• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.1
• /
• pp.37-42
• /
• 2012

This study was carried in order to manufacture the high quality coated paper. High quality includes not only physical and optical properties of coated paper but also final print quality. In this study, new acrylic-styrene emulsion was polymerized in laboratory and compared with conventional styrene-butadiene latex. Low-shear viscosity of coating color was decreased with increasing acrylic-emulsion dosage. Small amount of acrylic emulsion addition increased water retention, but further addition decreased it. Acrylic-emulsion addition improved paper gloss, brightness and whiteness, but decreased PPS and opacity slightly. Ink gloss was increased with using No. 3 acrylic-emulsion due to lower ink setting properties. However No. 1 and 2 emulsion showed the opposite result. Surface strength of coated paper was increased with using No. 3 acrylic-emulsion. These results indicate that high quality coated paper can be manufactured with using No. 3 acrylic-emulsion.

• Korean Chemical Engineering Research
• /
• v.50 no.5
• /
• pp.789-794
• /
• 2012

For the purpose of development of the latex suitable for polymer cement mortar, experiments on the preparation of carboxylated styrene butadiene latex by the method of the two-step emulsion polymerization were performed. Methyl methacrylate, methacrylic acid and acrylic acid were selected as carboxylic co-monomer, styrene and butadiene as monomer, sodium dodecylbenzene sulfonate and sodium salt of lauryl sulfonate as anionic emulsifiers, and nonylphenoxy poly (ethyleneoxy) ethanol (n=10, 20, 40) as latex stabilizer. Potassium persulfate and sodium bisulfite were also used as redox initiator, and sodium monohydrogen phosphate and potassium carbonate as electrolytes. The effects of categories and concentration of carboxylic co-monomer, molecular weight control agent, crosslinking agent, and styrene/butadiene monomer ratio on the characteristics of latex were investigated. Polymerization recipes for preparation of polymer cement mortar could be proposed. The prepared latexes were tested for the physical properties such as compressive and flexural strength when latexes were mixed with cement mortar. The results showed that the latex could be adapted to polymer cement mortar. Also, it was recognized that the compressive and flexural strength were exhibited 25.4% and 45.3% respectively higher improvement than the quality standards at 28 days curing time.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.04a
• /
• pp.339-347
• /
• 2011

This study was carried out in order to manufacture the high quality coated paper. High quality coated paper includes not only present state but also the state of the future. So in this study, acrylic-styrene emulsion which polymerized in laboratory was compared with SB(Styrene-butadiene) latex during thermal aging. The coated paper with three different formulations which controlled the dosage of acrylic-styrene emulsion were prepared. The coated paper were thermally aged at $105^{\circ}C$ for 18days and the optical properties were measured. Brightness, whiteness and CIE L value were higher during thermal aging with increasing amount of acrylic-styrene emulsion. CIE $a^*$ value was higher and CIE $b^*$ value decreased with increasing amount of acrylic-styrene emulsion. These results indicate that high quality coated paper which has anti -thermal aging property can be manufactured with acrylic-styrene emulsion.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.1
• /
• pp.69-75
• /
• 2004

In this study, various model composite latexes were synthesized using n-butyl acrylate and methyl methacrylate as comonomers by seeded multi-staged emulsion polymerization. Monodispersed model composite latex particles with size of 190 nm and polydispersity index of 1.05, which have various morphology including random copolymer particle, soft-core/hard-shell particle, hard-core/soft shell particle, and gradient-type copolymer particle, homopolymers particles were prepared. The designed morphology of model composite particles were confirmed.

• Journal of the Korean Applied Science and Technology
• /
• v.19 no.2
• /
• pp.131-136
• /
• 2002

As model waterborne acrylic coatings, mono-dispersed poly(butyl acrylate-methyl methacrylate) copolymer latexes of random copolymer and core/shell type graft copolymer were prepared by seeded multi-staged emulsion polymerization with particle size of $180{\sim}200$ nm using semi-batch type process. Sodium lauryl sulfate and potassium persulfate were used as an emulsifier and an initiator, respectively. The effect of particle texture including core/shell phase ratio, glass transition temperature and crosslinking density, and film forming temperature on the film formation and final properties of film was investigated using SEM, AFM, and UV in this study. The film formation behavior of model latex was traced simultaneously by the weight loss measurement and by the change of tensile properties and UV transmittance during the entire course of film formation. It was found that the increased glass transition temperature and higher crosslinking degree of latex resulted in the delay of the onset of coalescence of particles by interdiffusion during film forming process. This can be explained qualitatively in terms of diffusion rate of polymer chains. However, the change of weight loss during film formation was insensitive to discern each film forming stages-I, II and III.

