• 한국산학기술학회논문지
• /
• 제21권4호
• /
• pp.324-329
• /
• 2020

비상피난 지원시스템은 화재 발생시 차연막이 형성되고 차연막 내부로 외기를 급기 가압을 해주어 연기의 유입을 막아주어 안전한 대피로를 제공한다. 본 연구에서는 수치해석을 통해 급기구 지름이 10, 15, 20, 30 mm로 변화 할 때 비상피난 지원시스템 차연막 내부에 급기구 크기가 유동에 미치는 영향을 분석하였다. 그 결과 급기구 지름이 감소할수록 비상피난지원 시스템 입구부터 출구 길이 방향으로 급기구를 통한 유량이 비교적 고르게 형성 되는 양상을 보였다. 또한 20 mm 이상으로 급기구를 타공 할 경우 출구부 근처에는 급기 유량이 거의 발생하지 않는 문제점이 발생 하므로 급기구 지름을 20 mm 보다 작게 타공 해야 할 것으로 판단된다. 차연막 내부 공간 압력은 20 mm 이하로 타공시 길이 방향으로 비교적 매우 균일한 분포를 보였다. 또한 수치해석 결과를 이용하여 급기구의 부차 손실계수을 산출 하였으며 약 K=1.5 으로 계산되었다. 따라서 향후 비상피난 지원 시스템 설계시 본 연구에서 도출한 급기구 지름에 따른 유동특성과 급기구의 부차손실을 적용하여 적절한 설계가 수행될 수 있을 것으로 판단된다.

• 한국식품저장유통학회지
• /
• 제10권4호
• /
• pp.466-469
• /
• 2003

콜드체인용 골판지 상자의 냉기공과 상자의 압축강도와의 관계를 알아보고자, 골판지 상자에 각각 냉기공을 2 또는 3개를 뚫고, 냉기공의 크기와 면적을 달리하여 상온(RH 70$\pm$5 %)에서 4주간 저장하면서 골판지 상자의 압축강도를 측정하였다. 냉기공 면적이 4, 7, 10 %모두에서 냉기공의 크기가 폭은 좁고 길이가 긴 것이 압축강도가 높게 나타났다. 또한 냉기공 면적에 따른 압축강도를 살펴보면 냉기공 면적이 4 %인 상자가 다른 상자들에 비해 압축강도가 10 %이상 높게 나타났다. 하지만 냉기공 수에 따른 상자의 압축강도는 냉기공 2개와 3개간에 10 %미만의 압축강도 차이를 보여, 골판지 상자의 압축강도를 높이기 위해서는 냉기공이 차지하는 면적을 줄이고 냉기공의 모양은 폭이 좁고 길이는 길게 하는 것이 바람직할 것으로 판단되었다.

• 반도체디스플레이기술학회지
• /
• 제6권1호
• /
• pp.59-64
• /
• 2007

Non-contact transportation of a large-sized glass plate using air cushion for the vertical sputtering system of liquid crystal display (LCD) panel was considered. The objective of the study was to design an air pad unit which was composed of multiple injection and exhaust holes and mass flow supplying pipe. The gas was injected through multiple small holes to maintain the force for levitating glass plate. After hitting the plate, the air was vented through exhaust holes. Complex flow field and resulting pressure distribution on the glass surface were numerically studied to design the air injection pad. The exhaust hole size was varied to obtain evenly distributed pressure distribution at fixed diameter of the injection hole. Considering the force for levitating glass plate, the diameter of the exhaust hole of 30 to 40 times of the gas injection hole was recommended.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1555-1558
• /
• 2005

In this study, we measured cylindricity and Runout of the air bearing spindle, and tested PCB(printed circuit boards) drilling with 0.4mm micro drill at 90,000rpm and 110,000rpm in order to obtain drilling hole error. Results are as follows; The air bearing spindle's Runout was not so high within $10\mu{m}$ from 20,000rpm to 80,000rpm but it grew after 80,000rpm. Drilling hole size error was 9% at 80,000rpm and 12% at 110,000rpm because of spindle's Run out. Drilled hole shape falsified more 110,000rpm than 90,000rpm.

• 한국군사과학기술학회지
• /
• 제11권2호
• /
• pp.144-151
• /
• 2008

An experimental study has been conducted to investigate the effects of circular damage hole on the characteristics of airfoil performance. The damage on a wing created from a hit by anti-air artillery was modeled as a circular hole. Force balance measurements and static pressure measurements on the wing surface were carried out for the cases of having damage holes of 10% chord size at quarter chord and/or half chord positions. All experiments were conducted at Reynolds number of $2.85\times10^5$ based on the chord length. The surface pressure data show big pressure alterations near the circular damage holes. This abnormal surface pressure distribution produces shear stress that could lead to the acceleration of the structural degradation of the wing around the circular damage hole. However, in spite of the existence of circular damage holes, the measured force data indicated the only a slight decrease in lift accompanied by increase in drag compared to the results of undamaged one. The influence of damage hole on the aerodynamic performance was increased as the location of damage moved to the leading edge. The effect on the control force was insignificant when the damaged size was not large.

