• 한국재료학회지
• /
• 제11권11호
• /
• pp.972-977
• /
• 2001

It was investigated the effect of ultrasonic treatment on magnetic property of ultra fine magnetic Fe powders ($\alpha$-Fe) for magnetic tape. The properties were characterized with vibrating sample magnetometer (VSM), particle size analyzer (PSA) and scanning electron microscope (SEM). At 4hours ultrasonic treatment of 70 kHz, magnetic properties such as squareness ratio (S.Q. : 0.8868), orientation ratio (O.R. : 2.45) and switching field distribution (S.F. D. : 0.394) before taping were relatively enhanced. Cumulative particle size distribution of less than 5$\mu\textrm{m}$ fine powder was above 90% below 1 hour leaving time after ultrasonic treatment and it was supposed that ultrasonic treatment prevent aggregation. The magnetic values of S.Q. and S.F.D. of tape manufactured at 70 kHz and 4hour ultrasonic treatment were improved from 0.7747, 0.3818 to 0.8037, 0.3706, respectively. Electro-magnetic property used as in-output signal characteristic was improved, which showed that ultrasonic treatment developed the magnetic properties.

• Elastomers and Composites
• /
• 제24권4호
• /
• pp.276-289
• /
• 1989

This study deals with both effects of inorganic fillers to vulcanized rubbers such as NR, CR, EPDM, NBR & SBR and inorganic characteristics of domestic fillers in comparision with hard clay produced in the USA. The results were as follows. 1. Main ingredient of domestic clay "Ha-dong clay" was Halloysite, "No-ha Island" was Pyrophyllite with $\alpha$-Quartz, and both of "Hard clay" & "Hwa-soon clay" were proved to be Kaolinite by XRD, DT-TGA and chemical analysis by XRF. 2. Tensile strength value of SBR compounded with these fillers, was Hard clay $146kg\;f/cm^2$, Kaolinite $123kg\;f/cm^2$, Pyrophyllite $82kg\;f/cm^2$, Halloysite $80kg\;f/cm^2$, precipitated $CaCO_3\;27kg\;f/cm^2$, and ground $CaCO_3$ was $21kg\;f/cm^2$. These results showed the increase of seven times according to filler species. 3. The physical properties of non-crystalline rubbers, such as SBR, NBR & EPDM, compared with NR & CR, have been considerably changed according to crystalline phase, particle size, shape and surface structure of fillers. Especially, tensile strength value in case of SBR & EPDM, was differentiated about 1.5 times by the particle size of fillers. 4. In SBR, physical properties of rubber compounded with Kaolinite which was surface treated with fatty acid and silane, almost approach to the value of hard clay. 5. Delayed cure time of Kaolinite and decrease of rubber properties by $CaCO_3$ can be improved by blending kaolinite & $CaCO_3$ in the ratio of 2:1.

• 해양환경안전학회:학술대회논문집
• /
• 해양환경안전학회 2006년도 추계학술발표회
• /
• pp.265-269
• /
• 2006

파랑에 의한 선박의 횡동요를 방지하는 감요장치는 크게 수동식과 능동식 으로 분류할 수 있으며 수동형 감요수조는 선박에서 가장 널리 사용되고 있다. 이 연구에서는 감요장치의 하부덕트유동에 관한 기초연구로서 덕트의 제어 댐퍼와 유입부의 유통에 대해 입자영상 유속측정장치를 이용하여 속도벡터분포에 관한 정량적인 데이터를 확보하였다. 그 결과 실험관 벽면에서 측정 된 압력의 분포는 디스크가 전개 상태인 0 도에서 45도까지는 입구 압력은 일정한 상태로 거의 변화하지 않았으나 약 60도 이상에서부터 압력 상승과 점차 급격한 변동현상이 나타났다.