• Journal of Adhesion and Interface
• /
• v.13 no.3
• /
• pp.109-115
• /
• 2012

Monodisperse blue-colored poly(styrene-co-acrylic acid) latices were successfully prepared by seeded emulsion polymerization. Blue-colored latices with carboxyl anionic charge on the surface were synthesized at the second stage with the introduction of Blue 606 dye, acrylic acid, and 0.21 ${\mu}m$-polystyrene seed. All the blue-colored latices synthesized in this study were in the size range of 0.25~0.42 ${\mu}m$ and all uniform with less than 1.01 in PSD. The particle size increased with the addition of acrylic acid being delayed and colloidally stable latices were obtained over 30 min after its addition. The blue-colored latex with 20 wt% acrylic acid showed -145 mV of zeta-potential and $-9.4{\times}10^{-6}\;cm^2/Vs$ of electrophoretic mobility, and with 25 wt% of DVB showed high $T_g$ at 396.7 K.

• Textile Coloration and Finishing
• /
• v.11 no.4
• /
• pp.50-56
• /
• 1999

The adhesive properties of polyester cord in rubber matrix were investigated according to the surface modification. The polyester cord was oxidized in sodium hypochlorite solution, and graft-polymerized with acrylic acid under the irradiation with ultraviolet light, and then coated with resorcinol-formaldehyde latex (RFL). The modified surface was checked with scanning electron microscope. The adhesive properties were measured by the full-Out method, and evaluated with regard to the energy of adhesion and the maximum load. The polyester was not oxidized in sodium hypochlorite solution, so the surface was not able to etch to produce the coarse topology. As the concentration of acrylic acid and the reaction time were increased, the graft yields were also increased. It was considered that the acrylic acid would swell the polyester and diffuse easily to the inner side of substrate. The adhesive properties of polyeser to rubber matrix were affected by the surface condition. Namely, the maximum load was almost same, but the energy of adhesion was rather higher In the polyester grafted with acrylic acid than in control one. We concluded that the flexible aliphatic chains of polyacrylic acid situated in the interface of cord and rubber matrix were distributed well the stress and strain all over the filler resulting the high energy of adhesion.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.758-762
• /
• 1998

In preparing void latex particles by emulsion polymerization, the weight mean particle size of which is ranged $0.3{\mu}m{\sim}1.5{\mu}m$, reaction parameters were investigated in order to elucidate their effects on the size distribution and the solid content of emulsion polymer. Experimental results showed that the weight mean particle size of hydrophillic core polymer was reduced as the concentration of sodium dodecylbenzene sulfonate (SDS) increased. The size of void polymethyl-methacrylate-polystyrene composite latex particles became larger as the concentration of styrene monomer and the sodium persulfate increased. However, the size of void latex particles was reduced as the feeding rate of acrylic acid increased. The solid content of emulsion polymer was strongly dependent on the addition of stylene monomer. By increasing the concentration of styrene monomer the solid content of emulsion polymer increased linearly.

• Journal of the Korean Applied Science and Technology
• /
• v.21 no.3
• /
• pp.259-266
• /
• 2004

Film properties of monodispersed model composite latexes with particle size of 190 nm, which consist of n-butyl acrylate as a soft phase monomer and methyl methacrylate as a hard phase monomer with different morphology was examined. Five different types of model latexes were used in this study such as random copolymer particle, soft-core/hard-shell particle, hard-core/soft-shell particle, gradient type particle, and mixed type particle. Tensile strength and tensile elongation at break of final films were evaluated. Those properties can be interpreted in terms of PBA/PMMA phase ratio and their morphology. The interfacial adhesion strength was also evaluated using $180^{\circ}$ peel strength measurement and cross hatch cutting test.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.10a
• /
• pp.513-518
• /
• 2002

In vertical construction joint, adhesives such as epoxy, acrylic, latex, etc. have been usually used for bonding fresh concrete to hardened concrete. In this study, performance of adhesives under various application conditions was investigated through tests for slant shear and flexural strength. From the results of the tests, it is found that superior bonding performance can be obtained under good surface preparation without adhesive when high strength concrete is used.