• Korean Journal of Materials Research
• /
• v.33 no.12
• /
• pp.537-549
• /
• 2023

The sintering shrinkage behaviors of low temperature cofired ceramics (LTCC) and resistors were compared using commercial LTCC and thick-film resistor pastes, and factors influencing the camber of cofired resistor/LTCC bi-layers were also investigated. The onset of sintering shrinkage of the resistor occurred earlier than that of LTCC in all resistors, but the end of sintering shrinkage of the resistor occurred earlier or later than that of LTCC depending on the composition of the resistor. The sintering shrinkage end temperature and the sintering shrinkage temperature interval of the resistor increased as the RuO₂/glass volume ratio of the resistor increased. The camber of cofired resistor/LTCC bi-layers was obtained using three different methods, all of which showed nearly identical trends. The camber of cofired resistor/LTCC bi-layers was not affected by either the difference in linear shrinkage strain after sintering between LTCC and resistors or the similarity of sintering shrinkage temperature ranges of LTCC and resistors. However, it was strongly affected by the RuO₂/glass volume ratio of the resistor. The content of Ag and Pd had no effect on the sintering shrinkage end temperature or sintering shrinkage temperature interval of the resistor, or on the camber of cofired resistor/LTCC bi-layers.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.1
• /
• pp.37-42
• /
• 2016

PURPOSE. This study investigated the effect of amount of thickness reduction on color and translucency of dental monolithic zirconia ceramics. MATERIALS AND METHODS. One-hundred sixty-five monolithic zirconia specimens ($16.3mm{\times}16.3mm{\times}2.0mm$) were divided into 5 groups (Group I to V) according to the number of A2-coloring liquid applications. Each group was then divided into 11 subgroups by reducing the thickness up to 1.0 mm in 0.1-mm increments (Subgroup 0 to 10, n=3). Colors and spectral distributions were measured according to CIELAB on a reflection spectrophotometer. All measurements were performed on five different areas of each specimen. Color difference (${\Delta}E^*{^_{ab}}$) and translucency parameter (TP) were calculated. Data were analyzed using one-way ANOVA and multiple comparison $Scheff{\acute{e}}$ test (${\alpha}=.05$). RESULTS. There were significant differences in CIE $L^*$ between Subgroup 0 and other subgroups in all groups. CIE $a^*$ increased (0.52<$R^2$<0.73), while CIE $b^*$ decreased (0.00<$R^2$<0.74) in all groups with increasing thickness reduction. Perceptible color differences (${\Delta}E^*{^_{ab}}$>3.7) were obtained between Subgroup 0 and other subgroups. TP values generally increased as the thickness reduction increased in all groups ($R^2$>0.89, P<.001). CONCLUSION. Increasing thickness reduction reduces lightness and increases a reddish, bluish appearance, and translucency of monolithic zirconia ceramics.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.86-86
• /
• 2009

The $(Na_{0.5}K_{0.5})NbO_3-SrTiO_3$ ceramics were produced by the conventional solid-state sintering method, and their microstructure and electrical properties were investigated. All $(Na_{0.5}K_{0.5})NbO_3-SrTiO_3$ ceramic show dense and homogeneous structure without the presence of the rosette structure. The dielectric constant, loss and remanent polarization of $(Na_{0.5}K_{0.5})NbO_3-SrTiO_3$ ceramics were superior to those of single composition $(Na_{0.5}K_{0.5})NbO_3$

• The Journal of the Korean dental association
• /
• v.49 no.5
• /
• pp.279-285
• /
• 2011

Currently there is no dental ceramic material can be used in all dental situations need to be restored. However, in view of recent clinical reports, the most viable alternative is zirconia ceramic. Clinical success of dental zirconia restorations strongly depends on proper selection of materials, accurate laboratory procedure and final cementation, which can be achievable with the correct understanding of zirconia. As dental materials, zirconia ceramics have a very bright future, because they are being used increasingly in the anterior region as implant fixtures, as well as crown and bridge restorations and implant abutments. Many dental ceramics showing poor clinical performance have been gone from the dental market. However, in terms of outstanding mechanical properties and esthetic nature, new dental materials can replace zirconia ceramics will not be available in the foreseeable future.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.693-696
• /
• 2003

