• 대한전자공학회논문지
• /
• 제27권4호
• /
• pp.563-570
• /
• 1990

A silicon pressure sensor made of a full bridge of diffused resistors was designed and fabricated using semiconductor integrated circuit process. Thin diaphragms with 30\ulcorner thickness were obtained using anisotropic wet chemical etching technique. Our device showed strong temperature dependence. Compensation networks are used to compensate for the temperature dependence of the pressure sensor. The bridge supply voltage having positive temperature coefficient by compensation networks was utilized against the negative temperature coefficient of bridge output voltage. The sensitivity fluctuation of pressure sensor before temperature compensation was -1700 ppm/\ulcorner, while it reduced to -710ppm\ulcorner with temperature compensation. Our result shows that the we could develop accurate and reliable pressure sensor over a wide temperature range(-20\ulcorner~50\ulcorner).

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 전기.전자공학 학술대회 논문집(I)
• /
• pp.481-485
• /
• 1987

The fabrication of a micro mass flow sensor on a silicon chip by means of micro-machining technology is described on this paper. The operation of micro mass flow sensor is based on the heat transfer from a heated chip to a fluid. The temperature differences on the chip is a measure for the flow velocity in a plane parallel with the chip surface. An anisotropic etching technigue was used for the formation of the V-type groove in this fabrication. The micro mass flow sensor is made up of two main parts ; A thin glass plate embodying the connecting parts and mass flow sensor parts in silicon chip. This sensor have a very small size and a neglible dead space. Micro mass flow sensor can fabricate on silicon chip by micro machining technology too.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권6호
• /
• pp.360-366
• /
• 2000

This paper presents the fabrication and test of a micropump consisting of a pair of Al flap valves and a phase-change type actuator. The actuator is composed of a heater, a silicone rubber diaphragm and a working fluid chamber. The diaphragm is actuated by the vaporization and the condensation of the working fluid. The micropump is fabricated by the anisotropic etching, the boron diffusion and the metal evaporation. The forward and the backward flow characteristics of the flap valves illustrate the appropriateness as a check valve. Also, the flow rate of the micropump is measured. When the square wave input voltage of 8 V, 70% duty ratio and 2 Hz is applied to the heater, the maximum flow rate of the micropump is $97\muell/min$ for zero pressure difference.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 G
• /
• pp.3268-3270
• /
• 1999

This paper presents the fabrication of a micro electromagnetic flowmeter for liquid flow rate measurement. The flowmeter consists of a silicon flow channel with two electrodes and two permanent magnets. The micro flow channel and the detection electrodes are fabricated by the anisotropic etching of two silicon substrates and the metal evaporation process respectively. If conductive fluid passes through a magnet field, electromotive force is generated and detected by two electrodes. When the flow rate is 2.6 ml/sec, the measured output voltage is 7.4 mV.

• 센서학회지
• /
• 제14권5호
• /
• pp.357-361
• /
• 2005

Low-stress silicon nitride (LSN) thin films with embedded metal line have been developed as free standing structures to keep microspheres in proper locations and localized heat source for application to a chip-based sensor array for the simultaneous and near-real-time detection of multiple analytes in solution. The LSN film has been utilized as a structural material as well as a hard mask layer for wet anisotropic etching of silicon. The LSN was deposited by LPCVD (Low Pressure Chemical Vapor Deposition) process by varing the ratio of source gas flows. The residual stress of the LSN film was measured by laser curvature method. The residual stress of the LSN film is 6 times lower than that of the stoichiometric silicon nitride film. The test results showed that not only the LSN film but also the stack of LSN layers with embedded metal line could stand without notable deflection.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 추계학술대회 논문집 학회본부
• /
• pp.416-418
• /
• 1994

In this study, a silicon piezoresistive accelerometer is designed and fabricated using $p^+$ etch stop layer. The accelerometer consists of a seismic mass and tour cantilevers, and is fabricated mainly by the anisotropic etching method using EPW as an etchant. Eight piezoresistors are properly arranged and connected to make a bridge circuit so that acceleration in only one direction may be measured. The etch stop method is adequate to the mass-production and the precise thickness control of the diaphragms as well, whet compared with the electrochemecal etch stop method.

