• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.83-85
• /
• 2019

The use of high voltage gain converters is essential for the distributed power generation systems with renewable energy sources such as the fuel cells and solar cells due to their low voltage characteristics. In this paper, a high voltage gain topology combining cascode Inverting Buck-Boost converter and voltage multiplier structure is introduced. In proposed converter, the input voltage is connected in series at the output, the portion of input power is directly delivered to the load which results in continuous input current. In addition, the voltage multiplier stage stacked in proper manner is not only enhance high step-up voltage gain ratio but also significantly reduce the voltage stress across all semiconductor devices and capacitors. As a result, the high current-low voltage switches can be employed for higher efficiency and lower cost. In order to show the feasibility of the proposed topology, the operation principle is presented and the steady-state characteristic is analyzed in detail. A 380W-40/380V prototype converter was built to validate the effectiveness of proposed converter.

• Transactions on Electrical and Electronic Materials
• /
• v.2 no.4
• /
• pp.1-6
• /
• 2001

In this paper, a 1.5 V high-gain high-frequency CMOS complementary operational amplifier is presented. The input stage of op-amp is designed for supporting the constant transconductance on the Input stage by consisting of the parallel-connected rail-to-rail complementary differential pairs. And consisting of the class-AB rail-to-rail output stage using the concept of elementary shunt stage and the grounded-gate cascode compensation technique for improving the low PSRR which was a disadvantage in the general CMOS complementary input stage, the load dependence of open loop gain and the stability of op- amp on the output load are improved, and the high-gain high-frequency operation can be achieved. The designed op-amp operates perfectly on the complementary mode with the 180° phase conversion for a 1.5 V supply voltage, and shows the DC open loop gain of 84 dB, the phase margin of 65°, and the unity gain frequency of 20 MHz. In addition, the amplifier shows the 0.1 % settling time of .179 ㎲ for the positive step and 0.154 ㎲ for the negative step on the 100 mV small-signal step, respectively, and shows the total power dissipation of 8.93 mW.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.14 no.6
• /
• pp.473-478
• /
• 2021

This paper designed a wideband, high gain planar trapezoidal monopole antenna using backside frequency selective surface (FSS) according to the need for wideband and high gain antenna required in various fields such as rapidly increasing wireless communication, autonomous vehicles, 5G wireless communication and wideband applications. The proposed antenna uses a dual metallic to have a structural difference from the existing FSS. By solving the complexity of the design antenna using genetic algorithms (GA) and high frequency structural simulators (HFSS) simulations, the proposed antenna is not only produce a high efficiency but also presents a wide bandwidth of 3.52 to 5.92 GHz and a gain of 10.5 dBi over the entire bandwidth, with the highest gain of 11.8 dBi at 5.1 GHz. It has been confirmed that the gain increased 8.6 dBi as the 36% impedance bandwidth of 1.8 GHz compared to the existing antenna improved to the 50% impedance bandwidth of 2.4 GHz.

• Journal of Navigation and Port Research
• /
• v.34 no.1
• /
• pp.21-26
• /
• 2010

This paper describes patch antenna design method of antenna high gain and broad bandwidth using cylindrical magneto material around feeding line. Strong current induction method applied combination to generate magnetic fields around feeding line for antenna high gain characteristic and principle of PIFA designed application for design of antenna broadband. In case of single CMM, gain increased 3.96 dB compare with the reference antenna gain however bandwidth characteristic not increased compare with the reference antenna. In case of dual CMM, gain improved about 10 dB compare with the reference antenna and -10 below bandwidth is 700 MHz(50 MHz~750 MHz) with this paper designed high gain characteristic.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.444-444
• /
• 2000

For a class of nonlinear systems which satisfy a certain condition so called output feedback exponential passivity (OFEP), it is well known that one can easily design a high-gain output feedback control system. The designed high-gain controller has simple structure and high robustness. However, from the viewpoint of practical application, it is important to consider a robust control scheme for controlled systems for which some of the assumptions of output feedback stabilization are not valid. In this paper. we deal with a design problem of the robust high-gain adaptive output feedback control for the above-mentioned class of nonlinear systems with uncertain nonlinearities and/or disturbances.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.54 no.5
• /
• pp.285-290
• /
• 2005

