• Journal of Life Science
• /
• v.5 no.2
• /
• pp.20-20
• /
• 1995

The aroma components of commercial green teas picked inAugust were collected and identified. The extract of aroma compounds in green tea were accoimplished by a modified rotary evaporation. The concentrated wxtracts were analyzed and identified by GC and GC-MS. In GC analysis, T$_{R}$ value of GC represented bt KI value which standardized. The most abundant components of green teas picked in August were 1-Penten-3-ol, trans, trans-2, 4-heptadienal, linalool, $\beta$-ionone and nerolidol.

• Journal of Life Science
• /
• v.5 no.2
• /
• pp.76-80
• /
• 1995

The aroma components of commercial green teas picked inAugust were collected and identified. The extract of aroma compounds in green tea were accoimplished by a modified rotary evaporation. The concentrated wxtracts were analyzed and identified by GC and GC-MS. In GC analysis, T$_{R}$ value of GC represented bt KI value which standardized. The most abundant components of green teas picked in August were 1-Penten-3-ol, trans, trans-2, 4-heptadienal, linalool, $\beta$-ionone and nerolidol.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.7
• /
• pp.69-74
• /
• 2014

Recently, IEC published new standards about the requirements and tests for lightning protection system(LPS) components. If components are used for LPS, they should comply with the IEC standards. This paper, we collected six specimens for the metallic connection components using in domestic, and it tested for withstand lightning current which according to the IEC 62561-1. As a result, only one specimen meet this performance requirement. The specimen is the metallic connection component with four bolts fixed. Therefor, when designing of LPS in domestic, the metallic connection components shall be taken into account for the selection of the withstand lightning current. In addition, we need to develop for LPS components product and the national standards.

• Journal of Information Technology Services
• /
• v.5 no.1
• /
• pp.149-164
• /
• 2006

The companies are trying to apply to software development approach by utilizing open-source components. The open-source components are new alternatives to solve limits of the previous software developments such as quality of software, time and cost of development. Accordingly, various analysis of open-source components were performed. However, the researches about the detailed procedures and methods to utilize open-source components in practical industry are immature. In this paper, we propose the procedures and cases for identifying, validating, selecting of suitable open-source components and for applying to change and modification. Proposed procedures and cases will be a great contribution to spread of utilizing the open-source.

• Journal of Ginseng Research
• /
• v.20 no.3
• /
• pp.284-290
• /
• 1996

To Identify phenolic components known to exist in Korean ginseng (Panax ginseng C.A. Meyer) by GC/MS, three derivatization methods were employed for their analyses. First, phenolic components in ether soluble acidic fraction prepared from Korean red ginseng powder were taimethylsilylated. Secondly, phenolic acids in the same fraction were esterified with diazomethane followed by trlmethylsilylation. Thirdly, acidic components in ginseng powder were extracted and esterified concurrently by methanolic sulfuric acid, followed by fractionation of phenolic components with Silica Sep-Paka and trimethylsilylatlon. All phenolic components found in ginseng except gen tisic acid were identified by retention times and mass spectrums of standards. Besides, 5 phenolic components including salicyl alcohol and 1-H-indole-2-carboxylic acid were first identified from Korea an red ginseng by GC/MS.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.6_2
• /
• pp.1103-1110
• /
• 2022

The old machine tools that have been used for a long time cause both increase in defective rate and decrease in productivity compared to new machines due to wear and failure of their components. In order to improve productivity and quality of machined components through remanufacturing, it is necessary to analyze the wear and failure of major components of old machine tools. In this study, the process for reverse engineering is designed for the remanufacture of planner millers, which belong to a very large machine tool. Also, the suitability of the designed process is verified through the analysis of the selected remanufactured components. In the first step of the process, some major components of the aging planner miller are scanned using a 3D laser scanner. In the next step, reverse engineering is performed using the data obtained through 3D scanning. Finally, wear and failure analysis is performed by comparing the reverse engineering data with the scan data. As a result, this reverse design and wear analysis can complement the insufficient design database and reduce costs in the maintenance of remanufactured products.

