• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.481-488
• /
• 1998

In recently, lots of researcher have been attached to develope various alternative fuels and to use renewable fuels for solution of the exhaust emission problems. In this study, the usability of used vegetable oil as alternative fuel for diesel engines has been investigated. This paper was compared with the exhaust emissions and performance in diesel engine with used vegetable oil and conventional diesel fuel. Since the vegetable oil includes oxygen of about 10%, it influenced the combustion process strongly. So, the smoke emissions of used vegetable oil were exhausted to be lower than those of diesel fuel. Also, the used vegetable oil was much the same cycle to cycle variation with diesel fuel except $P_{(dP}$d.theta.)max/, but the cycle to cycle variation of used vegetable oil was reduced significantly by preheating of the fuel and swirling of the intake air. It was concluded that used vegetable oil could be utilized effectively as renewable fuel for diesel engine.e.

• 한국폐기물자원순환학회지
• /
• 제35권8호
• /
• pp.721-730
• /
• 2018

We investigated the effects of heavy metals in cement in the last 3 years and the amount of waste in the cement manufacturing process. The result shows that the average $Cr^{6+}$ content in cement products is controlled at 10 mg/kg. Cu and Pb have lower detection tendency in white cement than in ordinary portland cement. In addition, heavy metals such as Cd show a certain level of detection regardless of the input wastes. Copper slag and phosphate gypsum are the main influencing factors on the heavy metals in cement products. In auxiliary fuels, plastics waste and wood waste are considered to affect heavy metals in cement products. Alternative raw materials are considered to be affected by the alternative raw materials managed as byproducts. In the case of supplementary fuels, auxiliary fuels managed as waste instead of auxiliary fuels managed as byproducts affect the heavy metals in cement. This study examined the input amount without considering the heavy metals in each waste. Therefore, the result may vary in different situations, and further research must be conducted to supplement the findings. However, if the heavy-metal contents in the waste are constant, it can be used as a reference material for the control of heavy metals in cement products.

• International Journal of Automotive Technology
• /
• 제8권3호
• /
• pp.275-281
• /
• 2007

GTL (Gas To Liquid) has the potential to be used in diesel engines as a clean alternative fuel due to advantages in emission reduction, particularly soot reduction. Since the physical properties of GTL fuel differ from those of diesel fuel to some extent, studying how this difference in characteristics of GTL and diesel fuels affects spray and combustion in diesel engines is important. In this study, visual investigation of sprays and flames from GTL and diesel fuels in a vessel simulating diesel combustion was implemented. The effects of various parameters and conditions, such as injection pressure, chamber temperature and pilot injection on liquid-phase fuel length and auto-ignition delay were investigated. It was determined that GTL has a somewhat shorter liquid-phase fuel length, which explains why there is less contact between the fuel liquid-phase and flame for GTL fuel compared to diesel fuel.

• 한국분무공학회지
• /
• 제18권4호
• /
• pp.169-175
• /
• 2013

Hydrotreated biodiesel (HBD) would be one of the promising alternative fuels instead of current biodiesel. In this study, spray characteristics in terms of spray penetration and spray angle were conducted experimentally including calculated SMDs as well. The ambient pressures of 1, 3, and 5 MPa and injection pressures of 30, 80, and 130 MPa were introduced and the fuels employed were petro-diesel, and 2, 10, 20, 30, and 50% for hydrotreated biodiesel, respectively. The result of this study found that the more HBD blended diesels have the slightly shorter spray tip penetration lengths especially on the lowest injection pressure and at the highest ambient pressure, but have the larger spray angles and SMDs than petro-diesel. Consequently, this study found that HBD has a little bit merits and demerits of macro- and micro- spray patterns compared to petro-diesel.

• 한국수소및신에너지학회논문집
• /
• 제27권6호
• /
• pp.721-726
• /
• 2016

Alcohols are particularly attractive as alternative fuels because they are a renewable resource. This paper describes the performance and emission characteristics of ethanol and diesel blended fuels in a compression ignition engine. This experimental results showed that ethanol diesel blended fuels decreased the torque and brake mean effective pressure. And experimental results indicated that using ethanol-diesel blended fuel, smoke, CO and HC emissions decreased as a result of the ethanol addition.

