• 한국초전도ㆍ저온공학회논문지
• /
• 제8권3호
• /
• pp.5-8
• /
• 2006

The effect of annealing time in Metal Organic Deposition(MOD) method was investigated at reduced total pressure. As the total annealing pressure was reduced, the growth rate of YBCO films increased from 0.14nm/sec at atmospheric pressure to 4.2nm/sec at 1 Torr. For the total pres sure of 700, 500, 300, 100, and 1 Torr, the optimal annealing times of 60, 40, 20, 10, 2minutes were found in our experimental conditions. When the an nealing time was short, poor crystallinity or un-reacted phase was obtained. Also, the degradation of YBCO films occurred when exposed longer to the humid ambient at the high annealing temperature. The reduced pressure was found effective to in crease the growth rate and to control the pore size of the YBCO films in MOD method. A fast growth of MOD-YBCO films was realized with high critical current density over $1MA/cm^2$ using reduced pressure annealing. Large pores, usually observed at atmospheric pressure in MOD method, disappeared and also, the number of pores was reduced.

• 마이크로전자및패키징학회지
• /
• 제21권4호
• /
• pp.57-62
• /
• 2014

미래형 유연소자 개발 시 비용감소 및 공정적합성 개선을 위해 동박을 잉크젯 프린팅법을 이용해 공중합체 유연기판 상 형성하고, 전기적 특성에 열처리 분위기가 미치는 영향을 확인하기 위해 3 종류의 환원분위기에서 열처리를 진행하여 보았다. 그 결과 200도의 낮은 온도에서 환원 특성이 뛰어난 포름산 분위기에서 전도체 수준의 비저항은 얻을 수 있었으나, 열처리 시 발생하는 응력으로 인해 발생된 표면균열에 기인해 그 값이 기존 동박에 비해 매우 높았다. 이에 비정질재료에서 응용되는 응력해소법을 응용하여 표면균열을 억제한 결과 230도 열처리 시 기존 열처리 방법에서는 $7.4{\mu}{\Omega}cm$의 비저항을 보이나, 응력해소를 통한 표면 균열이 억제된 시편에서는 $3.4{\mu}{\Omega}cm$의 비저항 값을 얻을 수 있었다. 특히 등온열처리에 의한 응력해소 효과를 확인하기 위해 동일 온도에서 등온시간 없이 열처리를 진행한 결과, 표면균열이 억제되지 못함을 확인할 수 있었다.

• 한국전기전자재료학회논문지
• /
• 제15권5호
• /
• pp.441-448
• /
• 2002

The electrical properties of the GaN-based green light emitting diodes(LEDs) with the Mg-doped p-GaN layer activated in $N_2$ or $O_2$ ambient have been compared. For the $N_2$ -ambient activation the current-voltage behavior of LEDs has been found to be improved when the Mg dopants activation was performed in the higher temperature. However, for the $O_2$-ambient activation the current-voltage characteristic has been observed to be enhanced when the Mg dopants activation was carried out in the lower temperature. The minimum forward voltage at 20mA was obtained to be 4.8 V for LEDs with the p-GaN layer activated at $900^{\circ}C$ in the $N_2$ ambient and 4.5V for LEDs with the p-GaN layer treated at $700^{\circ}C$ in the $O_2$ambient, repectively. The forward voltage reduction of the LEDs treated in the $O_2$-ambient may be related to the oxygen co-doping of the p-GaN layer during the activation process. The $O_2$ -ambient activation process is useful for the enhancement of the LED performance as well as the fabrication process since this process can activate the Mg dopants in the low temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.457-458
• /
• 2009

In this work, transparent conducting Al-doped zinc oxide (AZO) films were prepared on Coming glass substrate by RF magnetron sputtering using an Al-doped ZnO target (Al: 2 wt.%) at room temperature and all films were deposited with athickness of 150 nm. We investigated the effects of the post-annealing temperature and the annealing ambient on structural, electrical and optical properties of AZO films. The films were annealed at temperatures ranging from 300 to $500^{\circ}C$ in steps of $100^{\circ}C$ using rapid thermal annealing equipment in oxygen. The thickness of the film was observed by field emission scanning electron microscopy (FE-SEM) and grain size was calculated from the XRD spectra using the Scherrer equation and their electrical properties were investigated using a hole measurement and the reflectance of AZO films was investigated by UV-VIS spectrometry.

• 한국세라믹학회지
• /
• 제48권4호
• /
• pp.316-322
• /
• 2011

Tin oxide thin films were deposited by rf reactive sputtering and annealed at $400^{\circ}C$ for 1 h in vacuum. To minimize the influence such as reduction, oxidation, and doping on tin oxide thin films during annealing, a vacuum ambient annealing was adopted. The structural, optical, and electrical properties of tin oxide thin films were characterized by X-ray diffraction, atomic force microscope, UV-Vis spectrometer, and Hall effect measurements. After vacuum annealing, the grain size of all thin films was slightly increased and the roughness ($R_a$) was improved, however irregular and coalesced shapes were observed from the most of the films. These irregular and coalesced crystal shapes and the possible elimination of intrinsic defects might have caused a decrease in both carrier concentration and mobility, which degrades electrical conductivity.