• Korean Journal of Applied Biomechanics
• /
• v.25 no.2
• /
• pp.157-165
• /
• 2015

Object : The goals of this research were to make Performance Enhanced Model(PE) taken the largest performance index (PI) through artificial variation of principle components calculated by principle component analysis for trial data, and to verify the effect through comparing kinematic factors between trial data (Raw) and PE. Method : Ten subjects (5 men, 5 women) were recruited and 80% of their maximal record was considered. The PI is a regression equation. In order to develop PE, we extracted Principle components from trial position data (by Principle Components Analysis (PCA)). Before PCA, we made 17 position data to 3 row matrix according to components. We calculated 3 eigen value (principle components) through PCA. And except Y (medial-lateral direction) component (because motion of Y component is small), principle components of X (anterior-posterior direction) and Z (vertical direction) components were changed as following. Changed principle components = principle components + principle components ${\times}$ k. After changing the each principle component, we reconstructed position data using the changed principle components and calculated performance index (PI). A Paired t-test was used to compare Raw data and Performance Enhanced Model data. The level of statistical significance was set at $p{\leq}0.05$. Result : The PI was significantly increased about 12.9kg at PE ($101.92{\pm}6.25$) when compared to the Raw data ($91.29{\pm}7.10$). It means that performance can be increased by optimizing 3D positions. The difference of kinematic factors as follows : the movement distance of the bar from start to lock out was significantly larger (about 1cm) for PE, the width of anterior-posterior bar position in full phase was significantly wider (about 1.3cm) for PE and the horizontal displacement toward the weightlifter after beginning of descent from maximal height was significantly greater (about 0.4cm) for PE. Additionally, the minimum knee angle in the 2-pull phase was significantly smaller (approximately 2.7cm) for the PE compared to that of the Raw. PE was decided at proximal position from the Raw (origin point (0,0)) of PC variation). Conclusion : PI was decided at proximal position from the Raw (origin point (0,0)) of PC variation). This means that Performance Enhanced Model was decided by similar motion to the Raw without a great change. Therefore, weightlifters could be accept Performance Enhanced Model easily, comfortably and without large stress. The Performance Enhance Model can provide training direction for athletes to improve their weightlifting records.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.15 no.4
• /
• pp.129-142
• /
• 2013

Fabrics created unique features through the change in various ways depending on the elements including fabric structure, threads, thickness, weaving, patterns and processing. This study examined the difference between texture and image depending on components of fabrics. In order to understand the trend of components of fabrics, the actual components of fabrics was analyzed by year, using the women's apparel trend books, Nelly Rodi Fabrics and Promostyl Fabrics. This study analyzed Spring/Summer season and Fall/Winter season from 2002 to 2012. Frequency analysis, cross-tabulation analysis, multiple response cross tabulation analysis were implemented using SPSS 18.0. The followings are the analysis results. For fabric composition, Spring/Summer season used cotton fabric the most. Cotton fabric accounted for relatively high usage in 2005, 2007 and 2008. Fall/Winter season used wool the most in 2002, 2003, 2004 and 2005. In case of fiber blend by fabric composition, cotton was blended with other fibers in Spring/Summer season except wool. The fiber blending ratio of wool was the highest in Fall/Winter season. Wool was blended in most fabrics. More than two patterns were mixed for fabric patterns. The fabric patterns were applied the most in 2012. For fabric processing, the fabrics by sensitivity-functional processing were continuously used every year and the surface finish showed relatively high usage in 2002 and 2011. In conclusion, this study will build the systematic data for 11 years including fabric trends in the past. It can improve specialization, systematization and efficiency in fabric planning.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.13 no.1
• /
• pp.88-93
• /
• 2004

In general, a fundamental structural design consideration for an automobile is the overall dynamic behavior in bending and torsion. Dynamic behavior of the automobile are mainly influenced by the structural stiffness of B.I.W.(body-in-white) and the physical property of trim components. In this paper, the modeling techniques for various trim components of middle-sized bus are presented, and the dynamic effects of the trim components on the vibration characteristics of the bus are investigated. The $1^{st}$ torsional frequency is decreased by attaching windshield and backlite to the B.I.W., but the $1^{st}$ vertical bending frequency and the $1^{st}$ lateral bending frequency are increased. The natural frequencies of the bus are decreased by attaching doors and windows. And also, the natural frequencies of the bus are large decreased by attaching seats, instrument panel etc. The study shows that the dynamic characteristics of the bus can be effectively predicted in the initial design stage.

• Korean Institute of Interior Design Journal
• /
• v.14 no.2 s.49
• /
• pp.120-127
• /
• 2005

The purpose of this study was to examine preferential unit planning components of high-rise residential buildings across family life cycle stages. The questionnaire survey was adopted in this study, and 110 cases were used for data analysis. Based on the age of the oldest child, the family life cycles used in the study were divided into four stages: early childhood, elementary school, adolescence, and adulthood. The findings showed that the preference of the unit planning components across the stages was distinct; families in the stage of early childhood and adolescence had the growing needs for spatial features, and regarded living-related features as important. Families in the stage of adulthood tended to have larger spaces. It was noticed that unit planning components needed to be more differential when the combined effect of both family life cycle stages and housing size was considered.