• 한국정밀공학회지
• /
• 제12권9호
• /
• pp.74-85
• /
• 1995

The purpose of this paper is to evaluate the grade of WA vitrified and resinoid bond grinding wheels by the sue of AE measuring system. When the manufactured 48 kinds of specimens were scratched by the method of OKOSHI'S grade test, the relationship between the amount of bit scratch depth of grinding wheel specimens and the character- istics of AE signals, and the relationship of AE counts and grade were considered as fololws; (1) The higher the grades are AE cumlulative event counts N and AE event count rate n, the smaller the values tend to be. But A $E_{rms}$is in reverse. (2) In the case of same grade, the smaller the grain size is, the higher the value of AE cumulative event counts N and A $E_{rms}$is results of comparison and observation. The grinding wheel with lower elasticity and with higher percentage of pore detected higher value of AE cumula- tive event counts N than with higher elasticity and lower percentage of pore. But A $E_{rms}$ is in reverse. (3) AE cumulative event counts N and bit scratch depth h have normally one to one correspondence. (4) It can be expected that quantitative evaluations of grade by using AE have been carried out by the wave observation of AE signal in line with the relationship between load speed of bit and AE cumulative event counts N & AE event count rate n.' AE event count rate n.ate n.

• 한국재료학회지
• /
• 제3권4호
• /
• pp.361-371
• /
• 1993

응력부식균열(SCC) 감수성평가를 위한 여러 시험방법들중 저변형율시험방법은 비교적 \ulcorner은 시간내에 금속재료의 SCC감수성을 평가하기 위한 효과적인 시험방법이다. 그러나 저변형율 시험방법만으로 SCC과정의 미시적 파괴거동ㅇ르 분석하는 것은 매우 어렵다. 종래, 음향방출(AE)시험은 재료의 파괴과정시 미시균열의 개시 및 전파거동을 감시하는데 유효한 기법으로 잘 알려져 있다. 그러므로 본 논문에서는 저변형율시험과 음향방출시험을 이용하여 SCC의 전파과정과 AE신호 특성사이의 상호관계를 분석하였다. 실험결과, 재료의 미시파괴 과정에서 발생하는 AE신호들은 뚜렷히 시험환경에 의존하였으며, 인공해수중에서 SCC과정시 발생된 AE신호 특성은 Air상태 보다 상당히 크게 나타났다. 그리고 SCC거동은 AE신호의 진폭인자로서 명확하게 평가할 수 있다.

• 한국정밀공학회지
• /
• 제9권2호
• /
• pp.122-127
• /
• 1992

In this study, we investigated defects of graphite by three NDT methods which are ultrasonic testing at 5 MHz, micro-forused X-ray testing and AE testing. As the detection of AE signals generated from graphite tensile specimens, we calculated location of AE sources and compared them with UT and X-ray test results in detecting defects of several specimens, Acoustic emission testing could be applied to some graphites which have fine grains of a few tens of micrometer, but it was difficult to those in lager grain of few fo milimeter. Also, we could understand what kind of defects has affected on tensile fracture of graphite.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1993년도 한국자동제어학술회의논문집(국제학술편); Seoul National University, Seoul; 20-22 Oct. 1993
• /
• pp.307-311
• /
• 1993

Research concerning gears included in rotating machines has been reported using the acoustic emission (AE) method, however, almost no research has been conducted using the AE method in regard to running gears in a bending fatigue processor spur gear teeth. Therefore, in this report, a power circulating-type gear testing machine was used and AE signals and crack length were measured in the bending fatigue process of case-hardened spur gear. Furthermore, the envelope of the AE signal was detected and various analysis were carried out in this data. In the course of the experiments, the following results were observed : the AE signal envelope consists mainly of contact frequency component and twice as many as this;two peaks of AE appear in each tooth contact by the tip corner contact ; as a result of the severe tip corner contact ; as a result of the severe tip corner contact with the sudden increase of crack length, AE signal becomes large.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1993년도 추계학술대회 논문집
• /
• pp.70-75
• /
• 1993

Chatter vibration is an unwanted phenomenon in metal cutting and it always affects surface finish, tool life machine life and the productivity of machining process. The In-process monitoring & control of chatter vibration is necessarily required to automation system. In this study, we constructed the multi-sensing system using Tool Dynamometer,Accelerometer and AE(Acoustic Emission) sensor for the credible detection of chatter vibration. And a new approach using a neural network to process the features of multi-sensor for the recognition of chatter vibration in turning operation is proposed. With the back propagation training process, the neural network memorize and classify the feature difference of multi-sensor signals.

