• 한국도로학회논문집
• /
• 제17권3호
• /
• pp.27-33
• /
• 2015

PURPOSES : To ensure appropriate RCC properties with sufficient strength development and workability, it is necessary to secure a proper level of consistency. It is also necessary to secure maximum dry density, which is an important factor for increasing the interaction of aggregate interlocking, leading to an augmentation of RCC strength. On the other hand, the dry density of RCC can be changed owing to the compaction conditions, water content, and particle size distribution. A Proctor test and a modified Proctor test were used for determining the optimum water content needed to achieve maximum dry density with different amounts of compaction energy. A Vebe test, on the other hand, was used for checking the level of consistency, which is important for producing a workable mixture. METHODS : To confirm the degree of compaction at various particle sizes, RCC mixtures with different sand/aggregate ratios were evaluated. The Proctor test and modified Proctor test were applied to these mixtures to check the effect of the aggregate gradation and compaction energy on the maximum dry density and optimum water content. During each test, three specimens were produced for all types of water content under each aggregate gradation. A compaction curve and the optimum water content and maximum dry density for each aggregate gradation were then obtained for both tests. The range of water content for the appropriate consistency of each aggregate gradation was determined through a Vebe test. The optimum water content was then evaluated based on this range. RESULTS : The compaction test results show that the modified Proctor test provides a higher maximum dry density and lower optimum water content compared with the standard Proctor test. For the modified Proctor test, two cases of aggregate gradation (s/a = 30% and 70%) had the optimum water contents outside of the appropriate water content range. For the standard Proctor test, on the other hand, none of aggregate gradations provided the optimum water content within the desired range. CONCLUSIONS : The modified Proctor test should be used for an RCC mixture design because it can provide adequacy between maximum dry density and consistency. Moreover, the compaction roller has become highly developed for higher compaction energy.

• 한국건설순환자원학회논문집
• /
• 제7권4호
• /
• pp.71-78
• /
• 2012

순환골재는 건설폐기물을 재활용함으로써 자원절약 및 대체자원의 개발과 환경보호의 측면에서 국가 사회적으로 많은 이점을 가지고 있다. 하지만 낮은 밀도와 높은 흡수율을 가지는 저품질 순환골재는 구조용 콘크리트 골재로 사용되지 못하고 주로 저부가가치로 사용되고 있다. 따라서, 이를 위하여 폐콘크리트 파 분쇄 후 발생되는 순환골재의 재료적 특성을 규명하기 위하여 물리적인 주요성질인 시멘트함유량, 절대건조밀도, 흡수율, 등을 검토하고, 2차 제품 생산을 위한 배합설계(안)을 도출하여 이를 적용한 배합으로 생산된 시제품의 휨 강도, 흡수율, 동결 융해 후 휨 강도, 압축강도, 기건비중 등에 대한 성능평가를 실시하여 품질기준 GR규격과 비교 검토 하였다. 실헌결과 순환골재 대체율 50~90%로 증가함에 따라 GR F 4007의 성능기준 보다 우수한 품질로 나타났으며, 순환골재를 사용한 콘크리트 2차 제품의 제조 및 활용할 수 있는 소정의 물리적 특성을 확보함에 따라 각종 건설공사에서 다양하게 사용이 가능 할 것으로 판단된다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.723-726
• /
• 2004

Porous polymer concrete can be applied to roads, sidewalks, river embankment, drain pipes, conduits, retaining walls, yards, parking lots, plazas, interlocking blocks, etc. This study is to examine a content ratio of polypropylene fiber to improve bending strength, impact resistance and freezing and thawing rssistance of porous polymer concrete. Also, this study is performed to develop the porous polymer concrete using recycled coarse aggregate and blast furnace slag for application of structures needed permeability. At 7 days of curing, compressive strength, flexural strength, water permeability and flexural load are in the ragge of $17\~21MPa,\;5\~7MPa,\;4.1\times10^{-2}\~7.7\times10^{-2}cm/s$, respectively. It is concluded that the recycled aggregate can be used in the porous polymer concretes.

