• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.4
• /
• pp.432-438
• /
• 2008

This paper presents a new jetting dispenser driven by a piezoelectric actuator at high operating frequency to provide very small dispensing dot size of adhesive in modern semiconductor packaging processes. After describing the mechanism and operational principle of the dispenser, a mathematical model of the structured system is derived by considering behavior of each component such as piezostack and dispensing needle. In the fluid modeling, a lumped parameter method is applied to model the adhesive whose rheological property is expressed by Bingham model. The governing equations are then derived by integrating the structural model with the fluid model. Based on the proposed model, dispensing performances such as dispensing amount are investigated with respect to various input trajectories.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05b
• /
• pp.349-352
• /
• 2006

Pull-off test is generally used as a method of evaluating bond strength of FRP with concrete at the job site. However, pull-off test damages FRP composites and the maximum pull-off strength is limited up to tensile strength of concrete. Accordingly, it is required to set-up a test method that can simply evaluate bond performance of structural adhesive. This study suggested compression and bending test of epoxy resin as test methods that can indirectly evaluate performance of adhesive, as well as standardized test specification for different types of specifications from various countries. In this study, the section dimension of compression and bending test specimens is unified, and standard test specimen size is achieved by test results.

• Journal of Korea Foundry Society
• /
• v.14 no.5
• /
• pp.447-454
• /
• 1994

Wear resistance and wear mechanism of hypereutectic Al-($15{\sim}40$)wt%Si alloys were investigated. Primary Si particles under $20{\mu}m$ size were formed in hypereutectic Al-Si alloy powders due to rapid solidification. But the Si particles of extruded bars were finely distributed in smaller size than that of atomized powders. The wear mechanism of hypereutectic Al-Si alloys was divided into three types of wear phenomena, which were abrasive wear, delamination wear and severe adhesive wear according to sliding speed and load. At low sliding speed and load, wear mechanism was abrasive wear, so Al-15wt%Si alloy showed the best wear resistance. At high sliding speed and load, wear mechanism was adhesive wear, and Al-40wt%Si alloy showed the best wear resistance.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.291-293
• /
• 2012

Recently, environmental pollution and global warming and greenhouse gases are increasing, because Efforts to improve are continued throughout the world. As part of the resource recycling industry has become an important research area. In the field of waterproofing industry, focus on the resource recycling is growing, due to serious resource depletion and sharp price. Therefore, in this research on the resource recycling such as reclaimed rubber and rubber waste is enable and these eco-friendly materials are applied high adhesive flexible non-exposed type self adhesion compound waterproofing material was measured eco-friendly performance and field application was evaluated.

• Composites Research
• /
• v.25 no.1
• /
• pp.14-18
• /
• 2012

The structural adhesives have the advantage of improving automobile performances and are being applied to joining light weight materials like aluminium and composite. In order to characterize the impact behavior of structural adhesive, instrumented impact tests were performed with respect to pin-ring adhesively bonded joint specimens. Also dynamic FE analysis was carried out using LS-DYNA to compare the results with experiments.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.2
• /
• pp.124-129
• /
• 2001

The research on anticorrosive of valve for ship, waterworks, and drainage system is very important. The purpose of this paper is to develop the metal/polyurethan adhesive technique at insider of the value to prevent corrosion in the value. It is performed to the bending strength test by using metal /polyurethan in the metals (SB41, Al6061). It is investigated to the effects of bending strength on curing temperature, preheating time and curing time, and to the fracture mechanism of metal/polyurethan adhensived specimen. As a results, we find that the bending strength is the highest at curing temperature of 11$0^{\circ}C$ and the curing time is 60 minutes in metal/polyurethan adhesive specimen.

• Journal of Korean Association for Spatial Structures
• /
• v.13 no.4
• /
• pp.41-47
• /
• 2013

For the artistic column used by Glass Fiber Reinforced Plastic(GFRP), the connection of steel with GFRP were needed. Due to the fabricating characteristics of hand laminating, GFRP surfaces had to be connected. Because there were no existed data of these connection, experimental study has to be followed so that the structural strength and buckling mode could be investigated. In this paper, therefore, the axial tests of steel with GFRP were performed. The connection of GFRP's surfaces could be also tested as well. As a result, it could be figured out that the strength of these connections were determined by the adhesive strength.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.11a
• /
• pp.173-174
• /
• 2018

In this study, the objective of this study was to evaluate the adhesive characteristics of existing self-adhesive rubber asphalt sheet, butyl sheet and acrylate sheet in a low temperature environment through Tack Rolling Ball Test to obtain basic data on acrylate. As a result of this experiment, in the case of the self-molding rubber asphalt sheet and the butyl rubber sheet, the compound of the sheet was frozen in the low temperature environment and the iron bead was separated. On the other hand, the acrylate sheet did not freeze the acrylate even at 0 ℃, It is confirmed that the measured value is shown by Ball Test.

• Steel and Composite Structures
• /
• v.20 no.3
• /
• pp.671-692
• /
• 2016

FRP stay-in-place (SIP) formworks are designed as a support for casting concrete and as a tension reinforcement when concrete is cured. Bond development between SIP formwork and concrete is critical for FRP tension element to be effective. This paper reports the bond strength between FRP formwork and concrete for different interfacial treatments. A novel experimental setup is prepared for observing the bond behaviour. Three different adhesives with varying workability have been investigated. Along with the load-deformation characteristics, bond slip and strains in the formwork have been measured. A finite element numerical simulation was conducted for the experiments to understand the underlying mechanism. The results show that the adhesive bonding has the best bond strength.

• Korean Journal of Optics and Photonics
• /
• v.12 no.6
• /
• pp.460-462
• /
• 2001

We have analyzed the characteristics of IR lens mounting with elastomer and applied the results to the mounting of a silicon lens with diameter 117 mm which is the objective of a thermal imaging system. The elastomer, the 577 primerless silicone adhesive (Dow Corning Co.) which is heat cure type, and the mount material, A16061 are used for our analysis. Theoretical analysis gives the result that the space between lens and mount is required to be more than 250 ${\mu}{\textrm}{m}$ under the operational temperature conditions of -40~+6$0^{\circ}C$.