• 한국의류산업학회지
• /
• 제3권5호
• /
• pp.486-491
• /
• 2001

The purpose of this study was to examine the effects of chemical finishes on performance characteristics of microfiber blend fabrics. A 60% polyester microfiber/40% cotton blend woven fabric was finished by ten chemicals: three silicone softeners, one fluorochemical, and their mixtures. Performance characteristics examined were abrasion resistance, and oil/water repellency. Chemical finishes containing dimethylpolysiloxane silicone performed better in fabric abrasion resistance than other chemicals. The correlation between abrasion wear and instrumental measures of fabric hand indicated that the breaking strength loss by abrasion related negatively to the coefficient of friction. This implied that the finished fabrics with lower surface frictional coefficient (slipperier) had higher breaking strength loss by abrasion. The microfiber structure of polyester did not appear to help in oil/water repellency due to the larger surface areas of the microfibers. The fluorochemical finished fabric had the most significant improvement on oil/water repellency. The silicone-only finishes, however, did not improve oil/water repellency. When mixed with the fluorochemical, silicone finishes showed improved oil/water repellency.

• Advances in concrete construction
• /
• 제8권2호
• /
• pp.127-137
• /
• 2019

Roller Compacted Concrete (RCC) is a zero slump concrete consisting of a mixture of cementitious materials, sand, dense graded aggregates and water. In this study, an attempt has been made to investigate the effect of aggregate type on strength and abrasion resistance of RCC made by using granulated blast furnace slag (GGBS) as partial replacement of cement. Mix proportions of RCC were finalized based upon the optimum water content achieved in compaction test. Two different series of RCC mixes were prepared with two different aggregates: crushed gravel and limestone aggregates. In both series, cement was partially replaced with GGBS at a replacement level of 20%, 40% and 60%. Strength Properties and abrasion resistance of the resultant mixes was investigated. Abrasion resistance becomes an essential parameter for understanding the acceptability of RCC for rigid pavements. Experimental results show that limestone aggregates, with optimum percentage of GGBS, perform better in compressive strength and abrasion resistance as compared to the use of crushed gravel aggregates. Observed results are further supported by stoichiometric analysis of the mixes by using basic stoichiometric equations for hydration of major cement compounds.

• 대한치과보철학회지
• /
• 제34권3호
• /
• pp.464-474
• /
• 1996

A principal advantage of a plastic tooth over a porcelain tooth should be its ability to bond to the denture base material. But plastic teeth could craze and wear easily, so more abrasion resistant plastic denture teeth have been developed. To resist abrasion, the degree of cross-linking was increased, but bonding to denture base meterial became more difficult. The purpose of this study was to evaluate the bond strength of plastic teeth and abrasion resistant teeth bonded to heat-curing, self-curing and light-curing denture base material. Denture tooth molds were chosen that had a>8mm diameter. The denture teeth was bonded to three denture base materials and then machined to the same dimensions. Three denture base materials were used as control groups. Prior to tensile testing, the specimens were thermocycled between $5^{\circ}C\;and\;55^{\circ}C$ for 1000cycles. Tensile testing was performed on an Instron Universal testing mechine. Experimental group ; plastic teeth(Justi Imperial)+heat-curing resin(Lucitone 199) plastic teeth(Justi Imperial)+light-curing resin(Triad) plastic teeth(Justi Imperial)+self-curing resin(Vertex SC) abrasion resistant teeth(IPN)+heat-curing resin(Lucitone 199) abrasion resistant teeth(IPN)+light-curing resin(Triad) abrasion resistant teeth(IPN)+self-curing resin(Vertex SC) Control group ; heat-curing resin(Lucitone 199) light-curing resin (Triad) self-curing resin(Vertex SC). The results were as follows : 1. The denture teeth bonded to heat-curing resin showed the cohesive failure and those bonded to the other resins showed adhesive failure. 2. Tensile bond strength of the plastic teeth bonded to self-curing resin was not significantly greater than bonded to light-curing resin(p>0.05). 3. Tensile bond strength of the abrasion resistant teeth bonded to self-curing resin was not significantly greater than bonded to light-curing resin(p>0.05). 4. Tensile bond strength of the plastic teeth to self-curing resin was not significantly different from that of the abrasion-resistant teeth(p>0.05). 5. Tensile bond strength of the plastic teeth to light-curing resin was significantly greater than that of the abrasion resistant teeth(p<0.01).