• 콘크리트학회지
• /
• 제2권3호
• /
• pp.81-88
• /
• 1990

본 논문에서는 방사선 자미용 중량콘크리트에 사용되는 국외의 자철광골재 콘크리트에 대하여 자철광 골재의 골재특성을 분석하고, 굳지않은 콘크리트의 슬럼프등 특성과 압축강도등 역학적특성을 분석하므로써 중량콘크리트 시공 응용에 한 참고자료를 제시하고자 하였다. 실험결과 자철광 골재 콘크리트의 슬럼프치는 천연골재의 경우보다 50% 정도 작게 단위용적중량은 50%정도 크게 나타났고, 시멘트 종류에 따른 압축강도 영향은 보통보다 중용열 포틀랜드시멘트에서 제조회사 차이로 5~19% 크게 나타났고, 잔골재의 영향은 압축강도 340kg/$cm^2$를 기준으로 그 이상 강도에서는 천연 잔골재, 그 이상 강도에서는 자철광 잔골재 콘크리트에서 크게 나타났으며, 굵은골재는 골재간결합력(Interlocking) 및 시멘트 페이스트와의 부착력(Bond) 증진에 기원하며 자철광에서 17~22%크게 나타났다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제6권4호
• /
• pp.233-242
• /
• 2002

This study is to investigate experimentally the shear capacity of high-strength lightweight-aggregate reinforced concrete beams subjected to monotonic loading. Ten beams made of fly-ash artificial lightweight high-strength concrete were tested to determine their diagonal cracking and ultimate shear capacities. The variables in the test program were longitudinal reinforcement ratio; which variabled (between 0.83 and 1.66 percent), shear span-to-depth ratio (a/d=1.5, 2.5 and 3.5), and web reinforcement(0, 0.137, 0.275 and 0.554 percent). Six of the test beams had no web reinforcement and the other six had web reinforcement along the entire length of the beam. Most of beams failed brittly by distinct diagonal shear crack, and have reserved shear strength due to the lack of additional resisting effect by aggregate interlocking action after diagonal cracking. Test results indicate that the ACI Building Code predictions of Eq. (11-3) and (11-5) for lightweight concretes are unconservative for beams with tensile steel ratio of 1.66, a/d ratios greater than 2.5 without web reinforcement. Through a more rational approach to compute the contribution of concrete to the shear capacity, a postcracking shear strength in concrete is observed.

• KCI Concrete Journal
• /
• 제12권2호
• /
• pp.23-30
• /
• 2000

This paper presents behavior of concrete pavement at transverse joint subject to static test load. The test was conducted on 1/10 scale model in the laboratory. Load transfer across the crack is developed either by the interlocking action of the aggregate particles at the faces of the joint or by a combination of aggregate interlock and mechanical devices such as dowel bars. In this study, significant three variables considered to the performance of joints were selected. : (a)diameter of dowel bars(2.5mm, 3.0mm, 4.0mm), (b)presence or absence of dowel bars, (c)aggregate types(crushed stone, round stone). Experimental results were analyzed to find relationships among displacement of discontinuous plane at jointed slab, load transfer efficiency and joint opening, etc. Displacement of discontinuous plane at joint was decreased according to the increase of dowel bar diameter. In addition, it is found that model slabs made using crushed stone had better load transfer characteristics by aggregate interlock than model slabs made using similarly graded round stone. Displacement of discontinuous plane was increased according to the increase of loading. In addition, it was decreased as dowel diameter(2.5mm, 3.0mm, 4.0mm) was increased. In the case of slab without dowel bars, displacement of discontinuous plane was greatly increased and load transfer effciency of slab applied crushed stone was shown 30 percent greater than round stone. In addition, load transfer efficiency of slabs, which were made using crushed and round stone without dowel bars, was decreased to 20 percent and 30 percent, respectively as it was compared with slabs made us-ing dowel bars.

• 대한토목학회논문집
• /
• 제35권6호
• /
• pp.1367-1375
• /
• 2015

제강슬래그 골재를 사용한 박층 아스팔트 포장공법을 위해 10 mm 밀입도 아스팔트 혼합물의 골재 입도기준을 제시하고자 하였다. 기존 WC-1, WC-3과 같은 밀입도 아스팔트 혼합물의 골재 입도기준은 퓰러모델에 의해 제시되었으나 10 mm 밀입도 아스팔트의 경우 최대밀도선과 유사한 입도를 얻게 되어 부드러운 혼합물이 되는 경향을 나타내었다. 국외 입도기준을 참고하여 골재 맞물림과 최소 골재간극률을 확보하기 유리한 입도를 제시하였다. 제시된 입도의 검증을 위해 골재 입도특성지표인 입도비(GR)와 골재다짐밀도(CAD)를 사용하여 혼합물 물성과의 상관관계를 분석하였다. 골재 입도 및 다양한 특성을 반영할 수 있는 CAD 지표의 $R^2$가 0.86~0.99로 매우 높게 나타났다. CAD 지표를 이용하여 다양한 골재 입도를 검토한 결과 제시 입도기준이 마샬안정도와 VMA 등 배합설계 인자에 보다 안정적인 것으로 나타났다. 또한 균열저항성 향상을 위해 0.3 mm 이하 골재의 통과중량백분율을 10% 이상으로 제한함으로서 터프니스가 약 15% 향상되어 효과적임을 확인 할 수 있었다.