• 한국재료학회지
• /
• 제20권9호
• /
• pp.451-456
• /
• 2010

A promising candidate material for a $H_2$ permeable membrane is SiC due to its many unique properties. A hydrogen-selective SiC membrane was successfully fabricated on the outer surface of an intermediate multilayer $\gamma-Al_2O_3$ with a graded structure. The $\gamma-Al_2O_3$ multilayer was formed on top of a macroporous $\alpha-Al_2O_3$ support by consecutively dipping into a set of successive solutions containing boehmite sols of different particle sizes and then calcining. The boehmite sols were prepared from an aluminum isopropoxide precursor and heated to $80^{\circ}C$ with high speed stirring for 24 hrs to hydrolyze the precursor. Then the solutions were refluxed at $92^{\circ}C$ for 20 hrs to form a boehmite precipitate. The particle size of the boehmite sols was controlled according to various experimental parameters, such as acid types and acid concentrations. The topmost SiC layer was formed on top of the intermediate $\gamma-Al_2O_3$ by pyrolysis of a SiC precursor, polycarbosilane, in an Ar atmosphere. The resulting amorphous SiC-on-$Al_2O_3$ composite membrane pyrolyzed at $900^{\circ}C$ possessed a high $H_2$ permeability of $3.61\times10^{-7}$ $mol{\cdot}m^{-2}{\cdot}s^{-1}{\cdot}Pa^{-1}$ and the $H_2/CO_2$ selectivity was much higher than the theoretical value of 4.69 in all permeation temperature ranges. Gas permeabilities through a SiC membrane are affected by Knudsen diffusion and a surface diffusion mechanism, which are based on the molecular weight of gas species and movement of adsorbed gas molecules on the surface of the pores.

• The Journal of Advanced Prosthodontics
• /
• 제5권3호
• /
• pp.234-240
• /
• 2013

PURPOSE. This study evaluated the effectiveness of various methods for removing provisional cement from implant abutments, and what effect these methods have on the retention of prosthesis during the definitive cementation. MATERIALS AND METHODS. Forty implant fixture analogues and abutments were embedded in resin blocks. Forty cast crowns were fabricated and divided into 4 groups each containing 10 implants. Group A was cemented directly with the definitive cement (Cem-Implant). The remainder were cemented with provisional cement (Temp-Bond NE), and classified according to the method for cleaning the abutments. Group B used a plastic curette and wet gauze, Group C used a rubber cup and pumice, and Group D used an airborne particle abrasion technique. The abutments were observed using a stereomicroscope after removing the provisional cement. The tensile bond strength was measured after the definitive cementation. Statistical analysis was performed using one-way analysis of variance test (${\alpha}$=.05). RESULTS. Group B clearly showed provisional cement remaining, whereas the other groups showed almost no cement. Groups A and B showed a relatively smooth surface. More roughness was observed in Group C, and apparent roughness was noted in Group D. The tensile bond strength tests revealed Group D to have significantly the highest tensile bond strength followed in order by Groups C, A and B. CONCLUSION. A plastic curette and wet gauze alone cannot effectively remove the residual provisional cement on the abutment. The definitive retention increased when the abutments were treated with rubber cup/pumice or airborne particle abraded to remove the provisional cement.

• 한국결정성장학회지
• /
• 제6권3호
• /
• pp.463-470
• /
• 1996

알파 알루미나와 철이 첨가된 티타니아 최종층으로 구성된 세라믹 여과막을 졸-겔방법으로 제조하였다. 철이 첨가된 지지 티타니아 복합여과막은 지지체를 혼합졸에 침지하여 제조하였다. 복합여과막을 $550^{\circ}C$에서 $850^{\circ}C$까지 열처리온도에 따르는 미세구조 변화를 주사전자현미경으로 조사하였다. $650^{\circ}C$에서 1시간 소결한 경우, 철이 첨기된 티타니아 복합여과막의 평균입자 크기는 약 40 nm이었다. 철이 첨가된 티나니아 복합여과막은 티타니아 복합여과막보다 열적 저항성이 우수하였다. 철이 첨가된 티타니아 복합여과막은 $650^{\circ}C$까지 균열이 없는 미세구조와 좁은 입도분포를 유지하였다.

