• Bulletin of the Korean Chemical Society
• /
• v.30 no.6
• /
• pp.1349-1352
• /
• 2009

We report the results of the surface chemistry of deuterized ethanol exposed Zircaloy-4 (Zry-4) surfaces with various amount of $C_2D_5$OD exposures at 190 K. This system was examined with Auger electron spectroscopy (AES) and temperature programmed desorption (TPD) techniques. In TPD study, $D_2$ was evolved at two different desorption temperature regions accompanying with broad desorption background. The lower temperature feature at around 520 K showed first-order desorption kinetics. The high temperature desorption peak at around 650 K shifted to lower desorption temperature as the exposure of $C_2D_5$OD increased. The Zr(MNV) Auger peak shifted about 2.5 eV from 147 eV to lower electron energy followed by 300 L of $C_2D_5$OD dosing. This implies metallic zirconium was oxidized by deuterized ethanol adsorption. After stepwise annealing of the oxidized Zry-4 sample up to 843 K, the shifted Zr(MNV) peak was gradually shifted back to metallic zirconium peak position. After the sample was heated to 843 K, the oxygen content near the Zry-4 surface was recovered to clean surface level. The concentration of carbon, however, was not recovered by annealing the sample.

• Journal of environmental and Sanitary engineering
• /
• v.18 no.3 s.49
• /
• pp.43-47
• /
• 2003

The desorption characteristics of NaY zeolite, of which Si/Al ratio is 2.36, was measured at 25${\circ}$C and 150${\circ}$C so as to be used practically as a adsorbent for separation of sulfur oxides from flue gas, for which adsorption and desorption cycles at 25${\circ}$C were repeated four times and that at 150${\circ}$C was done one time. As a result it took 30.8 at 150${\circ}$C and 164.1 minutes in average at 25${\circ}$C to reach equilibrium condition. It means that regeneration of the NaY zeolite can be done below 150${\circ}$C so that zeolite can be used for flue gas desulfurization.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1996.06c
• /
• pp.886-895
• /
• 1996

To fit the desorption isotherm and adsorption isotherm for Pangola grass, the modified Henderson model, Chung-Pfost model, modified Halsey model, and modified Oswin model were used to fit the experimental EMC /ERH data. A step-by -step ERH measuring technique was used in this study. The ERH data were collected at three temperature levels of 5 $^{\circ}C$, $25^{\circ}C$ and 5$0^{\circ}C$ for Pangola grass whole plant, stem , and foliage. The modified Halsey model has the best fit for both desorption isotherm and adsorption isotherm of Pangola grass whole plant as compared with other models.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.360-360
• /
• 2010

Very initial stage of oxidation process of Si (001) surface was investigated using large scale molecular dynamics simulation. Reactive force field potential was used for the simulation owing to its ability to handle charge variation associated with the oxidation reaction. To know the detail mechanism of both adsorption and desorption of water molecule (for simulating wet oxidation), oxygen molecule (for dry oxidation) and their atom constituents, interaction of one molecule with Si surface was carefully observed. The simulation is then continued with many water and oxygen molecules to understand the kinetics of oxide growth. The results show that possibilities of desorption and adsorption depend strongly on initial atomic configuration as well as temperature. We observed a tendency that H atoms come relatively into deeper surface or otherwise quickly desorbed away from the silicon surface. On the other hand, most oxygen atoms are bonded with first layer of silicon surface. We also noticed that charge transfer is only occur in nearest neighbor regime which has been pointed out by DFT calculation. Atomic structure of the interface between the oxide and Si substrate was characterized in atomic scale.

• Proceedings of the KIEE Conference
• /
• 2008.05a
• /
• pp.161-163
• /
• 2008

$TiO_2-V_2O_5$ sol was fabricated using sol-gel method and $TiO_2-V_2O_5$, thin films were fabricated using dip-coating method. $V_2O_5$ sol was added 0.01mole, 0.03mole, 0.05mole into $TiO_2$ sol. Capacitance of thin films decreased with increasing $V_2O_5$ additive and it increased largest at 0.01mole. Because adsorption time and desorption time of thin films was about 2 minutes 40 seconds and about 3 minutes 40 seconds respectively, adsorption time was faster about 1 minutes than desorption time.

