• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.860-865
• /
• 2000

This Paper Proposes the test pieces of X, Y and Z axes to compensate the shape distortion of Selective Laser Sintering(SLS) parts resulting from the phase change during the sintering process. In no case of the proposed compensation test pieces of X, Y axes the accurate rates of shrinkage can be measured with the reduction of curling which is obtained from adjustment of build orientation and the formula used to get scale factors are proposed with the shrinkage rates of them. The scale factors of X, Y and Z axes are generated by building up proposed compensation test pieces. The generated scale iactors are required to satisfy the dimensional accuracy even if there are changes of the build position and the size of SLS parts in the build chamber. For this reason, it is proposed that the build positions and the size be considered to be noise factors against the compensation test pieces and a method is also proposed that scale factors be selected to robustly maintain the dimensional accuracy of SLS parts under the actual operating conditions with the application of the Taguchi Method.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.12
• /
• pp.142-151
• /
• 1994

This paper proposes new algorithms to solve canonical piecewise-linear equations with linear partitions and illustrates their efficiency through the analysis of resistive network. The basic idea of the proposed algorithm is to find the best next guess, closest to the actual solution, at each Newton-Raphson (N-R) iteration by comparing the images of nest guess candidates and that of the actual solution. The proposed algorithm can reduce the number of the N-R iterations rquired for convergence greatly, compared to the actual solution, at each Newton-Raphson (N-R) iteration by comparing the images of next guess candidates and that of the actual solution. The proposed algorithm can reduce the number of the N-R iterations required for convergence greatly, compared to the Katzenelson algorithm. When applied to analyzing test circuits, the proposed algorithm required 8 to 20 times fewer N-R iterations and 5 to 10 times less CPU time than the Katzenelson algorithm, depending on the size of the circuits. The experimental results also exhibit that the efficiency of the proposed algorithm over the Katzenelson algorithm increases as the number of the piecewise-linear regions for the representation of the circuit.

• Journal of the Korean Society of Costume
• /
• v.58 no.1
• /
• pp.133-150
• /
• 2008

The purpose of this study was to recognize of the sizing system and analyze the fitting on formal pants of the on-line shopping mall for plus-sized women. To pursue this purpose, the investigation of the sizing system was focused on 22 online companies. The formal pants of 7 companies was selected among them. And actual sizes were compared with the guidance sizes of goods. For the assessment about the fitting on formal pants of 7 online companies, these came to make on to 16 obese women with 'A' body shaped and 'O' body shaped. A data analysis used the SPSS 14.0 statistics program. To verify the difference, this study used the variance analysis and Duncan's test for the postmortem verification. The result was as follows. 1. All of 22 companies were using the symbol such as 88, 99, 100 and 110 in the present condition of sizing system. The information about products size was presenting the products size not to be the body size. the guidance sizes of products were different from actual sizes of 7 companies to be assorted. Therefore, the guidance sizes of goods could not accomplish the facility. 2. According to the fitting-tests by the sensory assessment, the obese women with 'A' body shaped, did the dissatisfaction at the items of the hip circumference, abdominal region, crotch deep and pants length. The obese women with 'O' body shaped, did the dissatisfaction at the the items of crotch deep and pants length.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.332-337
• /
• 2009

The importance of the evaluation and verification of small-size cogeneration system has been emphasized because there is no KS-code related to the small-size cogeneration system. The evaluation method of small-size engine cogeneration system, regarding Japanese standard JIS B-8122 and international standard organization, ISO-8528, was applied to the system. The evaluation methods, start-test, rapid-load-up and rapid-load-down, etc. were executed at the system, and reasonable results were acquired. The electrical and thermal efficiencies were executed and analyzed at various load conditions. The NOx emission at various load condition was also measured. Finally, the gas engine cogeneration system was installed to a site for actual usage and it was continually operated during more than 6 months as the site condition.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.2-4
• /
• 2014

The preferred dimensions of the test opening for a window are $1250mm{\times}1500mm$ according to ISO 10140-1:2010. But tests done at actual size generally because not standardized for windows. In this study, we know the sound insulation characteristics by the size of windows using the single windows and double windows, consider the more effective performance evaluation method.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2007.04a
• /
• pp.739-744
• /
• 2007

Wind loads for cladding can be estimated using the maximum wind pressure including gust effects from wind-tunnel tests. However, when estimating the maximum wind pressure with gust effects, wind pressure coefficients for cladding would be different according to the averaging time of wind pressures, In the paper, for wind pressures obtained from wind-tunnel tests for apartment buildings, whose window panes were damaged by actual strong wind, it was investigated how pressure coefficients varied according to the size of cladding and averaging time using TVL method of Lawson. In result, it was found that the lesser the size of cladding and averaging time were, the larger pressure coefficients became. Accordingly, to estimate wind loads for cladding of apartment buildings and design it, the averaging time of wind pressures should be considered properly.