• The Journal of Advanced Prosthodontics
• /
• 제6권4호
• /
• pp.272-277
• /
• 2014

PURPOSE. The purpose of this study was to investigate the impact of different surface treatment methods and thermal ageing on the bond strength of autopolymerizing acrylic resin to Co-Cr. MATERIALS AND METHODS. Co-Cr alloy specimens were divided into five groups according to the surface conditioning methods. C: No treatment; SP: flamed with the Silano-Pen device; K: airborne particle abrasion with $Al_2O_3$; Co: airborne particle abrasion with silica-coated $Al_2O_3$; KSP: flamed with the Silano-Pen device after the group K experimental protocol. Then, autopolymerized acrylic resin was applied to the treated specimen surfaces. All the groups were divided into two subgroups with the thermal cycle and water storage to determine the durability of the bond. The bond strength test was applied in an universal test machine and treated Co-Cr alloys were analyzed by scanning electron microscope (SEM). Two-way analysis of variance (ANOVA) was used to determine the significant differences among surface treatments and thermocycling. Their interactons were followed by a multiple comparison' test performed uing a post hoc Tukey HSD test (${\alpha}=.05$). RESULTS. Surface treatments significantly increased repair strengths of repair resin to Co-Cr alloy. The repair strengths of Group K, and Co significantly decreased after 6,000 cycles (P<.001). CONCLUSION. Thermocycling lead to a significant decrease in shear bond strength for air abrasion with silica-coated aluminum oxide particles. On the contrary, flaming with Silano-Pen did not cause a significant reduction in adhesion after thermocycling.

• 한국재료학회지
• /
• 제17권11호
• /
• pp.587-592
• /
• 2007

Al-42wt%Nb powder was prepared by high-energy mechanical milling(HEMM). The particle size, phase transformation and microstructure of the as-milled powder were investigated by particle size distribution (PSD) analyzer, scanning electron microscopy (SEM), X-ray diffractometery (XRD), transmission electron microscopy (TEM)and differential thermal analysis (DTA). The milled powders were heated to a sintering temperature at 1000C with under vaccum with vaccum tube furnace. Microstructural examination of sintered Ti-42wt%Nb alloy using 4h-milled powder showed Ti-rich phases (${\alpha}$-Ti) which are fine and homogeneously distributed in the matrix (Nb-rich phase: ${\beta}$-Ti). The sintered Ti-42wt%Nb alloy with milled powder showed higher hardness. The microstructure of the as quenched specimens fabricated by sintering using mixed and milled powder almost are same, but the hardness of as quenched specimen fabricated by using mixed powder increased due to solution hardening of Nb in Ti matrix. The aging effect of these specimens on microstructural change and hardening is not prominent.

• 대한방사성의약품학회지
• /
• 제1권1호
• /
• pp.23-30
• /
• 2015

Radioisotopes emitting low-range highly ionizing radiation such as ${\beta}$-particles are of increasing significance in internal radiotherapy. Among the ${\beta}$-particle emitting radioisotopes, $^{67}Cu$ is an attractive radioisotope for various nuclear medicine applications due to its medium energy ${\beta}$-particle, gamma emissions, and 61.83-hour half-life, which can also be used with $^{64}Cu$ for PET imaging. The production and application of the ${\beta}$-emitting radioisotope $^{67}Cu$ for therapeutic radiopharmaceutical are outlined, and different production routes are discussed. A survey of copper chelators used for antibody labeling is provided. It has been produced via proton, alpha, neutron, and gamma irradiations followed by solvent extraction, ion exchange, electrodeposition. Clinical studies using $^{67}Cu$-labelled antibodies in lymphoma, colon carcinoma and bladder cancer patients are reviewed. Widespread use of this isotope for clinical studies and preliminary treatments has been limited by unreliable supplies, cost, and difficulty in obtaining therapeutic quantities.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 추계학술대회 논문집 Vol.16
• /
• pp.136-139
• /
• 2003

Copper has attractive properties as a multi-level interconnection material due to lower resistivity and higher electromigration resistance as compared with Alumina and its alloy with Copper(0.5%). Among a variety of agents in Copper CMP slurry, $H_2O_2$ has commonly been used as the oxidizer However. $H_2O_2$ is so unstable that it requires stabilization to use as oxidizer Hence, stabilization of $H_2O_2$ is a vital process to get better yield in practical CMP process. In this article the stability of Hydrogen Peroxide as oxidizer of Copper CMP slurry has been investigated. When alumina abrasive was used, $\gamma$-particle Alumina C had a better stability than $\alpha$-particle abrasive. As adding KOH as pH buffering agent, $H_2O_2$ stability in slurry decreased. Urea hydrogen peroxide was used as oxidizer, an enhanced stability was gotten. When $H_3PO_4$ as $H_2O_2$ stabilizer was added, the decrease of $H_2O_2$ concentration in slurry became slower. Even though adding $H_2O_2$ in slurry after bead milling lead to better stability than in advance of bead milling, it had a lower dispersibility.