• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.1292-1297
• /
• 2004

Acoustic characteristics in an industrial gas-turbine combustor are numerically investigated by adopting linear acoustic analysis. Spatially non-homogeneous temperature field in the combustor is considered in the numerical calculation and the characteristics are analyzed in view of acoustic instability. Acoustic analysis are conducted in the combustors without and with acoustic resonator, which is one of combustion stabilization devices. It has been reported that severe pressure fluctuation frequently occurs in the adopted combustor, and the measured signal of pressure oscillation is compared with the acoustic-pressure response from the numerical calculation. The numerical results are in a good agreement with the measurement data. In this regard, the phenomenon of pressure fluctuation in the combustor could be caused by acoustic instability. The acoustic effects of the resonators are analyzed in the viewpoints of both the frequency tuning and the damping capacity.

• 한국음향학회지
• /
• 제15권6호
• /
• pp.52-58
• /
• 1996

음파와 진동에너지를 활용하는 음파기술의 응용 연구분야로 음향공진 및 맥진동 현상을 이용하여 기액상에서 산소절달효율을 극대화 할 수 있는 폐수처리용 음향공진 산기관의 개념을 제안하였으며 원리와 성능시험을 수행하였다. 또한 저압용 헬름흘쯔 공진기, 실린더형 및 고리형 반사공진기 그리고 복합 공진시스템의 설계개념과 원리를 구현하였다. 물질전달 과정을 촉진하는 음향공진 에너지는 산소전달효율을 높여주며, 노즐에서 분출하는 공기 제트의 불평형에 의해 발생하는 주기적인 맥진동 현상은 미세한 공기방울을 만들어 내는데, 이 두가지 원리가 가장 잘 적용되는 고리형 반사공진기(AJR)의 성능이 가장 우수한 것으로 평가되었으며 기존의 산기관 보다도 $20{\sim}30%$ 정도 높은 효율을 실험으로 확인하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.350-354
• /
• 2008

Low frequency exhaust noise of marine diesel engine is one of the most important noise sources in vessels. However, conventional absorptive silencers are limited because the absorptive material is not effective in low frequency range. In the paper, exhaust noise control of marine diesel engine has been studied by using the resonator type silencer, which was composed of concentric hole-cavity resonators. The acoustic performance of the resonator type silencer was verified by the insertion loss measurement considering flow effect. Consequently, its high performance, about $5{\sim}8dB$ noise reduction, in the low frequency range was confirmed by insertion loss measurements conducted in the ship.

• 전기학회논문지
• /
• 제56권5호
• /
• pp.915-920
• /
• 2007

AIN-based film bulk acoustic resonator (FBAR) devices which adopt a membrane-type configuration such as Mo/AIN/bottom-metal/Si are fabricated by employing a novel process. The proposed resonator structure does not require any supporting layer above the substrate, which leads to the reduction in energy loss of the resonators. For all the FBAR devices, the frequency response characteristics are measured and the device parameters, such as return loss and input impedance, are extracted from the frequency responses, and analyzed in terms of the various metals such as Al. Cu, Mo, W used in the bottom-electrode. The mass-loading effect caused by the used bottom-electrode metals is found to be the main reason for the difference revealed in the measured characteristics of the fabricated FBAH devices. The results obtained in this study also show that the degree of match in lattice constant and thermal expansion coefficient hetween piezoelectric layers and electrode metals is crucial to determine the device performance of FEAR.

• 한국전기전자재료학회논문지
• /
• 제18권2호
• /
• pp.164-168
• /
• 2005

Piezoelectric ZnO thin films were for the first time formed on SiO$_2$/Si(100) substrate using 2-step deposition, atomic layer deposition(ALD) and RF magnetron sputtering deposition, for film bulk acoustic resonator(FBAR) applications. The ZnO buffer layer by ALD was deposited using alternating diethyl zinc(DEZn)/$H_2O$ exposures and ultrahigh purity argon gas for purging. The ZnO films by 2-step deposition revealed stronger c-axis-preferred orientation and smoother surface than those by the conventional RF sputtering method. The solidly mounted resonator(SMR)-typed FBAR fabricated by using 2-step deposition method revealed higher quality factor of 580 and lower return loss of -17.35dB. Therefore the 2-step deposition method in this study could be applied to the FBAR device fabrication.