• Macromolecular Research
• /
• 제9권1호
• /
• pp.20-29
• /
• 2001

Interfacial adhesion and nondestructive behavior of electrodeposited (ED) carbon fiber rein-forced composites were evaluated using electro-micromechanical techniques and acoustic emission (AE). The interfacial shear strength (IFSS) of the ED carbon fiber/epoxy composites was higher than that of the untreated fiber. This might be expected because of the possibility of chemical or hydrogen bonding in an electrically adsorbed polymeric interlayer. The logarithmic electrical resistivity of the untreated single-carbon fiber composite increased suddenly to infinity when fiber fracture occurred, whereas that of the ED composite increased relatively gradually to infinity. This behavior may arise from the retarded fracture time due to enhanced IFSS. In single- and ten-carbon fiber composites, the number of AE signals coming from interlayer failure of the ED carbon fiber composite was much larger than that of the untreated composite. As the number of the each first fiber fractures increased in the ten-carbon fiber composite, the electrical resistivity increased stepwise, and the slope of the logarithmic electrical resistance increased.

• 대한기계학회논문집A
• /
• 제25권9호
• /
• pp.1391-1399
• /
• 2001

The AE measurement is one of the most convenient methods for detecting contacts between the slider and the disk. The AE method has been widely used in the investigation of the tribology of sliding interfaces due to its convenience. We examined the relationship between the AE signal and the flying height of a slider. We investigated the influence of the disk linear velocity on the AE rms signal by using the AE measurement system. The experiment also gives the relationship between the take-off velocity and the disk surface conditions. To investigate the behavior of the slider further, the variances of the AE signals are analyzed. The experimental results indicate that the increase in the magnitude of the AE rms signal does not necessarily mean the slider/disk contacts.

• 대한기계학회논문집A
• /
• 제30권10호
• /
• pp.1179-1186
• /
• 2006

This paper was designed to assess the adhesive properties of hard coatings on non-nitrided and nitrided various tool steels. Estimations of adhesion were done to scratch test which is mainly used in hard coating. The critical load$(L_c)$ between coating and substrate is defined through analysis of frictional load vs. normal load curve, signals of acoustic emission and optical observations. Coatings employed in this study are TiN, CrN and TiAlN, tools as substrates are STD11, STD61 and SKH51. It was classified to substrates with/without intermediate nitrided layer and hard coatings on substrate were deposited by arc PVD. Results showed that harder substrates and coatings give higher values of critical loads.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 춘계학술대회논문집
• /
• pp.319-323
• /
• 2007

Acoustic emission (AE) was originally developed for non-destructive testing of static structure, but over the year its application has been extended to health monitoring of rotating machines and bearings. It offers the advantage of earlier defect detection in comparison with monitoring bearing. This study was diagnosed low-speed machine which had a fault bearing for early detection by AE. And the artificial faults in a experimentation bearing was made for the bearing signals from difference speed and load were compared and analyzed by AE.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2003년도 하계 학술대회 논문집
• /
• pp.469-477
• /
• 2003

삼림에서 벌채된 목재는 대부분 건조공정을 거쳐 산업용 재료가 되므로 건조정도에 따라 목질 재료의 품질이 결정된다. 목재에 포함된 과도한 수분을 제거하여 운송비용을 줄일 수 있으며 목재를 적절하게 건조하게 되면 목재 사용 중에 발생할 수 있는 수축 및 팽윤을 제한할 수 있을 뿐만 아니라 건조과정을 통해 비틀림, 갈라짐, 할열 등과 같은 결함의 발생을 크게 줄일 수 있다. 또한 건조된 목재는 생재에 비해 기계 가공이 보다 용이하기 때문에 정확한 치수로 재단이 가능하며, 각각의 부품으로 재단한 부재를 못이나 나사못, 볼트, 접착제 등을 사용하여 견고하게 짜 맞출 수 있다. 그리고 도장성능이 향상되어 기능성을 증진시킬 수 있으며, 건조 후의 방부처리를 통해 장기간의 사용이 가능하다. (중략)