The state observer is being used widely because it has the advantage of the guarantee of reliability on financial problem, over heating, and physical shock. However, an Luenberger observer and a Sliding observer have such problems that an experimenter needs to know dynamics and parameters of the system. And also, the high gain observer has such a problem that it has transient state at the beginning of the observation. In this paper, the Neuro observer is proposed to improve these problems. The proposed Neuro observer complement a problem that occur from increase of gain of High-gain observer in proportion to the square number of observable state variables. And also, the proposed Neuro observer can tune the gain obtained by differentiating observational error at transient state automatically by using the backpropagation training method to stabilize the observational speed. To prove a performance of the proposed observer, it is simulated that the comparison between the state estimate performance of the proposed observer and that of Sliding, High gain observer is made by using a sinusoidal input to the observer which consists of four layers in stable 2nd order system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.25 no.2
• /
• pp.133-141
• /
• 2020

The use of high-gain-voltage step-up converters for distributed power generation systems is being popularized because of the need for new energy generation and power conversion technologies. In this study, a new constructed high-gain-boost DC-DC converter was proposed to coordinate low voltage output DC sources, such as PV or fuel cell systems, with high DC bus (380 V) lines. Compared with traditional boost DC-DC converters, the proposed converter can create higher gain and has wider input voltage range and lower voltage stress for power semiconductors and passive elements. Moreover, the proposed topology produces multilevel DC voltage output, which is the main advantage of the proposed topology. Steady-state analysis in continuous conduction mode of the proposed converter is discussed in detail. The practicability of the proposed DC-DC converter is presented by experimental results with a 300 W prototype converter.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.6
• /
• pp.853-856
• /
• 2021

In this paper, a low noise amplifier having high gain and low noise by using input and inter stage matching circuits has been designed. A current-reused two-stage common-source topology is adopted, which can obtain high gain and low power consumption. Deterioration of noise characteristics according to the source inductive degeneration matching is compensated by adopting additional matching circuits. Moreover trade-offs among noise, gain, linearity, impedance matching, and power dissipation have been considered. In this design, 0.18-mm CMOS process is employed for the simulation. The simulated results show that the designed low noise amplifier can provide high power gain and low noise characteristics.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.1B
• /
• pp.8-14
• /
• 2000

This paper analyzes and accesses the gain of optically pumped surface-normal MQW optical amplifiers. The proposed amplifiers have the advantage of polarization independence, high coupling efficiency to and from optical fibers, and flexibility of operating wavelength. We analyzed the gain characteristics of 100 - 200-period MQWs and verified the dependence of a strained lattice and selective doping. Theoretical analysis of such MQWs showsa single-pass gain of 3 dB with broad operation bandwidth. A single-pass gain of 2.6 dB is obtained experimentally in an InGaAs/InGaAlAs MQW amplifier, which is compared with calculations. The use of Fabry-Perot interferometer (FPI) structure in an optical amplifier is a useful way to increase the gain, but causes a problem of narrow operation bandwidth when the single-pass gain is low. Therefore, a single-pass gain above 2to 3 dB is a prerequisite to achieve both a high gain and moderate operation bandwidth in FPI-structured opticalamplifiers. We have designed an FPI-structured surface-normal optical amplifier both with a high gain of broad operation bandwidth of 4.6mm, when a single-pass gain is 3 dB.

• Journal of electromagnetic engineering and science
• /
• v.14 no.2
• /
• pp.47-53
• /
• 2014

This paper presents a high gain and high harmonic rejection low-noise amplifier (LNA) for software-defined radio receiver. This LNA exploits the high quality factor (Q) series resonance technique. High Q series resonance can amplify the in-band signal voltage and attenuate the out-band signals. This is achieved by a source impedance transformation. This technique does not consume power and can easily support multiband operation. The chip is fabricated in a $0.13-{\mu}m$ CMOS. It supports four bands (640, 710, 830, and 1,070MHz). The measured forward gain ($S_{21}$) is between 12.1 and 17.4 dB and the noise figure is between 2.7 and 3.3 dB. The IIP3 measures between -5.7 and -10.8 dBm, and the third harmonic rejection ratios are more than 30 dB. The LNA consumes 9.6 mW from a 1.2-V supply.