Piezoelectric ceramics were made by a doctor blade methode and piezoelectric fans were fabricated by sandwiched a slim and long metal between two layers of ceramics. A maximum displacement of piezoelectric fan occurs in the resonance frequency of a long metal and the resonance frequency of them is in inverse proportion to the square of a length of metal. The piezoelectric fan made from a wide and thin piezoelectric ceramics($13{\times}0.2{\times}30mm^3$) showed a maximum displacement in all samples, and the maximum displacement was about 20mm in a commercial power (200V, 60Hz of sine wave).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.7
• /
• pp.597-601
• /
• 2002

In this study, the structural, dielectric and piezoelectric properties of $Pb[(Ni_{1/3}Nb_{2/3})_x-(Mn_{1/3}Nb_{2/3})_{0.09-x}-(Zn_{0.505}Ti_{0.495)_0.91]O_3$ (x=0, 0.01, 0.02, 0.03, 0.04, 0.05) system ceramics were investigated to develop the composition ceramics for piezoelectric transformer. All the specimens were sintered at $1250^{\circ}C$ and its physical properties were measured, and the results are as follows : With increasing PNN substitution for PMN-PZT system, dielectric constant was increased and electro-mechanical coupling factor($k_p$) was increased to 0.62 at 5 mol% while mechanical quality factor(Qm) was decreased.

• Journal of the Korean Ceramic Society
• /
• v.32 no.8
• /
• pp.893-900
• /
• 1995

The porous wollastonite ceramics were fabricated after firing calcium silicates, obtained using natural resources and by-products of power plants by hydrothermal synthesis, without organic fibers or asbestos for reinforcement agent. A specimen from diatomite as a SiO2 staring raw material had the highest strength owing to normal grain growth and good densification from homogeneous sperhcial C-S-H hydrates. A specimen from SiO2 sol as a SiO2 starting raw material showed tobermolite, but fly ash and mixed system did xonotlite after hydrothermal synthesis. The specimen from fly ash showed the lowest firing shirikage and strength changes in the firing range from 50$0^{\circ}C$ to 120$0^{\circ}C$. The other phases in all specimens changed to wollastonite phase after firing at 100$0^{\circ}C$. Also the average pore size was distributed from 0.2${\mu}{\textrm}{m}$ to 2${\mu}{\textrm}{m}$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.442-445
• /
• 2001

In this study, microstructural and dielectric properties of $Pb_{0.83}(La_{0.2}Ce_{0.8})_{0.08}TiO_3$(PCT) ceramics as a function of $MnO_2$ addition were investigated for 30MHz ceramic resonator application. Grain size was gradually increased according to the increase of $MnO_2$ addition amount and showed the highest value of $1.502{\mu}m$ at the 0.9wt% $MnO_2$. Moreover, density showed the highest value of $7.582 g/cm^3$ at the 0.7wt% $MnO_2$.All the composition ceramics,curie temperature was nearly constant around $330^{\circ}C$

• Journal of the Korean Ceramic Society
• /
• v.42 no.11 s.282
• /
• pp.770-776
• /
• 2005

Hardening and hydroxyapatite(HAp) formation behavior of the bioactive cements in the system of $CaO-SiO_{2}-P_{2}O_{5}$ glasses and the corresponding glass-ceramics were studied. DCPD (Dicalcium Phosphate Dihydrate: $CaHPO_4{\cdot}2H_2O$) and DCPA (Dicalcium Phosphate Anhydrous: $CaHPO_4$) were developed when the prepared glass and glass-ceramic powders were mixed with three different solutions. The DCPD and DCPA transformed to HAp when the cement was soaked in Simulated Body Fluid (SBF), and this HAp formation strongly depended on the releasing capacity of $Ca^{2+}$ ions from the cements. The glass-ceramic containing apatite showed fast setting, but no HAp formation was observed because no $Ca^{2+}$ ions were released from this glass-ceramics. The compressive strength of the cements increased with reaction time in SBF until all DCPD and DCPA transformed to HAp.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1232-1233
• /
• 2006

To co-fire with commercial LTCC (Low Temperature Co-fired Ceramic) materials at $850^{\circ}C{\sim}880^{\circ}C$, different contents of $B_2O_3$ were added to the $Bi_2O_3-ZnO-Nb_2O_5$ (BZN) ceramics. According to the test results, the cubic phase of BZN was transformed into orthorhombic in all the test materials. $BiNbO_4$ phase was formed in test materials with $2{\sim}5wt%$ of $B_2O_3$ addition. The phase transformation of cubic BZN was controlled during the synthesis process with excess ZnO content. The Cubic and orthorhombic phases of BZN could coexist and be sintered densely at $850^{\circ}C/2hr$.