• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.3 no.1 s.4
• /
• pp.75-83
• /
• 2004

This paper describes the design, fabrication, and measurement of a low side lobe antenna for RSE base station of the ETCS which is one of the ITS services. The antenna is installed on the gantry of road side and provides the wireless communication lint between vehicles and RSE. The required characteristics of ETCS base station antenna are low sidelobe and specific beam pattern by the road and install environment and installed place of OBU. To minimize the affects of multipath signal by reflection, Circular polarization is required. To get low sidelobe of antenna, array configuration and weighting factor by Taylor distribution in radiator elements are applied. The measured results of fabricated antenna are as follows; return loss of 130MHz by -10dB, an axial ratio of 2.6dB, and a gain of 17dBi. It is found that the measured beam patterns are similar to design results.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.153-157
• /
• 1997

This paper presents a patch antenna design method using microwave dielectric ceramic substrate. Before manufactirung the GPS(Global Positioning System)antenna such contents as input impedence resonent frequency and quality factor and efficiency are surveyed theolitically for design and parameters for manufacturing the antenna are found.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.6
• /
• pp.562-568
• /
• 2013

This paper presents a design of a wireless power transfer system based on magnetic resonant coupling technology with in-band wireless communication. To increase the transmission distance and compensate for the change in the effective capacitance due to the varying distance, the proposed system used a loop antenna with a selectable capacitor array. Because the increased transmission distance enables multiple charging, we added a communication protocol operated at the same frequency band to manage a network and control power circuits. In order to achieve the efficient bandwidth in both power transfer mode and communication mode, the S-parameters of the loop antennas are adjusted by switching a series resistor. Our test results showed that the loop antenna achieved a high Q factor in power transfer mode and enough passband in communication mode.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2004.11a
• /
• pp.406-406
• /
• 2004

• ETRI Journal
• /
• v.34 no.1
• /
• pp.118-121
• /
• 2012

In this letter, a miniaturized log-periodic dipole array (LPDA) antenna operating from 1 GHz to 6 GHz is proposed for portable direction finding applications. To reduce the lateral size of an LPDA antenna, bow-tie elements and a top-loading technique are utilized and spacing factor is decreased to reduce the spacing between the LPDA elements. The proposed miniaturized LPDA antenna has the measured gain and front-to-back ratio ranging from 1.2 dBi to 3 dBi and from 7 dB to 22 dB, respectively.

• Journal of electromagnetic engineering and science
• /
• v.17 no.4
• /
• pp.228-232
• /
• 2017

The radiation properties and fabrication precautions of a 3D printed, electrically small folded spherical meander wire monopole antenna are investigated. The antenna is self-resonant and shows sufficiently high radiation efficiency at an electrical size ka of 0.4, with the radiation quality factor Q approaching the lower physical bound. In antenna fabrication, the possible structural deformation due to gravity is examined before the antenna frame is 3D-printed. The required conductivity is achieved by multiple manual paintings of a silver paste. The radiation efficiency and pattern show very good agreement with the computed expectations, whereas the resonant frequency deviates by 11.8%. The method to minimize such a fabrication error when using 3D printing technology for wire antennas is discussed.

• Smart Media Journal
• /
• v.13 no.1
• /
• pp.45-51
• /
• 2024

Long Range Wide Area Network (LoRaWAN) is a widely adopted Internet of Things (IoT) protocol due to its high range and lower energy consumption. LoRaWAN utilizes Adaptive Data Rate (ADR) for efficient resource (e.g., spreading factor and transmission power) management. The ADR manages these two resource parameters on the network server side and end device side. This paper focuses on analyzing the ADR and Gaussian ADR performance of LoRaWAN. We have performed NS3 simulation under a static scenario by varying the antenna height. The simulation results showed that antenna height has a significant impact on the packet delivery ratio. Higher antenna height (e.g., 50 m) has shown an improved packet success ratio when compared with lower antenna height (e.g., 10 m) in static and mobility scenarios. Based on the results, it is suggested to use the antenna at higher allevation for successful packet delivery.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.12
• /
• pp.1132-1138
• /
• 2011

In this paper, a method for synthesizing the linear antenna array patterns with broad nulls(BN) at the interference directions is newly presented. Opposit to the conventional methods in which the weights of array elements are optimized for BN control, this method simplifies the control process for multiple BN directions and widths by optimally perturbing the zero positions inherent to Schelkunoff polynomial transformed from the array factor. It is also shown that this method can be easily applicable to the phased array antennas. The proposed scheme is numerically verified by substituting the extracted complex weights into the array factor.

• Publications of The Korean Astronomical Society
• /
• v.29 no.3
• /
• pp.53-58
• /
• 2014

We improved the antenna efficiency of the Taeduk Radio Astronomy Observatory (TRAO) 13.7-m radio telescope by adjusting the antenna panels based on digital photogrammetric measurements. First of all, we measured the surface accuracy of the main reflector of this antenna at three elevation angles of $35^{\circ}$, $45^{\circ}$, and $60^{\circ}$. We performed a total of four sets of the photogrammetric measurements and panel adjustments. When adjusting the panels, we positioned the antenna to the zenith and applied the measured data sets at the elevation of $45^{\circ}$. We found that the antenna surface accuracy has been improved by a factor of ~ 3 times after the final adjustment in comparison with the value before the adjustments. And we also found that the antenna surface accuracy tended to be slightly better at the elevation angles of $35^{\circ}$ and $60^{\circ}$ than that at the elevation angle of $45^{\circ}$. After the final panel adjustment, the aperture and beam efficiencies of the telescope have has been improved from 35% to 44%, and from 41% to 51%, respectively.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.10 no.5
• /
• pp.77-82
• /
• 2010

The tracking performance of the big tracking antenna system using Radio Frequency is very important for the tracking and position measuring for the flight vehicle, but the precise measuring of the tracking performance is not easy, especially for the big antenna system such as ground telemetry antenna or tracking radar in space application because it's characteristics could be different in accordance with the antenna direction. In this paper, the error factors impacting on the tracking performance (pointing accuracy and tracking accuracy) and the ranges of each factor are reviewed, and the simple and efficient method to measure the tracking performance is introduced which using low earth orbit as the signal source. Finally, the measurement results for the telemetry ground antenna in NARO Space Center are reviewed.