• 대한기계학회논문집A
• /
• 제24권2호
• /
• pp.431-437
• /
• 2000

In this paper, thermite and gas pressure weldings have been used to join rails in-track and analyzed as functions of hardness and wear characteristics. The wear rate of thermite welded rail is low compared with that of gas pressure welded rail, which is tested in a pin-on-disk wear tester. The hardness of thermite welded materials is relatively high and narrowly distributed between three zones; welded part, thermally affected zone, and base matrix. Wear of a welded rail may be a major factor in railroad maintenance costs and failures at the rail-rail huh joint.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.148-153
• /
• 2004

This paper represents that parts of a large generator operating in 1000 MW are affected by centrifugal forces due to high-speed rotation in 3600 rpm and 3D FEM Analyses are required to obtained the structural reliability of the generator. From these results, one would know the weakest locations and the stress distributions. The fatigue life is calculated in order to grasp the remaining life of generator. 2D and 3D analyses are performed to calculate stresses of the generator rotor and the retaining ring. From 2D results, we find the SCF at the slot and sub-slot of the rotor. 3D analysis is applied at the end part of generator rotor, which represents complex geometry, and rotor and retaining ring shrink thermally. With these results, designers of rotor and retaining ring can compare with the results of design code and verify the stress distributions of generator rotor and retaining ring, and then calculate the remaining life from the low-cycle fatigue data.

• 환경영향평가
• /
• 제14권6호
• /
• pp.415-425
• /
• 2005

To examine the geochemical behavior and pollution of soils in Gwangju City, an analysis was carried out for pH, on the contents of metals, and organic carbon. Soil samples were taken from environs areas, industrial areas and downtown areas. The major factor controlling the behavior of metallic elements in the soil was chemical weathering of clay mineral in the environs areas, industrialization, and urbanization. Heavy metals including Cu, Pb and Zn were highly enriched for the samples from central part of downtown area. This indicated that the urbanization and the industrialization affected soil pollution. The results show that soil pollution in a metropolitan city which is caused by harmful heavy metals is severest in the center of the city. In consequence, it is inevitable that practical measures should be taken to prevent soil pollution expansion.

• Applied Microscopy
• /
• 제28권3호
• /
• pp.391-398
• /
• 1998

The morphological phenotype on ocellus of Drosophila rdgC mutant was observed with electron microscope. The result showed the particular phenotype that was not found in other retinal degenarative mutants. The most distinct difference was the orientation of photoreceptor cells. The photoreceptor cells did not attached to corneagenous cells but dropped under corneagenous cells and assembled around newly formed space. Enormous multivesicle bodies caused by the degeneration of photoreceptor cells were frequently found. Rhabdomeres were also severely degenerated in consequence of the mutant. Another degeneration was found in a part of photoreceptor cell, but the degeneration of subrhabdomeric cisternae (SRC) was not found. It was a ovious difference of rdgC comparing with other two retinal degenerative mutants, rdgA and rdgB. As a result, rdgC mutant was affected on the attachment between photoreceptor cells and corneageneous cells, and it suggested the defect of cell-cell attachment. In addition, rdgC mutant was accompanied by the defect not only in retina but nerve system. The results were agreed to the reference discussion that the rdgC molecule is exist in the nerve.

• 한국의류학회지
• /
• 제27권2호
• /
• pp.169-176
• /
• 2003

This empirical research aimed to identify and compare key success factors in fashion marketing education in Korea as well as those in U.S.A. Employing a couple of statistical methods (multiple regression and factor analysis) on survey data, it was found that the decisive factors in the fashion marketing education differed between two countries. mainly attributable to the difference of goals in the education or to the job orientation of students. Surprisingly it was also found that no educational methods significantly affected the educational performance in both countries, implying that the so called constructivistic ways of leaching/learning was not so effective as expected. In order to improve educational performance in Korea, as far as fashion marketing is concerned, universities needed to increase the class-hours for the course, to provide more supportive educational environment, and to let the instructors used computer/internet facilities for more diverse purposes than now.

• 한국의류학회지
• /
• 제25권4호
• /
• pp.665-672
• /
• 2001

Fibrillation is caused by wet abrasion and occurs during scouring treatments, domestic laundering and wet finishing. So, for clean fabrics, fibrillation must either be prevented or removed after it has occurred. In this study, we researched the influence thickness of tencel on fibrillation occurrence. And the three methods of SEM photograph, reflectance values and gray level values were used in order to present proper evaluation method for fibrillation. The results are as follows. The thickness of tencel was high affected with occurrence of fibrillation, that is, as the thickness of fabrics thicker, the fibrillation occurer. And all method applicated as fibrillation evaluation method very effected without big difference, but they come into be a little question in the side of exactness.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.258-263
• /
• 2005

The nearest variety of the industrial world requires using the high precision and resolution positioning technology to do a semi-conductor, information field , and measurement field. It is especially important for the positioning technology that makes up a proper controller, is affected by the minimal heat and vibration, and can control a structurally generated non-linear friction factor to determine the efficiency of the system. The paper is to analyze the vibration characteristic according to the speed of linear motor and grasp the dynamic characteristic through the modal test and show the verification of the experimental result and design parameters by using FEM(Finite Element Method). Also, it shows the optimum standard analyzed the acceleration patterns of the moving part that lead to the vibration source in linear motor. It presents the analyzed dynamic of linear motor in compliance with a change of the non-linear factor.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 추계학술대회논문집
• /
• pp.596-599
• /
• 2008

Traditionally, tire made a role of function, which is supporting vehicle load, making brake, transferring traction, etc. But tire is a part of vehicle design, nowadays. In accordance with this market trend, customers need a wide tread design tire (i.e. low series tire). Generally low Series Tire means stiffer than general tire. That brings out increasing road noise. (Especially tire cavity resonance noise) Tire noise is divided in structure home noise and air borne noise. Tire cavity resonance noise (structure home noise) come from vibration between tire and vehicle. In the study, we investigated that tire cavity resonance noise is affected by stiffness of tread and sidewall.

• 소성∙가공
• /
• 제24권4호
• /
• pp.248-255
• /
• 2015

The warm drawing of magnesium alloy AZ31B sheet is affected by temperature because tensile elongation is changed due to the elevated temperature. In the current study, the effect of temperature was investigated for an automotive dash panel part by both experimental and FE analysis. Tensile tests were performed to obtain mechanical properties for various temperatures. AZ31B alloy sheet shows increased total elongation with increasing deformation temperature in the range of 200 to 300℃. The heating channel inserted into the die was used to regulate and to obtain an optimal temperature. A temperature controller was constructed to reduce temperature variation. Warm drawing of magnesium alloy AZ31B was performed to produce the desired shape of the lightweight automotive dash panel. The simulated results showed good agreement with the experimental results.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.1402-1403
• /
• 2011

Photovoltaic solar energy policy in the keynote of the world in the development of new technologies in terms of renewable energy sources has been a great interest. Solar energy is the energy density, low light intensity, temperature, and a lot of areas affected by the difference, the effective use difficult. For the installation of photovoltaic solar power systems to develop farmland or forest land resulting from deforestation has become such a problem. In this paper, a way to resolve these issues as part of the development of the reservoir water through the efficient use of land and water resources through the eco-friendly energy production, water quality improvement, the cooling effect of solar modules, solar water system has the advantage of was installed. Terrestrial solar systems installed under the same conditions and solar radiation, power, module temperature, ambient temperature and analyzed. Through this award to demonstrate the effectiveness of the solar system is.