• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.588-591
• /
• 2004

Generally, $TiO_2$ powders absorb ultraviolet rays and make oxidation/reduction reactions on its surface. Hydroxide radical(OH), a product of photocatalyst reactions, has so strong oxidation/reduction electric potential that it can oxidize noxious gas like VOCs(Volatile Organic Compounds) and NOx. In this study, $TiO_2$ was substituted for exposed concrete to investigate the purifying degree of VOCs(Benzene, Toluene) and NOx. Anatase types of $TiO_2$ were used as photocatalyst. The sun rays and the ultraviolet were used as a light source. Anatase type $TiO_2$ was better than rutile type in purifying performance. The sunray showed the best purifying performance among the light sources. $3\%$ substitution of $TiO_2$ with the sunray was enough to purify VOCs(Benzene, Toluene) and NOx efficiently.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2006.05a
• /
• pp.147-153
• /
• 2006

Photocatalyst reaction has limit of its usage because application range mostly centered on atmosphere purification area. Thus, it is true that an alternative plans are necessary to increase usage of $TiO_2$ as photocatalyst material. (1) The result of flow felt according to $TiO_2$ replacement rate has shown that both of anatase type and rutile type over 12% deviated from desired flow, $110{\pm}5mm$. Consequently, the range below 9% will be suitable when the anatase type $TiO_2$ if used for functional additives if workability is considered. (2) After compressive strength test, replacement rate 6-9% is estimated as suitable range if $TiO_2$ is used as compressive strength material. Rutile type and anatase type are suitable for in early-age strength and long-age strength respectively. (3) It was revealed that bending strength was dramatically decreased when replacement rate was increased. The main reason were the increase of $TiO_2$ doesn't influence hydration reaction and the decrease of bending strength. (4) The result from the water purification properties test using ion-chromatograhpy has shown that the condition with anatase type $TiO_2$ was normally better than rutile type on the same replacement rate.

• Rapid Communication in Photoscience
• /
• v.4 no.1
• /
• pp.9-11
• /
• 2015

The debromination of phenethyl bromide by the $B_{12}-TiO_2$ hybrid catalyst under UV light irradiation was investigated. The catalytic efficiency was dependent on the type of $TiO_2$. The anatase form of $TiO_2$ was superior to the rutile form of $TiO_2$. The selectivity of the product was also dependent on the crystal structure of $TiO_2$, and the rutile form of $TiO_2$ showed a high selectivity for the formation of the coupling product, 2,3-diphenylbutane, when compared to that of the anatase form of $TiO_2$.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.4
• /
• pp.204-212
• /
• 1993

The preparation of $TiO_2$ fine particles from $TiCl_4$ and oxygen by the vapor-phasereaction was investigated at $850^{\circ}C$ with an emphasis on the effect of its experimental conditions on the crystal type of the products. Anatase $TiO_2$ particles prepared by experiment were used to study anatase-rutile transition by calcination temperature, the additives and gas atmosphere. The results were as follows. The kinetics of anatase-rutile transition was well agreed with A vrami equation, and the activation energy of transition was 35kcal/mol. The addition of CuO in anatase $TiO_2$ particles accelerated the anatase-rutile transition, and its transition was retarded in vaccum.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.33-36
• /
• 2014

This study was aimed at synthesizing and characterizing cerium-doped titania. Cerium-doped anatase titania powders were prepared by sol-gel process, with ammonium (IV) nitrate and titanium (IV) butoxide as the raw materials. The characteristics of pure $TiO_2$ and cerium-doped $TiO_2$ were investigated by XRD, TG/DTA, FE-SEM, and UV-vis spectroscopy. The results of this study show that anatase type of $TiO_2$ was obtained in as-prepared and calcined $TiO_2$ and Ce-$TiO_2$ powder. A DTA curve was also observed as the crystallization temperature decreased with increasing cerium contents. We found that the crystallite size of the obtained anatase particles decreased from 55 nm to 25 nm and the particle size decreased with increasing cerium contents. Moreover, UV-vis spectra showed that anatase titania powders with various cerium contents effectively extend the light absorption properties to the visible region.

