• 한국인터넷방송통신학회논문지
• /
• 제8권6호
• /
• pp.153-157
• /
• 2008

최근 산업사회에서 널리 쓰이는 전자소자들은 다층구조로 제작되고 있는 실정이며 이러한 소자의 보이지 않는 층에 대한 해석은 비파괴 검사에서 중요한 일이다. 따라서 본 논문에서는 접착층이 존재하는 다층구조물에 초음파를 입사시켰을 때 반사되는 신호를 디지털 신호처리하여 가시도를 개선하였다. 이를 위하여 다층구조물에서 반사된 신호를 전력 켑스트럼 처리하여 각층에서 나타난 첫 번째 피크와 두 번째 피크를 구할 수 있었다. 실험을 위하여 일정한 두께를 갖는 에폭시층이 존재하는 다층구조물을 형성하였고 초음파 펄스-에코 방법에 의하여 얻어진 반사신호의 가시도를 개선하기 위해 전력 켑스트럼 처리하였다.

• Structural Engineering and Mechanics
• /
• 제53권5호
• /
• pp.1017-1030
• /
• 2015

In this study, the finite element method was used to analyze the distribution of the adhesive shear stresses in the single-lap bonded joint of two plates 2024-T3 aluminum with and without defects. The effects of the adhesive properties (shear modulus, the thickness and the length of the adhesive were highlighted. The results prove that the shear stresses are located on the free edges of the adhesively bonding region, and reach maximum values near the defect, because the concentration of high stress occurs near this area.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.465-470
• /
• 2001

The adhesively-bonded joints considered in this investigation include single-lap joint and double-lap joint. For an adhesively bonded double-lap joint, end mismatch between the two cuter adherends(upper, lower) can not removed completely although it can be controlled within a manufacturing tolerance. This paper shows that the end mismatch introduces local bending and end mismatch affects the shear and peel stresses in the adhesive. The double-lap joint with an end mismatch is affected of adhesive thickness, material properties of adhesive and adherend etc. Also, we concluded that there are critical value of an end mismatch to provoke the interface fracture.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2005년도 추계학술발표대회 개요집
• /
• pp.94-96
• /
• 2005

This paper is concerned with a fracture strength study of composite adhesive lap joints. The tensile and peel tests were carried out on specimen manufactured hybrid stacked composites such as the polyester and bamboo natural fiber layer. The main objective of the work was to test the failure strength of adhesive bonded joints using hybrid stacked composites with a polyester and bamboo natural fiber layer adjacent to the fiber orientation. From results, the load directional orientation, small amount and low thickness of bamboo natural fiber layer have a good effect on the tensile and peel strength of natural fiber reinforced composites. and these characters are have a great influence on fracture strength and failure shape of adhesive bonded joints using hybrid stacked composites in the difference of fiber orientation.

• Restorative Dentistry and Endodontics
• /
• 제37권3호
• /
• pp.155-159
• /
• 2012

Objectives: To investigate the effect of dentin moisture degree and air-drying time on dentin-bond strength of two different one-step self-etching adhesive systems. Materials and Methods: Twenty-four human third molars were used for microtensile bond strength testing of G-Bond and Clearfil $S^3$ Bond. The dentin surface was either blot-dried or air-dried before applying these adhesive agents. After application of the adhesive agent, three different air drying times were evaluated: 1, 5, and 10 sec. Composite resin was build up to 4 mm thickness and light cured for 40 sec with 2 separate layers. Then the tooth was sectioned and trimmed to measure the microtensile bond strength using a universal testing machine. The measured bond strengths were analyzed with three-way ANOVA and regression analysis was done (p = 0.05). Results: All three factors, materials, dentin wetness and air drying time, showed significant effect on the microtensile bond strength. Clearfil $S^3$ Bond, dry dentin surface and 10 sec air drying time showed higher bond strength. Conclusions: Within the limitation of this experiment, air drying time after the application of the one-step self-etching adhesive agent was the most significant factor affecting the bond strength, followed by the material difference and dentin moisture before applying the adhesive agent.

