• 농업과학연구
• /
• 제44권4호
• /
• pp.487-494
• /
• 2017

Spinosad and spinetoram are widely used insecticides for the control of lepidopteran larvae, leaf miners, and thrips; however, they might also have low toxicity toward beneficial insects like bees. Because these pesticides are easily photolyzed by ultraviolet radiation, the QuEChERS method, with its simple pretreatment procedure, is often used for analyzing residues of spinosad and spinetoram. The present study performed a residue analysis using a modified QuEChERS method by pretreating with ammonium salt. The limit of detection (LOD) of the modified method was 0.05 mg/kg and the limit of quantification (LOQ) was 0.25 mg/kg. The coefficient of determination ($R^2$) for the calibration curve was 0.999. Also, we examined any change in the adhesion of spinosad and spinetoram on the plants depending on a spray volume. The adhesion was approximately 70% when the spray volume was increased from 60 L to 120 L per 10 a whereas the adhesion was approximately 37% when the spray volume was increased from 125 L to 250 L. This showed that the amount of adhesion decreased with the higher spray volume. The efficacy result of spinetoram was that over 90% of Frankliniella occidentalis was controlled with the application volume of 125 L per 10 a. Therefore, the result of this study indicates that control of insects is effective and sufficient with a spray volume of 125 L per 10 a in paprika cultivation facilities.

• 한국치위생학회지
• /
• 제20권4호
• /
• pp.535-543
• /
• 2020

Objectives: The aim of this study was to investigated the surface roughness and change in the amount of adhesion of Streptococcus mutans to the commercial pit and fissure sealant containing cerium oxide nano particles(CNPs). Methods: The CNPs was incorporated into a commercial pit and fissure sealant at 0-4.0 wt%. Disk Specimens (ϕ 10 mm × 2 mm) were prepared by light polymerization the front and back for 40s. Average surface roughness was measured and Streptococcus mutans adhesion was observed under confocal laser scanning microscopy (CLSM) after 24 hour. Data were statistically analyzed by one-way ANOVA and Tukey HSD^a post-hoc test. Results: Difference of the surface roughness(Ra) between groups was not statistically significant in both non CNPs group and CNPs group(p>0.05). In CNPs group, the amount of S. mutans adhesion was significantly different between control group and decreased in order of CNPs 4.0, CNPs 0.5, CNPs 1.0 and CNPs 2.0(p<0.05). Conclusions: Within the limitation of this study, these aspects of oral bacteria performances suggest potential usefulness of the CNPs incorporation, especially CNPs 1% and 2%, in pit and fissure sealant for inducing antibacterial effect.

• 설비공학논문집
• /
• 제13권12호
• /
• pp.1175-1183
• /
• 2001

Recently, a great attention has been paid to the ice thermal storage system for the purpose of energy saving and reduction in peak electrical demand. In the present study, it has been investigated the freezing behavior of several kinds of water solutions with nonionic surfactant. In order to prevent ice blockage in a cooled pipe, the amount and wall adhesion behavior of ice of the test fluids were observed experimentally under different concentration of water solution with surfactant, temperature of cooled wall, and the shear velocity of test fluids. The results showed that the size of ice crystal became smaller at higher shear velocity at wall. And the lowest limit of wall adhesion of ice in water solution with surfactant was found at 230 W/$m^2$ of heat flux.

• International Journal of Concrete Structures and Materials
• /
• 제2권1호
• /
• pp.3-8
• /
• 2008

Polymer-cement composites are known repair materials. The aim of this work is to investigate the influence of various amount of dispersion of carboxylated styrene-butadience copolymer on the selected mechanical properties of polymer-cement concrete (PCC) and on its adhesion to ordinary concrete. The compressive, flexural and tensile strengths as well as frost resistance and fracture resistance of the composites are tested. Adhesion strength of PCC to ordinary concrete, as one of most important performance of good repair material is evaluated and analyzed using three test methods. The results obtained in standard pull-off test are compared with the two other tests. The first one, which is an adaptation of WST (wedge splitting test) characterizes crack propagation in the plane of bond created during repair. In the second test the resistance to shear is a measure of adhesion strength.

• Journal of Korean Neurosurgical Society
• /
• 제49권6호
• /
• pp.323-328
• /
• 2011

Objective : Epidural fibrosis and adhesion are the main reasons for post-laminectomy sustained pain and functional disability. In this study, the authors investigate the effect of irradiated freeze-dried human amniotic membrane on reducing epidural adhesion after laminectomy on a rat model. Methods : A total of 20 rats were divided into two groups. The group A did not receive human amniotic membrane implantation after laminectomy and group B underwent human amniotic membrane implantation after laminectomy. Gross and microscopic findings were evaluated and compared at postoperative 1, 3 and 8 weeks. Results : The amount of scar tissue and tenacity were reduced grossly in group of rats with human amniotic membrane implantation (group B). On a microscopic evaluation, there were less inflammatory cell infiltration and fibroblast proliferation in group B. Conclusion : This experimental study shows that implantation of irradiated freeze-dried human amniotic membrane reduce epidural fibrosis and adhesion after spinal laminectomy in a rat model.