• Journal of the Korean Magnetics Society
• /
• v.16 no.1
• /
• pp.45-50
• /
• 2006

Oxygen-deficient anatase and rutile titanium dioxide $(TiO_{2-\delta})$ thin films were prepared by a sol-gel method and their structural, electronic, and magnetic properties were investigated. Both anatase and rutile $TiO_{2-\delta}:Fe$ Fe films exhibited ferromagnetism at room temperature for a limited range of Fe doping. For the same amount of Fe doping, the anatase sample exhibited a higher magnetic moment than the rutile one. Result of conversion electron Mossbauer spectroscopy measurements indicates that $Fe^{3+}$ ions substituting the octahedral $Ti^{4+}$ sites mainly contribute to the room-temperature ferromagnetism. Some of the anatase $TiO_{2-\delta}:Fe$ films exhibited p-type character but the observed feromagnetism turns out to be independent of the hole concentration. The room-temperature ferromagnetism can be explained in terms of a direct ferromagnetic coupling between two neighboring $Fe^{3+}$ ions via an electron trapped in oxygen vacancy in $TiO_{2-\delta}:Fe$.

• Analytical Science and Technology
• /
• v.14 no.1
• /
• pp.15-20
• /
• 2001

Photocatalytic $TiO_2$ films were prepared by anodic oxidation at 180 V and their structural difference caused by oxidation conditions was studies. The microstructure of $TiO_2$ films in $H_2SO_4$ and $H_2SO_4/H_2O_2$ solution was mixed type of rutile and anatase. However, the $TiO_2$ layer formed in $H_2SO_4/H_3PO_4$ and $H_2SO_4/H_3PO_4/H_2O_2$ mixture was mostly anatase type. All $TiO_2$ films prepared by anodic oxidation exhibited photocatalytic properties. The photocatalytic degradation of aniline blue was first order reaction with similar rate constants at all oxidative conditions examined in this work.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.9 no.5
• /
• pp.510-515
• /
• 1999

Synthesize of anatase type $TiO_2$ from $TiCl_4$ solution was studied. KOH was used on dehydration reaction of $TiCl_4$ solution. Products of dehydration reaction was calcined at 300, 500, 700, 900, $1000^{\circ}C$ during 1hour. Calcined products was studied by XRD, DTA, and FT-IR for effect of calcined temperature. The results are as follow. \circled1 Product pf dehydration reaction at$ 90^{\circ}C$ was semicrystalline anatase type $TiO_2$ because it has a peak vary broad and low at the position of anatase crysral XRD pattern. \circled2 Pure titanium oxide semi-crystalline products were produced at acid pH condition which convert to anatase crystal at $300^{\circ}C$ and to rutile crystal at $700^{\circ}C$. \circled3 The chemical composition of semicrystalline products which was produce at alkali pH conditions, were potasium titante. Potasium-titanate semi-crystalline products crystallized at 630~$640^{\circ}C$ \circled4 The transition temperature of potassium dopped titanium oxide semi-crystalline products was increased with the contents of potasium. \circled5 The optimum synthesise condition of anatase $TiO_2$ products from $TiCl_4$ and KOH are pH 3~5 and $300^{\circ}C$ calcination.

• Journal of Powder Materials
• /
• v.23 no.1
• /
• pp.33-37
• /
• 2016

10 wt.% and 20 wt.%$Li-TiO_2$ composite powders are synthesized by a sol-gel method using titanium isopropoxide and $Li_2CO_3$ as precursors. The as-received amorphous 10 wt.%$Li-TiO_2$ composite powders crystallize into the anatase-type crystal structure upon calcination at $450^{\circ}C$, which then changes to the rutile phase at $750^{\circ}C$. The asreceived 20 wt%$Li-TiO_2$ composite powders, on the other hand, crystallize into the anatase-type structure. As the calcination temperature increases, the anatase $TiO_2$ phase gets transformed to the $LiTiO_2$ phase. The peaks for the samples obtained after calcination at $900^{\circ}C$ mainly exhibit the $LiTiO_2$ and $Li_2TiO_3$ phases. For a comparison of the photocatalytic activity, 10 wt.% and 20 wt.% $Li-TiO_2$ composite powders calcined at $450^{\circ}C$, $600^{\circ}C$, and $750^{\circ}C$ are used. The 20 wt.%$Li-TiO_2$ composite powders calcined at $600^{\circ}C$ show excellent efficiency for the removal of methylorange.

• Applied Chemistry for Engineering
• /
• v.17 no.5
• /
• pp.561-564
• /
• 2006

$SnO_{2}$-doped anatase type $TiO_{2}$ powder was prepared by the polymerization complex route from tin(IV) bis (acetylacetonate) dichloride, titanium diisopropoxide bis (acetylacetonate) and polyethylene glycol (PEG) as a complexing agent. The structural changes of reaction mixture were monitored by fourier transform infarared (FT-IR) spectroscopy. The microstructure and morphology of gel powder were studied by field-emission scanning electron microscopy (FE-SEM) and X-ray diffractometry (XRD). The photocatalytic activity of these powders with the anatase structure was investigated by using indigo carmine solution.