• 한국군사과학기술학회지
• /
• 제12권1호
• /
• pp.106-113
• /
• 2009

This paper presents a surface acoustic wave(SAW) micro-electro-mechanical-systems(MEMS) interdigital transducer (IDT) gyroscope with 80MHz central frequency on a $128^{\circ}\;YX\;LiNbO_3$, which is consisted of a two-port SAW resonator, metallic dots and dual delay lines for the sensor and reference oscillators. Reason for using two delay line oscillators is to extract the gyroscope effect by comparing the resonant frequencies between two oscillators and to compensate the temperature effect. Based on the coupling of modes(COM) simulation, an 80MHz two ports SAW resonator and dual delay line were fabricated and characterized by the network analyzer. Obtained sensitivity was $109Hz/deg{\cdot}s^{-1}$ in the angular rate range of $0{\sim}1000deg/s$. Good Linearity and superior directivity were observed.

• 정보저장시스템학회논문집
• /
• 제3권4호
• /
• pp.196-201
• /
• 2007

As the demand for the lap-top computer has been increased, most users ask quiet environment to work comfortably. Therefore, noise problems of an ODD are of great interest. For the high speed ODD, the flow induced noise is caused by the turbulent flow[1], which is known to be a major source of overall noise of a slim type ODD. In this study, we introduce a new attempt to reduce the noise level using the concept of Helmholtz resonator[2].The experimental analysis is carried out for several cases at different resonance frequencies and different hole patterns. The results show reductions in the noise level from the acoustic noise absorption point of view.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.1238-1243
• /
• 2002

In this study, the validity of the acoustic impedance model and the estimation model by electro-acoustic analogy suggested by Maa for predicting the absorptive performance of multiple layer perforated plate systems is investigated. From the comparison between the experiment and calculation for the absorption performance of double layer perforated plate system, the calculated results of using Rao and Munjal's impedance model and transfer matrix method are closer to the experimental values than those of using Maa's impedance model and electro-acoustic analogy. Therefore, in order to apply the acoustic impedance model and the estimation model by electro-acoustic analogy suggested by Maa to the multiple layer perforated plate systems, it is necessary that the suggested acoustic impedance and estimation models should be re-examined.

• 한국소음진동공학회논문집
• /
• 제22권8호
• /
• pp.756-762
• /
• 2012

A method of the low-frequency noise reduction in an enclosure by using an array of Helmholtz resonator is presented. An integral form of equation, which represents the acoustical coupling between the internal sound field and the resonator array, is formulated so that the boundary element method can be applied to solve the coupling problem. It is shown that the resonator array on the surface of the enclosure can be regarded as impedance patches on the boundary element. Experiments on a simple enclosure acoustically coupled with an array of resonators are conducted to verify the method. The predicted noise reduction by the boundary element method shows good agreement with the measured one. The effects of the resistance of resonators as well as the number of resonators on the noise reduction are demonstrated. As a practical example, the presented method is applied to the payload fairing of a space launcher with resonator arrays. It is demonstrated that the resistance of resonators affects significantly the required number of resonators to achieve a desired noise reduction.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2009년도 춘계학술대회 논문집
• /
• pp.107-110
• /
• 2009

연소불안정현상은 주로 음향파와 열방출률 섭동간의 상호작용에 의해 발생한다고 알려져 있다. 이러한 현상은 헬름홀츠 공진기와 같은 수동제어기를 사용하여 감소시킬 수 있다. 그러나 헬름홀츠 공진기는 일반적으로 좁은 주파수대역에 대해서만 효과가 있는 단점을 가진다. 따라서 본 연구에서는 다양한 작동 범위에서 효과를 가질 수 있도록 피스톤을 사용하여 헬름홀츠 공진기의 부피를 변화시켜가며 연소불안정현상에 적용하였다. 그 결과 피스톤을 최적위치에 동조시킴으로써 연소 불안정 모드의 진폭을 감소시킬 수 있었다. 또한 이러한 결과를 바탕으로 능동적으로 동조되는 수동제어방식의 가능성에 대해서 알아보고자 한다.