• 한국표면공학회지
• /
• 제29권2호
• /
• pp.109-119
• /
• 1996

In order to improve adhesion of electroless copper deposits on alumina substrates, some stabilizers such as 2-Mercapto Benzothiazole, thiourea and NaCN were added over a wide range of concentrations. The adhesion tests of the deposits were performed by using the cellophane tape and the push-pull scale. With the minor addition of the stabilizers, 2-MBT having a large molecular size gives poor adhesion, together with a finer grain structure, whereas Thiourea and NaCN show a high mechanical strength of the deposits. The high mechanical strength is supposed to be due to the easy desorption of hydrogen gas generated from the electroless reactions. A large amount of the three stabilizers decreases the adhesion for all the cases, resulting from strong adsorption of the stabilizers to the substrates.

• Journal of the Korean Wood Science and Technology
• /
• 제35권2호
• /
• pp.61-68
• /
• 2007

The applicable scope of adhesives in the current society is broad and currently, several types of PVAc resin are sold in the market for adhesives. PVAc resin is primarily used for wood works and paper adhesion. However, the PVAc resin itself has the disadvantages that its viscosity is highly temperature- dependent and the work condition and viscosity get worse at the low temperature in the winter seasons. Although phthalate-based plasticizer is used to complement these disadvantages, adhesion strength and heat-resistance are weakened by adding the phthalate-based plasticizer and in the winter period, the amount of quantity should be increased. Also in a high-density product, it worsens the work condition by causing a rise of viscosity and delays curing and in a low-density product, it worsens the storage stability by causing separate precipitation. In addition to these, the phthalate-based plasticizer as a material of causing environmental hormones is currently restricted in the advanced countries for its amount of use and also in the domestic market, it is necessary to prepare for the situation. This study has not only eliminated the disadvantages of PVAc resin emulsion without adding a phthalate-based plasticizer of causing these problems, but also synthesized the PVAc resin for timber adhesion that is excellent in woodwork, thermal-resistance, water-resistance, storage stability, and adhesion performance. As the result, it has proven an excellent performance in thermal resistance, water resistance, storage stability, and minimum film forming temperature.

• 접착 및 계면
• /
• 제19권4호
• /
• pp.145-153
• /
• 2018

본 연구에서는 상용성이 개선된 접착 증진제를 개발하기 위해 malenized polybutadiene과 2-hydroxyethyl acrylate(HEA)의 반응을 통해 다양한 함량의 아크릴레이트 반응기와 carboxylic acid가 도입된 접착 증진제(PBCA)를 합성하였다. 합성된 접착 증진제는 maleic anhydride의 개환 반응을 통해 도입된 아크릴레이트 반응기와 carboxylic acid의 함량, 그리고 접착 증진제의 첨가량을 달리하여 접착 필름을 제조하고 제조된 접착 필름의 표면 특성, 접착력 등의 기계적 특성과 흡습 특성 등의 변화를 확인하였다. 접착 증진제의 분자 내에 도입된 carboxylic acid의 함량이 증가할수록 접착 필름의 접착력은 증가하는 경향을 보였으며, 기존의 상용화된 접착 증진제와 비교하여 기계적 물성 또한 개선됨을 확인하였다. 특히, 분자 내에 소수성의 폴리부타디엔 주쇄와 친수성의 maleic anhydride 및 carboxylic acid가 동시에 존재함으로 인해 다양한 친수성 및 소수성 재료와의 상용성이 대폭 개선되었음을 확인하였다.

• 폴리머
• /
• 제36권2호
• /
• pp.119-123
• /
• 2012

금속 박막 접착제로 사용되는 용제형 폴리우레탄 접착제의 라미네이팅 조건에 따른 접착 메커니즘과 이에 따른 접착력 변화를 살펴보았다. 강판에 도포된 접착제의 열처리 온도와 시간에 따라 폴리우레탄 접착제의 blocking agent로 사용된 옥심이 분해되어 이소시아네이트기가 발현되고 이들이 강판과 알루미늄 포일의 하이드록실기와 반응하여 강판 접착이 이루어짐을 알 수 있었다. 접착 강도는 접착 온도 및 시간에 따라 발생된 이소시아네이트 함량과 밀접한 관계가 있음을 확인하였다. 하지만 지나친 접착 온도 및 접착 시간의 증가는 접착제에 함유된 용매의 감소와 접착제 분해를 유발시켜 접착 강도를 감소시킴을 알 수 있었다.

• Current Research on Agriculture and Life Sciences
• /
• 제32권1호
• /
• pp.18-23
• /
• 2014

본 연구에서는 유변물성측정기를 이용하여 HPMC 첨가량, 물 양, HPMC 분자량, 셀룰로오스 에테르 치환제 및 치환도가 쌀 반죽의 압축 및 집착 특성에 미치는 영향에 대해 살펴보았다. HPMC 첨가량이 증가함에 띠라 접착강도는 꾸준히 증가하였으나, 압축강도는 2% HPMC 첨가량에서 최대 강도를 보였다. HPMC의 분자량이 증가하거나, 물 양이 감소할수록 쌀 반죽의 압축강도 및 접착강도가 증가하는 결과를 보였다. 이들 인자 외에도, 셀룰로오스 에테르의 치환제 및 치환도도 쌀 반죽의 압축강도 및 접착강도를 결정하는 중요한 인자임을 확인하였다.