• 한국가시화정보학회지
• /
• 제9권3호
• /
• pp.38-43
• /
• 2011

When draining takes place through an axially located drain port in a cylindrical tank without any prevent, a vortex with an air core occurs. In this study, semi spherical concave and convex meshes with different size inner hole are used to find the air core can suppress. The study is carried out with different values of inner hole of mesh and different install direction of semi spherical mesh using PIV and measured velocity distribution. By providing a mesh, the air core can be prevented, even if the ratio of inner hole of mesh and diameter of cylinder is around 0.66. The experimental results show that a convex mesh type is more effective to suppress the air core generation than a concave mesh type.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.112-120
• /
• 2005

The injector, which is used in a 4-valve gasoline engine, is required to be maintained the dual stream because of the design of dual intake port. In addition, the spray characteristics of fuel injector have strong influence on engine performance, exhaust emission, fuel consumption, and especially the cold start condition for the port injection. So, commercial gasoline injectors off different type were inspected. Those are 2 hole,4 hole, air shroud 4 hole, and air shroud 4 hole injector with separator. The spray behavior of dual stream was researched by the visualization system and PDPA system was employed to measure the droplet size. Atomization is one of the most important characteristic, so droplet size distributions and SMD are investigated. And the spray characteristics of each injector are also analyzed such as the spray tip penetration, spray angle, and separation angle.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2006년도 추계학술대회 발표 논문집
• /
• pp.138-144
• /
• 2006

Non-contact transportation of a large-sized glass plate using air cushion for the sputtering system of liquid crystal display panel was considered. The gas is injected through multiple small holes to maintain the force for levitating glass plate. Complex flow field and resulting pressure distribution on the glass surface was numerically studied to design the air injection pad. The exhaust hole size was varied to obtain evenly distributed pressure distribution at fixed diameter of the injection hole. Considering the force for levitating glass plate, the diameter of the exhaust hole of 30 to 40 times of the gas injection hole was recommended.

• Journal of Biosystems Engineering
• /
• 제20권4호
• /
• pp.351-359
• /
• 1995

In pressure cooling system, produce were packed in vented box and cooled rapidly by producing a difference in air pressure on opposite faces of stacks of vented box. So, energy requirements and performance of pressure cooling system depended upon the air flow rate and the static pressure drop through packed produce in vented box. The static pressure drop across packed produce in vented box normally depended upon air flow rate, vent area of box and conditions of produce bed (depth, porosity, stacking patterns, size and shape of products) in box. The objectives of this study were to investigate the effect of vent area and air flow rate on airflow resistance of empty box and packed produce in vented box, and to investigate the relationship between the air flow resistance of packed products in vented box and sum of air flow resistance of empty box only and products in bulk only. Mandarins and tomatoes were used in the experiment. The airflow rate were in the range of 0.02~1.0$m^3$/s.$m^2$, the opening ratio of vent hole were in the range of 2.5~20% of the side area. The results were summerized as follows. 1. The pressure drops across vented box increased in proportion to superficial air velocity and decreased in proportion to opening ratio of vent hole. A regression equation to calculate airflow resistance of vented box was derived as a function of superficial air velocity and opening ratio of vent hole. 2. The pressure drops across packed produce in vented box increased in proportion to superficial air velocity and decreased in proportion to opening ratio of vent hole. 3. Because of the air velocity increase in the vicinity of vent hole in box, the airflow resistances of packed products in vented box were always higher than sum of air flow resistance of empty box only and products in bulk only. 4. Based on the airflow resistance of empty box and products in bulk, a regression equation to calculate airflow resistance of packed products in vented box was derived.

• 한국주거학회:학술대회논문집
• /
• 한국주거학회 2002년도 추계학술발표대회
• /
• pp.321-326
• /
• 2002

To design mechanical ventilation for bathroom of apartment houses where air supply and exhaust are taken Into consideration, mock-ups of ventilation systems, widely used in bathroom of apartment houses with an area of 100$m^2$, were made and installed in a laboratory, These ventilation mock-ups were available for control of air supply and exhaust, and the size of supply openings were 40cm$\times$1cm, 40cm$\times$3cm, 40cm$\times$5cm. They were installed at five positions, spaced 40cm at a height of 25cm from the floor. and the position of exhaust fans were four corners and center Exhaust fan established each one on corner of the ceiling and one in center. As result that measure ventilation effect by each condition, size of hole that supply air is big, and ventilation effect took effect to be good establishment location is low, Also, distance of exhaust fan is far with hole that supply air, ventilation effect took effect by superior thing.