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1168-1177
• /
• 2000

Hydrocarbon adsorber is considered as a promising technology to reduce cold start HCs in automotive exhaust gas. In this study, three in-line adsorber systems were tried to reduce the cold start emission. To check the basic characteristics of adsorber converters, surface areas, TPD and TP A were examined after a hydrothermal aging. Also idle engine bench was used to find the adsorption and desorption capabilities of the adsorber systems at cold start. Finally a practicability of the adsorber systems for the LEV achievement was checked with FTP test on a 2.0 D MIT vehicle. The results of this study indicate that hydrocarbon adsorber system is one of the promising passive technologies to meet the ULEV regulation.

• Journal of Korean Society for Atmospheric Environment
• /
• v.17 no.1
• /
• pp.67-74
• /
• 2001

In the manufacturing process of PCB , three kinds of VOCs such as aceton, methanol and 2-metoxyethanol are being used. In this study, adsorption characteristics of activated carbon fibers(ACFs) and active carbon were examined to temove these VOCs. The experimental results showed that ACF has better adsorption and regeneration efficiency than activated carbon. Phenolic-resin based ACF showed the highest adsorption capacity and the capacity was not decreased after repeated regeneration by steam. On the adsorption and desorption experiments for ternary components, preferential adsorption with roll-over phenomena was appeared. 2-Metoxyethanol was strong adsorbaste and it displaced adsorbed methanol and aceton.

• Clean Technology
• /
• v.26 no.2
• /
• pp.137-144
• /
• 2020

Metal-impregnated activated carbons were prepared via ultrasonic-assisted impregnation method for regeneration and low ammonia concentration. Magnesium and copper were selected as metals, while chloride (Cl^-) and nitrate (NO₃^-) precursors were used to impregnate the surface of activated carbon. The physical and chemical properties of the prepared adsorbents were characterized by TGA, BET, and NH₃-TPD. The ammonia breakthrough test was carried out using a fixed bed and flowing ammonia gas (1000 mg L^-1 NH₃, balanced N₂) at 100 mL min^-1, under conditions of temperature swing adsorption (TSA) and pressure swing adsorption (PSA, 0.3, 0.5, 0.7, 0.9 Mpa). The adsorption and desorption performance of ammonia were in the order of AC-Mg(Cl) > AC-Cu(Cl) > AC-Mg(N) > AC-Cu(N) > AC through NH₃-TPD and TSA and PSA processes. AC-Mg(Cl) using MgCl₂ showed the average adsorption amount of 2.138 mmol/g at TSA process. Also, AC-Mg(Cl) showed the highest initial adsorption amount of 3.848 mmol/g at PSA 0.9 Mpa. When metal impregnated the surface of the activated carbon, it was confirmed that not only physical adsorption, but also chemical adsorption increased, making enhancement in adsorption and desorption performances possible. Also, the prepared adsorbents showed stable adsorption and desorption performances despite repeated processes, confirming their applicability in the TSA and PSA processes.

• YAKHAK HOEJI
• /
• v.36 no.6
• /
• pp.563-569
• /
• 1992

The sorption and desorption properties of four different solid adsorbents were evaluated for the trace enrichment of ibuprofen from biological samples. Chromosorb 107 gave the highest dynamic adsorption coefficient. Among the organic solvents examined, acetone gave the highest desorption coefficient. Using the Chromosorb 107 column, the optimum elution volume of the eluting solvent was evaluated from the breakthrough curve of ibuprofen. The usefulness of Chromosorb 107 as the solid adsorbent and acetone as the eluting solvent was examined for the solid-phase extraction of ibuprofen from serum in the concentration range of $20{\sim}40\;{\mu}g/ml$.

• Journal of Korean Society for Atmospheric Environment
• /
• v.14 no.2
• /
• pp.133-142
• /
• 1998

Gas adsorption on adsorbents depends on temperatures and pressures. When these parameters are fixed, the adsorption capability and selectivity can not be changed. If the gas adsorption is controlled by another factor like electromagnetic field, the adsorption and desorption can be managed by much intentional way. The microwave has characteristics to excite particular components such as water without destroying it. In this study, microwave was irradiated to the adsorbent of an NaY zeolite which is almost transparent to microwave. As vapor of 1, 1, 2- trichloro-1, 2, 2-trifluoroethane (CFC-113) and water flowed simultaneously on the zeolite packed in a column at room temperature, only water was adsorbed. The . adsorbed water was removed from the zeolite and then replaced by CFC-113, since the microwave was irradiated. Greater the power of microwave was, more CFC-113 was adsorbed. The water adsorption took place again after a latent period by stopping the microwave irradiation.