• 한국농공학회논문집
• /
• 제57권5호
• /
• pp.19-27
• /
• 2015

The results of Saemangeum seadike field inspection and material testing of armor stones in order to analyze causes of abrasion according to material characteristics of seaside armor stones in Saemangeum seadike are in the following: 1. The armor stones in Saemangeum seadike have been constructed by using internal stones (mainly, sinsi stones) and external stones, which had less strength (77.3 %) and more abrasion rate (133.3 %) compared with sinsi stones. 2. The compressive strength and abrasion rate were compared between ordinary wave section and high wave section for the purpose of analyzing the influence of waves. In compressive strength, sinsi stones were 4.0 % stronger and external stones were 0.6 % stronger in ordinary wave section than those of high wave section in average. In the case of abrasion rate, sinsi stones were 3.0 % higher and external stones were 8.2 % higher in the high wave section than those in the ordinary section. 3. The result of comparing compressive strength according to a zone is that the compressive strength in the Intertidal area was less strong in most of the zones. 4. Considering that deviated stones are moving around over the surface of armor stones in situ, it is important to compare material characteristics. So the comparison test about this factor showed that deviated sinsi stones were stronger than armor stones in situ in terms of compressive strength and resistance to abrasion. Based on these results, abraded armor stones may have resulted from their durability. Therefore it is assumed that armor stones are likely to be abraded when deviated stones which are more durable are moving around over armor stones which are less durable.

• 대한소아치과학회지
• /
• 제29권2호
• /
• pp.210-216
• /
• 2002

Air-abrasion 기술은 입자의 운동에너지를 이용하여 비기계적인 방법으로 치아를 처리하거나 치아표면에 존재하는 착색이나 치석을 제거하는 방법으로서, 환자의 불안이나 불편감을 증가시킬 수 있는 압력, 진동이나 열의 발생이 적고 건전한 치질의 보존이 용이하며 특히 소아환자에서 마취의 필요성을 감소시키고 시술부위에서의 타액오염을 가능성을 줄여주고 건조한 시술부위 유지에 용이하고 수복재의 결합력을 증가시켜주는 등의 여러 장점을 지니고 있어, 복합레진을 위한 와동형성, 열구전색을 위한 치아형성, 산 부식 대신 또는 산부식전 치아표면의 처리, 초기 우식증의 진단 등에 이용될 수 있다. 본 증례는 유중절치의 인접면 우식치료, 유구치의 교합면 우식치료, 제1대구치의 우식치료 및 우식 예방을 air abrasion 기술을 사용하여 수복한 바, 환자의 행동조절 및 시술부위의 완전한 건조가 어려운 소아환자에게 있어 임상적으로 유용하다고 여겨지며 양호한 결과를 얻었기에 보고하는 바이다.

• 한국표면공학회지
• /
• 제50권5호
• /
• pp.345-351
• /
• 2017

A double-layered anti-reflective coating with hydrophilic/abrasion-resistant properties was studied using anatase titanium dioxide($TiO_2$) and silicon oxycarbide($SiO_xC_y$) thin film. $TiO_2$ and $SiO_xC_y$ thin films were sequentially deposited on a glass substrate by DC sputtering and PECVD, respectively. The optical properties were measured by UV-Vis-NIR spectrophotometer. The abrasion-resistance and the hydrophilicity were observed by a taber abrasion tester and a contact angle analyzer, respectively. The $TiO_2/SiO_xC_y$ double-layer thin film had an average transmittance of 91.3%, which was improved by 10% in the visible light region (400 to 800 nm) than that of the $TiO_2$ single-layer thin film. The contact angle of $TiO_2/SiO_xC_y$ film was $6.9^{\circ}$ right after UV exposure. After 9 days from the exposure, the contact angle was $10.2^{\circ}$, which was $33^{\circ}$ lower than that of the $TiO_2$ single-layer film. By the abrasion test, $SiO_xC_y$ film showed a superior abrasion-resistance to the $TiO_2$ film. Consequently, the $TiO_2/SiO_xC_y$ double-layer film has achieved superior anti-reflection, hydrophilicity, and abrasion resistance over the $TiO_2$ or $SiO_xC_y$ single-layer film.