• 한국전기전자재료학회논문지
• /
• 제13권12호
• /
• pp.1003-1010
• /
• 2000

Thin films of vanadium oxide(VOx) have been deposited by r.f. magnetron sputtering from V$_2$O$\_$5/ target in gas mixture of argon and oxygen. Crystal structure, surface morphology, chemical composition, molecular structure and optical properites of films in-situ annealed in O$_2$ambient with various heat-treatment conditions are characterized through XRD, SEM, AES, RBS, RTIR and optical absorption measurements. The films annealed below 200$\^{C}$ are amorphous, and those annealed above 300$\^{C}$ are polycrystalline. The growth of grains and the transition of vanadium oxide into the higher oxide have been observed with increasing the annealing temperature and time. The increase of O/V ratio with increasing the annealing temperature and time is attributed to the diffusion of oxygen and the partial filling of oxygen vacancies. It is observed that the oxygen atoms located on the V-O plane of V$_2$O$\_$5/ layer participate more readily in the oxidation process. Also indirect and direct optical band gaps were increased with increasing the annealing temperature and time.

• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.701-706
• /
• 2006

In addition to its similarity to genuine diamond film, diamond-like carbon (DLC) film has many advantages, including its wide band gap and variable refractive index. In this study, DLC films were prepared by the RF PECVD (Plasma Enhanced Chemical Vapor Deposition) method on silicon substrates using methane $(CH_4)$ and hydrogen $(H_2)$ gas. We examined the effects of the post annealing temperature on the structural variation of the DLC films. The films were annealed at temperatures ranging from 300 to $900^{\circ}C$ in steps of $200^{\circ}C$ using RTA equipment in nitrogen ambient. The thickness of the film and interface between film and substrate were observed by surface profiler, field emission scanning electron microscopy (FESEM), high resolution transmission electron microscopy (HRTEM), respectively. Raman and X-ray photoelectron spectroscopy (XPS) analysis showed that DLC films were graphitized ($I_D/I_G$, G-peak position and $sp^2/sp^3$ increased) ratio at higher annealing temperature. The variation of surface as a function of annealing treatment was verified by a AFM and contact angle method.

• 대한금속재료학회지
• /
• 제48권1호
• /
• pp.77-84
• /
• 2010

Annealing characteristics of an oxygen free copper (OFC) processed by differential speed rolling (DSR) were investigated in detail. An OFC sample with a thickness of hum was rolled to 35% reduction at ambient temperature without lubrication, varying the differential speed ratio from 1.0:1 to 2.2:1, and then annealed for 0.5h at various temperatures from 100 to $400^{\circ}C$. Different recrystallization behavior was observed depending on the differential speed ratio, especially in the case of annealing at $200^{\circ}C$ Complete recrystallization occurred in the specimens annealed at temperatures above $250^{\circ}C$ regardless of the differential ratios. The hardness distribution in the thickness direction of the rolled OFC sheets varied depending on the differential speed ratios. These annealing characteristics were explained by the magnitude of shear strain introduced during rolling.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.321-322
• /
• 2009

Al doped ZnO films deposited on glass substrate using RF magnetron sputtering in Ar and $Ar+H_2$ gas ambient at $100^{\circ}C$. The films deposited in $Ar+H_2$ were hydrogen-annealed at the temperature of $150\sim300^{\circ}C$ for 1hr. The lowest resistivity of $4.25\times10^{-4}{\Omega}cm$ was obtained for the AZO film deposited in $Ar+H_2$ after hydrogen annealing at $300^{\circ}C$ for 1hr. The average transmittance is above 85% in the range of 400-1000 nm for all films. The absorption efficiency of solar cell was improved by using the optimized AZO films as a top electrode.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.5-6
• /
• 2009

In this paper, plasma ion implant is performed with $PH_3$ gas diluted by helium gas on P-type Si wafer (100). Spike Rapid Thermal Processing(RTP) annealing performed for 30~60 sec from $800\;^{\circ}C$ to $1000\;^{\circ}C$ in $N_2+O_2$ ambient. Crystalline defect is analyzed by Transmission Electron Microscope(TEM) and Double crystal X-ray Diffraction(DXRD). Contact resistivity($\rho c$), contact resistance(Rc) and sheet resistance(Rs) are analyzed by measuring Transfer Length Method(TLM) using 4155C analysis. As annealing temperature increase, Rs decrease and ${\rho}c$ and Rc increase at temperature higher than $850\;^{\circ}C$. We achieve low Rs, ${\rho}c$ and Rc with Plasma ion implant and spike RTP.