• 전자공학회논문지SC
• /
• 제45권4호
• /
• pp.29-34
• /
• 2008

일반적으로 종래의 3 차원 홀 센서는 일반적으로 $B_z$에 대한 감도가 $B_x,\;B_y$에 대한 감도의 약 1/10정도에 그친다. 따라서 본 연구에서는 새로운 구조를 갖는 3 차원 홀 센서를 제안하였다. 이방성 식각을 이용하여 트랜치를 형성함으로써 감도를 약 6배 증가시켰다. 또한 자속을 집속시키기 위하여 웨이퍼 후면에 강자성체 박막을 증착시킴으로써 $B_z$에 대한 감도를 $B_x,\;B_y$에 대한 감도의 약 80%정도로 증가시켰다. 제작된 센서의 감도는 각각 361V/A T, 335V/A T, 그리고 286V/A T로 측정되었다. 센서는 $360^{\circ}$ 회전체에 대해 사인파의 출력을 가졌다. 패키징 된 센서의 감응부의 면적은 $1.2{\times}1.2mm^2$이었다. 센서의 선형성은 오차가 ${\pm}3%$로 우수하였다. 제작된 센서의 분해능은 약 $1{\times}10^{-5}T$였다.

• 대한기계학회논문집A
• /
• 제20권2호
• /
• pp.408-413
• /
• 1996

A self-diagnostic, air-damped, piezoresitive, cantilever-beam microaccelerometer has been designed, fabricated and tested for applications to automotive electronic airbag systems. A skew-symmetric proof-mass has been designed for self-diagnostic capability and zero transverse sensitivity. Two kinds of multi-step anisotropic etching processes are developed for beam thickness control and fillet-rounding formation, UV-curing paste has been used for sillicon-to-glass bounding. The resonant frequency of 2.07kHz has been measured from the fabricated devices. The sensitivity of 195 $\mu{V}$/g is obtained with a nonlinearity of 4% over $\pm$50g ranges. Flat amplitude response and frequency-proportional phase response have been obserbed, It is shown that the design and fabricaiton methods developed in the present study yield a simple, practical and effective mean for improving the performance, reliability as well as the reproducibility of the accelerometers.

• 한국결정성장학회지
• /
• 제21권4호
• /
• pp.164-168
• /
• 2011

고이온밀도 플라즈마 식각에 의한 고종횡비, 고이방성을 갖는 ZnO, $SnO_2$ 나노 구조 가스 감응층 형성을 위하여 mask 재료들과의 식각 선택도를 조사하였다. $25BCl_3$/10Ar ICP 플라즈마에서는 ZnO와 Ni 간 5.1~6.1 범위의 식각 선택도가 확보된 반면에 Al의 경우 효율적인 식각 선택도를 확보할 수 없었다. $25CF_4$/10Ar ICP 플라즈마에서는 ZnO와 Ni 간에 7~17 범위의 높은 식각 선택도를 얻을 수 있었다. $SnO_2$는 $SnF_x$ 식각 생성물의 높은 휘발성에 기인하여 Ni에 비해 매우 높은 식각 속도를 나타내었고, 최고치 약 67의 매우 높은 식각 선택도를 확보하였다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.417-420
• /
• 2007

Micro parts are usually used of producing by micro-electro-mechanical systems(MEMS). In this paper, we present some fundamental results concerning on the MEMS, extrusion condition on the micro forming characteristics and new micro forward extrusion machine has been developed. In the first step, we manufactured micro dies in two kinds of sections. One is a circle section, another is a cross section. The process for fabricating micro dies combines a deep UV-lithography, anisotropic etching techniques and metal electroplating with bulk silicon based on Ni with a thickness of $50{\mu}m$. The outer diameter of Ni-micro dies is 3mm and the diameter of extrusion section is $270{\mu}m$ for a cross section, $500{\mu}m$ for a circle section. The low linear density polyethylene(LLEPD) in the shape of a pellet has been used of micro extrusion. The billet was placed in a container manufactured by electric discharge machining and extruded through the micro die by a piezoelectric actuator. The micro extrusion has succeeded in a forming such micro parts as micro bars, micro cross shafts.