• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.1-12
• /
• 2009

A new mix design procedure for cold in-place recycling using foamed asphalt (CIR-foam) has been developed for Iowa Department of Transportation. Some strengths and weaknesses of the new mix design parameters were considered and modified to improve the laboratory test procedure. Based on the critical mixture parameters identified, a new mix design procedure was developed and validated to establish the properties of the CIR-foam mixtures. As part of the validation effort to evaluate a new CIR-foam mix design procedure, dynamic moduli of CIR-foam mixtures made of seven different reclaimed asphalt pavement (RAP) materials collected throughout the state of Iowa were measured and their master curves were constructed. The main objectives of this study are to provide: 1) standardized testing procedure for measuring the dynamic modulus of CIR-foam mixtures using new simple performance testing (SPT) equipment; 2) analysis procedure for constructing the master curves for a wide range of RAP materials; and 3) impacts of RAP material characteristics on the dynamic modulus. Dynamic moduli were measured at three different temperatures and six different loading frequencies and they were consistent among different RAP sources. Master curves were then constructed for the CIR-foam mixtures using seven different RAP materials. Based upon the observation of the constructed master curves, dynamic moduli of CIR-foam mixtures were less sensitive to the loading frequencies than HMA mixtures. It can be concluded that at the low temperature, the dynamic modulus is affected by the amount of fines in the RAP materials whereas, at the high temperature, the dynamic modulus is influenced by the residual binder characteristics.

• Polymer(Korea)
• /
• v.33 no.5
• /
• pp.501-508
• /
• 2009

The thermal degradation experiment of sodium salt of poly (${\gamma}$-glutamic acid) (PGGNa) has been carried out in both its solid phase and solution phase at the range of $57{\sim}120^{\circ}C$ and their molecular weight decreasing effect was analyzed as a function of time by means of viscometry and light scattering. Based on the solid phase degradation results, it was supposed that the bond scission rate in a polymer chain kept constant and that the bond scission was occurred on a randomly located position in a polymer chain. For the degradation in solution phase, it was also found that all data at various temperatures were dropped on a single master curve when the reduced time $t/t^*$ was used in the plot of the reciprocal intrinsic viscosity (or molecular weight). This degradation curve in solution phase could be expressed as the sum of a single exponential and a linear equation and especially, the single exponential character appeared only at the beginning stage. The activation energy was measured as $107{\sim}115$ kJ/mol in this study and agreed with the literature values.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.51 no.3
• /
• pp.387-395
• /
• 2015

Starfish, a species of Echinoderm, is widely known as a predator on benthic invertebrate. A series of fishing experiments was carried out in the western coastal waters of Korea from September, 2011 to November, 2012, using the drum-shaped pots of different mesh sizes (17.1, 24.8, 35.3, 39.8, and 48.3 mm) to describe the composition of the catch species and the mesh selectivity of the pot for starfish. Some species including fish, crab, and starfish were caught in the experimental pots. The SELECT (Share Each Length's Catch Total) method was applied to describe the selectivity of the pot for starfish Asterina pectinifera. The master selection curve was estimated to be s(R) = exp(10.358R-4.086) / [1+exp(10.358R-4.086)], where R is the ratio of arm length to mesh size. The relative arm length of 50% retention was 0.395, and the selection range was 0.212. The results should be helpful to understand the relationship between the catch size of starfish and the mesh size of pot.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.82-84
• /
• 2005

Fatigue assessment of welded structure is very sensitive to the method of local stress determination. Normally, hot spot stress which is surface stress extracted from 0.5t, 1.5t away from weld toe is widely used to obtain local stress. However, this method has a lot of limitation in the evaluation of fatigue strength. Therefore, mesh has to comply with strict requirements since stress extracted from this method strongly rely on mesh size and element types. And that method does not cover the stress gradient through thickness direction since only surface stress is considered. Recently, new method to obtain local stress is proposed, which is structural stress. This method has an advantage, which is mesh intransitiveness and covering the effect of both bending and axial stress in local area. In this paper, fatigue test data for various welded joints was analyzed to review the reliability of structural stress. As a result, it is verified that S-N curve using structural stress guaranteed single master curve for various joint type and testing condition.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.4
• /
• pp.317-326
• /
• 2017

Comparative fishing experiments were conducted in the eastern coastal waters near Uljin, Korea from 2002 to 2004, using the experimental trammel nets to estimate the selectivity for spinyhead sculpin Dasycottus setiger. The inner panels of the nets were made of nylon monofilament with four mesh sizes (82.2, 89.4, 104.8, and 120.2 mm) while its two outer panels were made of twisted nylon multifilament with a mesh size of 510 mm. The SELECT (Share Each Length's Catch Total) procedure with maximum likelihood method was applied to obtain a master selection curve. The different functional models (normal, lognormal, bi-normal, and logistic model) were fitted to the catch data. The lognormal model with the fixed relative fishing intensity was chosen as the best-fitted selection curve through comparison of model deviance and AIC (Akaike's Information Criterion). The optimum relative length (the ratio of fish total length to mesh size) with the maximum relative efficiency was obtained as 2.492.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.3
• /
• pp.284-291
• /
• 2014

Finely-striate buccinum Buccinum striatissimum, a species of whelks, is caught mainly by pot in the eastern coastal waters of Korea. In order to determine the size selectivity of pot for the species, comparative fishing experiments were conducted near Yeongil Bay from June to September in 2003 using the dome-shaped pots with different five mesh sizes (17.1, 24.8, 35.3, 39.8, and 48.3 mm). The parameters of logistic equation were estimated by the SELECT (Share Each Length's Catch Total) method based on a multinomial distribution. The model with the estimated split parameter was found to fit the catch data best. The master selection curve was estimated to be s (R)=exp (13.044R-16.438)/[1 + exp (13.044R-16.438)], where R is the ratio of shell height to mesh size. The relative shell height of 50% retention was 1.260, and the selection range was 0.168. Enlargement in mesh size of the pot allows more small-sized whelks to escape.