• 대한기계학회논문집B
• /
• 제28권1호
• /
• pp.99-108
• /
• 2004

Fundamental combustion characteristics, such as the combustion potential, burning velocity and flame stability, for the practical utilization of LFG(Landfill gas) and LFG-blended fuels were experimentally investigated. The combustion potentials(CP) of LFG-blended fuels calculated from the previously suggested formulae were compared with burning velocities obtained by present experiments. The results showed that the previous formulae fur CP of LFG-blended fuels were not agreed with the experimental burning velocity, and these formulae should be revised. To provide an useful information needed to design the combustion devices, a triangular diagram was suggested for the maximum burning velocity of the mixture of CH$_4$, LPG and LFG. From the investigation of the burning velocity and the flame stability in a practical combustor, it was noted that the LFG-blended fuels, of which heating values or Wobbe indices were adjusted to that of natural gas, could be used as an alternative fuel of natural gas.

• 한국분무공학회지
• /
• 제27권4호
• /
• pp.181-187
• /
• 2022

For carbon neutrality, direct-injection hydrogen engines are attracting attention as a future power source. It is essential to estimate the transient injection rate of hydrogen for the optimization of hydrogen injection in direct injection engines. However, conventional injection rate measurement techniques for liquid fuels based on the injection-induced fuel pressure change in a test section are difficult to be applied to gaseous fuels due to the compressibility of the gas and the sealing issue of the components. In this study, a momentum flux measurement technique is introduced to obtain the transient injection rate of gaseous fuels using a force sensor. The injection rate calculation models associated with the momentum flux measurement technique are presented first. Then, the volumetric injection rates are estimated based on the momentum flux data and the calculation models and compared with those measured by a volumetric flow rate meter. The results showed that the momentum flux measurement can detect the injection start and end timings and the transient and steady regimes of the fuel injection. However, the estimated volumetric injection rates showed a large difference from the measured injection rates. An alternative method is suggested that corrects the estimated injection rate results based on the measured mean volumetric flow rates.

• 한국건설순환자원학회논문집
• /
• 제9권1호
• /
• pp.75-84
• /
• 2021

본 연구에서는 시멘트 제조공정에서 연료로 사용된 가연성 산업부산물 및 생활폐기물 대체연료 사용량과 시멘트 품질 중에서도 화학성분, 광물조성, 압축강도간의 상관관계를 확인하고자 하였다. 이를 위해 천연연료로서 유연탄, 대체연료로서 연질 플라스틱류(비닐류 등 풍력에 의해 비산되기 쉬운 성질의 플라스틱류), 경질 플라스틱류(이물질이 혼입되거나, 폐고무, PP 등 풍력에 비산되지 않는 성질의 플라스틱류), 재생유를 사용하는 국내 A시멘트 제조사 소성설비의 2017~2019년 3년간의 연료투입량을 독립변수로 하고, 시멘트 품질 데이터를 종속변수로 하여 요인 회귀분석을 이용한 분석을 실시하였다. 분석결과 대체연료의 종류 및 품질에 따라서는 화학성분(염소 및 LSF) 및 광물조성(f-CaO, C3S량)에 유의한 영향을 미치지 않았으며, 시멘트 압축강도를 저하할 것이라는 우려와는 달리 대체연료 사용량과 시멘트 압축강도간에 유의한 양의 상관관계가 성립하는 것으로 분석되었다.

• 한국건설순환자원학회지
• /
• 제14권1호
• /
• pp.17-21
• /
• 2019

• Asian Journal of Atmospheric Environment
• /
• 제7권1호
• /
• pp.48-55
• /
• 2013

The purpose of this study was to develop a $CO_2$ emission factor for refuse plastic fuel (RPF) combustion facilities, and calculate the $CO_2$ emissions from these facilities. The $CO_2$ reduction from using these facilities was analyzed by comparing $CO_2$ emission to facilities using fossil fuels. The average $CO_2$ emission factor from RPF combustion facilities was 59.7 Mg $CO_2$/TJ. In addition, fossil fuel and RPF use were compared using net calorific value (NCV). Domestic RPF consumption in 2011 was 240,000 Mg/yr, which was compared to fossil fuels using NCV. B-C oil use, which has the same NCV, was equal to RPF use. In contrast, bituminous and anthracite were estimated at 369,231 Mg/yr and 355,556 Mg/yr, respectively. In addition, the reduction in $CO_2$ emissions due to the alternative fuel was analyzed. $CO_2$ emissions were reduced by more than 350 Mg $CO_2$/yr compared to bituminous and anthracite. We confirmed that using RPF, an alternative fuel, can reduce $CO_2$ emissions.