• 한국도로학회논문집
• /
• 제17권3호
• /
• pp.49-58
• /
• 2015

PURPOSES : The use of environmentally friendly construction methods has been recently encouraged to reduce fuel consumption and the effects of global warming. For this purpose, the roller compacted concrete pavement (RCCP) construction method has been developed. RCCP is more environmentally friendly and economically efficient than general concrete by reducing the amount of CO2 generated through the application of a smaller amount of cement. RCCP has a number of advantages such as an easy construction method, low cost, high structural hydration performance, and aggregate interlocking. However, mix design standards and construction guidelines of RCCP are required for domestic application. In addition, a study on aggregate selection, which has an effect on the characteristics of RCCP, is necessary owing to a limited number of researches. Thus, the aggregate effect on the performance of RCCP in securing the required strength and workability was evaluated in consideration of domestic construction. METHODS : Sand and coarse aggregates of both 19mm and 13mm in maximum size were used in this study. Four types of aggregate gradations (s/a = 30%, 58%, and 70% for the sand and coarse aggregate of 19mm in maximum size, and s/a = 50% for a combination of the three types of aggregates) were set up to investigate the effects of the PCA band on the RCC characteristics. The conditions of s/a = 30% and 70% were evaluated to check the gradation effect outside of the recommended band. The conditions of s/a = 58% and 50% were used because they are the optimum combination of the two and three types of aggregates, respectively. RCCP gradation band was suggested gradation with a proper construction method of RCCP by synthetically comparing and analyzing the correlation of optimum water content, maximum dry density, and strength of requirements through its consistency and compaction test. RESULTS : The lower and upper limit lines are insufficient to secure a relatively strong development and workability compared to an aggregate gradation in the RCCP gradation band region. On the other hand, the line in the RCCP gradation band and the 0.45 power curve in the RCCP gradation band region were satisfactory, ensuring the required strength and workability. CONCLUSIONS : The suitable aggregate gradation on RCCP process should meet the RCCP gradation band area; however, fine particles passing through a #60 sieve do not need to be within the recommended gradation band because the influence of this region on such fine particles is small.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1998년도 가을 학술발표논문집(II)
• /
• pp.356-361
• /
• 1998

Permeable polymer cement concrete in this study is one of the invironment conscious concretes that can be applied at roads, side walks, parking lots, interlocking block and river embankment, etc. In this study, permeable polymer cement concretes using polymer dispersion(St/Ac) with water-cement ratios of 25, 30, 35 and 40%, polymer-cement ratios of 0, 5, 10, 15 and 20%, and a ratio of cement to aggregate (by weight), 1 : 3.5(about 415kg/㎥), 1 : 4.0(about 375 kg/㎥), and 1 : 4.5(about 345kg/㎥) are prepared, and tested for compressive, flexural and tensile strength, and permeability. From the test results, increase in the strengths of permeable polymer cement concrete are clearly observed with increasing polymer-cement ratio, we can obtain the maximum strengths at water-cement ratio of 35%. The optimum permeable polymer cement concrete according to application and location of work can be selected in various mix proportions.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1990년도 가을 학술발표회 논문집
• /
• pp.1-6
• /
• 1990

Joints are provided in cement concrete pavements to control transverse and longitudinal cracking that occur due to restrained deformations caused by moisture and temperature variations in the slab. But the construction of joints reduces the load-carrying capacity of the pavement at the joints, and pavements have beem deteriorated by cracks at the slab edges along the joints due to traffic loads. Therefore, it is important to analyze the behavior of joints accurately in the design of cement concrete pavements. In this study, the mechanical behavior of cement concrete pavement slabs is analyzed by the plate-finite element model, and Winkler foundation model is adopted to analyze the subgrades. The load transfer mechanism of joints are composed of dowel action, aggregate interlocking, and tied-key action, and the analytical program is developed using these joint models.