• Nuclear Engineering and Technology
• /
• v.38 no.3
• /
• pp.277-284
• /
• 2006

In order to ensure the structural integrity of nuclear welded structures during design life, the fatigue life has to be evaluated by fatigue analysis procedures presented in technical codes such as ASME B&PV Code Section III. However, existing fatigue analysis procedures do not explicitly consider the presence of welded joints. A new fatigue analysis procedure based on a structural stress/fracture mechanics approach has been recently developed in order to reduce conservatism by erasing uncertainty in the analysis procedure. A recent review of fatigue crack growth data under various mean loading conditions using the structural stress/fracture mechanics approach, does not consider the mean loading effect, revealed some significant discrepancies in fatigue crack growth curves according to the mean loading conditions. In this paper, we propose the use of the stress intensity factor range ${\Delta}K$ characterized with loading ratio R effects in terms of the structural stress. We demonstrate the effectiveness in characterizing fatigue crack growth and S-N behavior using the well-known data. It was identified that the S-N data under high mean loading could be consolidated in a master S-N curve for welded joints.

• Textile Coloration and Finishing
• /
• v.22 no.3
• /
• pp.187-193
• /
• 2010

The effects of molecular weight (MW) and concentration on the rheological properties of poly(vinyl alcohol) (PVA) solutions in dimethyl sulfoxide (DMSO) were investigated at $30^{\circ}C$. Ubbelohde viscometer and rotational rheometer were employed for dilute and concentrated regime, respectively. In the dilute regime, the Mark-Houwink exponent ($\alpha$) of the solutions determined from three different MWs proved 0.73. The critical concentration (C*), in which the entanglement and overlap of polymer molecules began to take place, decreased with increasing the MW of PVA. Huggins constant ($K_H$) values ranged from 0.33 to 0.45 over the MW examined. In the log-log plot of $\eta_{sp}$ versus [$\eta$]C, the PVA with higher degree of polymerization (DP) gave a greater slope exhibiting the inflection point in the vicinity of C*. In the dynamic viscosity ($\eta'$) curve, the PVA solutions of DP 1700 presented Newtonian fluid behavior over most of the frequency range examined. However, the lower Newtonian flow region reduced with increasing the DP. As the PVA concentration increased, $\eta'$ was increased and the onset shear rate for pseudoplasticity was decreased. In the Cole-Cole plot, PVA solutions showed almost a single master curve in a slope of ca. 1.65 regardless of the DP. However, the increase of the concentration from 8 to 12 wt% for PVA solutions of DP 5000 decreased the slope from 1.73 to 1.57. In the tan $\delta$ curve, the onset frequency for sol-gel transition was shifted from 154 to 92 rad/s with increasing the DP from 3300 to 5000 and from 192 to 46 rad/s with increasing the concentration from 8 to 12 wt%. In addition, longer relaxation time ($\lambda$) was observed with increasing the DP and concentration.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.49 no.2
• /
• pp.106-115
• /
• 2013

A series of fishing experiments were carried out in the western coastal waters of Korea from May, 2006 to September, 2007, using gill nets of different mesh sizes (m=101, 121.8, 152.5, 176.8, and 191 mm) to determine the mesh selectivity of gill net for swimming crab, Potunus trituberculatus. The catch species was composed of swimming crab (87%), Thomas's rapa whelk Rapana venosa (5%), arthritic neptune Neptunea cumingi (2%), Japanese swimming crab Charybdis japonica (2%), marbled sole Pleuronectes yokohamae (1%), pen shell Atrina pectinata, ocellate spot skate Okamejei kenojei, and so on. The carapace length (CL) of each swimming crab caught in the experimental nets was measured. Sponge crab (egg-bearing female crab) was appeared from the end of June to August in the coastal waters. The master selection curve was estimated by applying the extended Kitahara's method. The selection curve showed that the gill nets of larger mesh size allowed more crabs of small carapace size to escape. The optimum value (CL/m) was 0.645 and the CL/m was estimated to be 0.301, 0.354, 0.391, 0.422, and 0.450 when the retention probabilities were 0.1, 0.2, 0.3, 0.4 and 0.5, respectively.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.45 no.2
• /
• pp.122-127
• /
• 2009

A series of fishing experiments was carried out in the eastern coastal waters of Korea from January, 2002 to March, 2003, using gill nets of different mesh sizes (m 180, 210, 240, 270 and 300 mm) to determine the size selectivity of gill net for female snow crab, Chionoecetes opilio. The catch of experimental gears was mostly snow crab (97%), Chionoecetes opilio. The maximum carapace length (RL) of each female snow crab caught in the fishing experiments was measured. The master selection curve was estimated by applying the extended Kitahara s method. The selection curve showed that the gill nets of larger mesh size allowed more female crabs of small carapace size to escape. The optimum values of RL/m for 1.0 of retention probability was 0.563 and RL/m was estimated to be 0.249, 0.290, 0.319, 0.344 and 0.367 when the retention probability were 0.1, 0.2, 0.3, 0.4 and 0.5, respectively.