• Journal of the Korea Institute of Building Construction
• /
• v.19 no.3
• /
• pp.229-237
• /
• 2019

This study examines the estimation of strength through a ultra-high strength concrete mock-up specimen using the rock compressive strength test hammer. According to the test result, the commonly used strength estimation formulae showed differences among them when the data of this test were applied. In additional, it show that these formulae underestimated the actual measurements further when the compressive strength was 30MPa or greater and deviated the distribution range of actual measurements in all strength ranges. The rock test hammer showed a higher correlation than type N Schmidt hammer regardless of the direction of hit for each type of W/B and the inclusion of coarse aggregate, and mortar showed a little higher correlation than concrete. As a result, it can be suggested that the coefficient of variation and the standard deviation of the mortar(2.26%/1.36) are lower than those of the concrete(4.06%/2.5), and the smaller the size of the coarse aggregate, the smaller the coefficient of variation and the more accurate the value.

• The Research Journal of the Costume Culture
• /
• v.8 no.2
• /
• pp.272-281
• /
• 2000

The purpose of this study is to provide for the basic data useful to the effective production. For this purpose, 180 Korean mothers who bring up from newborns to four-year-old babies were sampled to survey the problems on size occurred by wearing and purchasing the Infants'Wear and positively identify the factors affecting the fitness. Data is processed by a computer(SAS) and analyzed by using frequency, perentage, mean, χ²-test, Duncan-test. The main results of this study are as follows ; 1. Consumers'awareness of sizing system of Infant's wear tent to present relatively high and tend to purchase their infants'wear larger than actual sizes or that consumers'preferences depend little on size adaptation. 2. As a result of analyzing the part not fit, neck circumference, waist circumference, total length, neck back-waist length is short, sleeve length, pants length, shoulder length is big. In all, it has been found through this study that fitness and awareness of sizing system of Infant's Wear in purchasing infants'wear was influenced by many external factors. Therefore, in order to maximize the size adaptability for infants, Infants'Wear must be present the reasonable sizes and specifications for infants'wear in consideration of domestic and foreign specifications and infants'health condition.

• Journal of Korean Society for Atmospheric Environment
• /
• v.15 no.6
• /
• pp.799-804
• /
• 1999

Particle collection characteristics of the MOUDI cascade impactor has been studied for coarse particles in the range of 2 to 20$mu extrm{m}$ in aerodynamic diameter. A vibrating orifice aerosol generator was empolyed to generate monodisperse test aerosols. The oleic acid and sodium chloride(NaCl) particles were used as test aerosols. Aluminum foil and Teflon filter were selected as impaction media. The sampling flow rate was changed from 25 to 35L/min. Particle collection efficiency for single stage was examined for liquid particles. The stage response was obtained experimentally for the cascade impactor composed of three stages and a backup filter. The results showed that most of particle collection efficiencies measured in this work are similar to the efficiency curves obtained by Marple et al.(1991). For particles less than cut-off size of the stage, the collection efficiencies of solid particles are similar to those of loquid particles. However, the collection efficiency of solid particles decreases with mereasing particle diameter for the particles greater than the actual cut-off size of the impactor. The particle collection efficiency increases with increasing sampling flow rate at the same particel size. However, the collection efficiency curves seem not to be greatly shifted with the flow rate. The stage responses obtained by direct measurements in this work are in good agreement with those derived from the collection efficiency curves for single stage.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.1
• /
• pp.143-149
• /
• 2016

This study evaluated the shear behavior of geogrid reinforced ballast material using a large scale direct shear test and discrete element method (DEM) based on PFC 3D program. The direct shear test was conducted on ballast materials that have different particle size distributions. Whereas the test results revealed that the shear strength generally increased with the larger particle size of ballast material without geogrid reinforcement, the shear behavior of ballast material was found to change pertaining to the relationship between particle size distribution and geogrid rib size. Generally, it is deemed the effectiveness of reinforcement can be achieved when the rib size is two times greater than average particle size. A numerical analysis based on DEM was conducted to verify the test results. The geogrid modeling was successfully completed by calibration process along with sensitivity analysis to have actual tensile strength provided by manufacturer. With a given geogrid model, the parametric evaluation was further carried out to examine the interactive behavior between geogrid and ballast material. Consequently, it was found that the effectiveness zone of geogrid reinforcement generated within a specific depth.