• 대한소아치과학회지
• /
• 제28권3호
• /
• pp.512-521
• /
• 2001

최근 air-abrasion기술이 새로운 법랑질 표면처리법으로 소개되고 있는데, 이것이 산부식 처리한 것보다 치면열구전색 전처리에 있어 더 나은 결과를 보이는지 연구할 목적으로, 저자들은 표면처리법 및 재료에 따른 미세누출도의 차이를 비교해 보고자 하였다. 9개의 군으로 나눈 시편치아에 산부식(1, 4, 7군), air-abrasion(2, 5, 8군), air-abrasion 후 산부식 (3, 6, 9군) 처리한 후 3종의 치면열구전색재($1\sim3$군 Teethmate-F, $4\sim6$군 Ultraseal XT plus, $7\sim9$군 : DenSeal)로 전색, 중합하여 색소침투도를 관찰하였으며, 각 시편의 전색재를 분리, 주사전자현미경으로 관찰하여 다음과 같은 결과를 얻었다. 1. 표면처리법에 따른 미세누출도는 air-abrasion군, 산부식군, air-abrasion 후 산부식군 순으로 작아졌다(p<0.05). 단, 7군과 9군간의 유의차는 없었다. 2. 미세누출도는 산부식군에서 7군 4군 1군 air-abrasion군에서 8군 5군 2군, air-abrasion후 산부식군에서 9군, 3군, 6군 순으로 작아졌으나, 각각 4군과 7군, 2군과 5군, 3군과 6군간의 유의차는 없었다. 3. SEM상에서, 산부식군은 비교적 긴 레진돌기가 규칙적으로, air-abrasion군은 짧은 레진돌기가 불규칙적으로, air-abrasion 후 산부식군에서는 이들이 혼재되어 있는 모습으로 관찰되었다.

• 한국염색가공학회지
• /
• 제29권1호
• /
• pp.18-24
• /
• 2017

Meta-aramid fabric has been widely used as the reinforcement of composites due to its high flame resistance and tearing strength. Functionality such as abrasion resistance of fabric is very important for specialty fabrics used in car racing suits. In this study, to improve abrasion resistance property of meta-aramid fabric, silicon deposition was conducted by utilizing RF magnetron sputtering. The sputtering process parameters effects were investigated as sputtering power and substrate temperature. The obtained results suggest that the silicon deposition on the meta-aramid fabric has obvious effect upon increasing the abrasion resistance, the thermal insulation and the electric resistance condition for silicon deposition was established. In conclusion, the results of this study have made it possible to manufacture meta-aramids with higher abrasion strength.

• 구강회복응용과학지
• /
• 제26권3호
• /
• pp.339-347
• /
• 2010

이전에 존재하던 컴포지트와 새로운 컴포지트 사이의 결합강도의 강화는 미세 기계적 유지를 증진하기 위한 표면 거칠기의 증가가 필요하다. 이 연구는 시효처리 후의 레진 컴포지트의 repair 결합강도에 다른 표면처리의 효과를 평가하는 것이다. 알루미늄 옥사이드를 이용한 air abrasion, chair-side silica coating한 그룹들에서 대조군과 불산 적용에 비하여 유의하게 높은 결합강도를 보였다. 레진 수복물의 repair시에 air abrasion의 사용은 필요한 것으로 보이며 부가적으로 silane의 적용은 결합강도에 긍정적 영향을 미치는 것으로 보인다.

• 한국의류학회지
• /
• 제28권1호
• /
• pp.112-118
• /
• 2004

Recently, as the percentage of women employment has been growing, the demand for various facilities and services regarding household duties and infant rearing is increasing and so do the amount of the disposable diaper used. Among the components of disposable diaper, the top sheet contacting with infant skin directly is usually made with nonwoven textiles. Therefore, the mechanical and surface characteristics of the nonwovens used in disposable diaper are important for the skin health of infants. In this study, we have explored the mechanical and surface properties, such as friction coefficient, fluid permeability and strength, of the nonwovens used for disposable diaper top sheet and observed the variation of their properties with abrasion cycles. Nonwoven materials examined in this study are 100% cotton spunlace, 100% tencel spunlace, 100% polypropylene (PP) thermal bonding and 100% PP air through (Thru-air bonded carded web). From the result of KES-F analysis, we've found that 100% PP air through type nonwoven had a low friction coefficient and showed a little change in surface properties as increasing abrasion cycles. Moreover, it revealed superior fluid permeability and quick-drying character. On the other hand, though showing an excellent absorption force, the spun lace type nonwoven made of 100% cotton and 100% tencel displayed relatively low abrasion strength especially in wetting condition.