• 대한기계학회논문집
• /
• 제18권4호
• /
• pp.835-845
• /
• 1994

In this paper, the effects of the adhesive thickness and adherend roughness on the static and fatigue strengths of the adhesively bonded circular single lap joints has been investigated by an experimental method. The stacking sequence effect of the composite adherend on the static and fatigue strength and the fracture patterns of the adhesive failure were also observed. Since the circular single lap joint fails catastrophically beyond the static strength of fatigue limit, the tubular polygonal adhesively bonded joints such as triangular, tetragonal, pentagonal, hexagonal as well as elliptical joints were manufactured in order to give partial mechanical characteristics to the adhesively bonded tubular joints. These joints were tested both in static and fatigue modes. From the experimental investigations, it was found that the fatigue strength of the circular adhesively bonded joints was much dependent on the arithmetical average surface roughness of the adherends and the polygonal adhesively bonded joints had better fatigue strength characteristics than the circular adhesively bonded joints.

• 산업기술연구
• /
• 제22권A호
• /
• pp.185-192
• /
• 2002

The performance of old and the new concrete construction depends upon bond strength between old and the new concrete. Current adhesive and strength measurement method ignores the effect of stress concentration from shape of specimens. Therefore, this research calculates stress concentration coefficient as the ratio of drilling depth to drilling diameter($h_s/D$), the ratio of overlay thickness to drilling diameter($h_0/D$), the ratio of steel disk thickness to drilling diameter(t/D), the ratio of overlay elastic modulus to substrate modulus($E_1/E_0$), the distance from core to corner border(L_$_{corner}$) and the distance between cores(L_$_{coic}$) vary. The finite element method is adapted to analysis The results from 'the F.E.M analysis are as follows. The stress concentration effects can be minimized when the ratio of drilling depth to drilling diameter($h_s/D$) is 0.20~0.25, the elastic modulus ratio($E_1/E_0$) is 06~1.0, and the ratio of steel disk thickness to drilling diameter(t/D) is 3.0. The overlay thickness, the distance from specimens to corner border(L_$_{corner}$), the distance between cores(L_$_{coic}$) almost do not affect to the stress concentration.

• 대한치과보철학회지
• /
• 제30권3호
• /
• pp.437-443
• /
• 1992

This study was performed to investigate the availability of adhesive resin cement for luting agent of cast crown. The resin cements used in this study were Panavia-Ex(Kuraray Co., Japan) and C & B-Metabond (Parkell Bio-Materials U.S.A.). Zinc phosphate cement was Flecks zinc cement(Mizzy Inc., U.S.A.) The film thickness of cast crown at gingival margin, lateral wall and occlusal surface was observed with measuring microscope(Modek MXT 70 Matsuzawa Seiki Co., Japan) and the retention of cast crown was measured with Instron Universal Test Machine (Instron Engineering Co., U.S.A.) The results were as follows : 1. The value of retention of cast crown was the highest in the use of Panavia-EX, followed by C & B-Metabond and 2inc phosphate cement, respectively. 2. There was no difference in film thickness among the three cements, but the film thickness in all cements was highest at occlusal surface.

• Composites Research
• /
• 제30권4호
• /
• pp.254-260
• /
• 2017

본 논문에서는 알루미늄과 복합재료에 대한 이종소재 접합면의 성형안전성을 위해 일정한 두께를 확보할 수 있는 0.1 mm, 0.2 mm, 0.3 mm bead의 적용 방법과 물성변화에 대해 연구하였고, 이를 검증하기 위해 더블랩 시험과 FEM 시뮬레이션으로 접착제의 두께에 따라 미치는 영향을 평가하였다. 그 결과, 접착제에 bead의 양을 1% 이상 함량이 증가함에 따라 접착 소재의 강도가 높아지고 신율이 감소함을 확인하였고, bead의 크기가 커질수록, 강성은 낮아지고, 신율은 증가함을 확인하였다.

• 반도체디스플레이기술학회지
• /
• 제10권1호
• /
• pp.91-94
• /
• 2011

This paper presents light transmission efficiency by optical adhesive thickness between MLA and aperture layer and by aperture hole size. The gap between MLA and Aperture layer is adjusted by the shim. The more optical adhesive thickness increases, the better light transmission efficiency increases up to a point. After that, the light transmission efficiency decreases because stray lights cannot transmit through the aperture layer owing to cut-off by aperture layer. And as a result of light transmission efficiency with changing aperture hole size, the light transmission efficiency is proportional to area of aperture hole. The more specified process is made, the better data and sample will be got.