface in mammography of the thyroid gland, the contralateral breast, the lower abdomen were 0.0692 mGy, 0.6790 mGy, and 0.0122 mGy, respectively, which was an extremely low level of glandular dose. In group B, as to the thyroid gland, average dose was decreased from 0.0922 mGy to 0.0158 mGy. The average dose of contralateral breast was decreased from 0.8575 mGy to 0.0286 mGy. The average doses of lower abdomen was decrease 0.0150 mGy to 0.0173 mGy. As to the lower abdomen, dose decreased from 0.0150 mGy before the use of an apron down to 0.0173 mGy after the use. As p-value was under 0.05, statistically significant difference was observed between the two groups. Wearing an apron can have the protective effects on the thyroid gland up to 20 times lower than not wearing one. Besides, it is also necessary to protect the other breast during the examination by wearing one.