• Progress in Superconductivity
• /
• 제11권1호
• /
• pp.47-51
• /
• 2009

For many large-scale applications of high-temperature superconducting materials, large critical current density ($J_c$) in high applied magnetic fields are required. A number of methods have been reported to introduce artificial pinning centers in $YBa_2Cu_3O_{7-{\delta}}$ films for enhancement of their $J_c$. We studied the microstructures and characteristic of $YBa_2Cu_3O_{7-{\delta}}$ films fabricated on $SrTiO_3$ (100) substrates with ZnO nanorods as pinning centers. Au catalyst nanoparticles were synthesized on STO substrates with self assembled monolayer to control the number of ZnO nanorods. The density of Au nanoparticles is approximately $240{\sim}260{\mu}m^{-2}$ with diameters of $41{\sim}49nm$. ZnO nanorods were grown on STO by hot-walled PLD with Au nanoparticles. Typical size of ZnO nanorod was around 179 nm in diameter and $2{\sim}6{\mu}m$ in length respectively. YBCO films deposited directly on STO substrates show the c-axis orientation, while YBCO films with ZnO nanorods exhibit any mixed phases without any typical crystal orientation.

• 한국재료학회지
• /
• 제14권11호
• /
• pp.764-768
• /
• 2004

Perovskite Pb(Mn_{1/3}Sbu_{2/3})O_2-Pb(Zr,Ti)O_3\;(PMS-PZT) was prepared and ZnO doping effects on its piezoelectric properties were investigated. Pyrochlore phase was not identified in the PMS-PZT ceramics with $0\sim5\;mol\%$ ZnO sintered at $1100^{\circ}C$ for 2 hrs, and maximum sintered density of $7.92 g/cm^3$ was obtained. Piezoelectric charge constant and voltage constant increased to $359{\times}10^{-12}\;C/N\;and\;22.5{\times}10^{-13}\;Vm/N$, respectively, with increasing ZnO content. Mechanical quality factor reduced considerably with increasing ZnO content. When the ZnO content was 3 $mol\%$, electromechanical coupling factor and relative dielectric constant showed maximum values of $56\%$ and 1727, respectively. This should be evaluated by complicated variations of sintered density, tetragonality of lattice, grain size, and A-site vacancy generated by ZnO addition and $Zn^{2+}$ substitution.

• 공업화학
• /
• 제8권3호
• /
• pp.446-453
• /
• 1997

광물인 금홍석과 공업용 $K_2CO_3$를 사용하여 $1000^{\circ}C$, 3시간 그리고 $K_2O$에 대한 금홍석의 몰비 2.0의 조건으로 초생상을 합성하였으며, 이를 비등수로 10시간 처리하여 중간상인 층상 구조의 사비탄산칼륨을 합성하였다. 그리고 중간상을 0.005M의 염산으로 30분 동안 처리하여 $KHTi_4O_9{\cdot}1.1H_2O$를 얻었으며, 이를 $400{\sim}600^{\circ}C$의 온도범위에서 열처리하여 길이 $10{\mu}m$, 직경 $0.2{\mu}m$의 팔티탄산칼륨을 합성하였다.

• Journal of Ginseng Research
• /
• 제27권1호
• /
• pp.37-42
• /
• 2003

인삼의 형질전환 시스템의 개발과 내병성관련 유전자의 도입에 관한 연구의 일환으로 soybean에서 cloning한 chitinase 유전자와 내병성 관련유전자(DR gene)가 식물에서 발현 및 형질전환될 수 있도록 운반체를 재조합하여 Agrobacterium을 이용해서 인삼에 형질전환시키고자 수행하였다. 식물세포에서 발현될 수 있는 promoter(35S-35S-AMV)에 내병성유전자인 DR-49 gene을 부착한 후 다시 식물형질전환용 binary vector에 도입하여 인삼에 도입되어 발현될 수 있도록 재조합하였으며, Disarmed Ti-plasmid 함유 Agrobacterium에 내병성유전자인 chitinase(pCH18)와 disease resistant gene(pDR)가 도입되었다. 인삼 callus 배양 과정을 거치지 않고 바로 multi-shoots를 생산하여 형질전환체 획득에 사용하고자 인삼 embryo와 petiole를 이용하여 direct shoots 생산을 유도한 결과 2,4-D 1 mg/ι와 kinetin 0.5 mg/ι 복합처리구에서 multi-shoot가 형성되었다. 또한 인삼 자엽을 이용한 형질전환에서도 MS 기본배지에 2,4-D 1 mg/ι와 kinetin 0.5 mg/ι를 첨가한 복합처리구에서 가장 효과적이었으며, dieases resistant와 chitinase 유전자에 의한 형질전환율은 각각 14%,그리고 18%를 나타내었다. 자엽으로부터 유기된 형질전환된 조직은 pre-embryoid 상태이기 때문에 성숙배의 과정을 거쳐 정상적인 shoot의 형성이 필요하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.235-243
• /
• 2002

Ni-base superalloys are used extensively in industry, both in aeroengines and land based turbines. About 60% by weight of most modern gas turbine engine structural components are made of Ni-base superalloys. To satisfy practical demands, the efficiency of gas turbine engines has been steadily and systematically increased by design modifications to handle higher turbine inlet or firing temperatures. However, the increase in operating temperatures has lead to a decrease in the life of components and increase in costs of replacement. Moreover, around 80% of the large frame size industrial/utility gas turbines operating in the world today were installed in the mid-sixties to early seventies and are now 25 to 30 years old. Consequently, there are greater opportunities now to repair and refurbish the older models. Basically, there are two major factors influencing the weldability of the cast alloys: strain-age cracking and liquation cracking. Susceptibility to strain-age cracking is due to the total Ti plus AI content of the alloy; Liquation cracking is due either to the presence of low melting constituents or constitutional liquation of constituents. Though Rene 41 superalloy has 4.5wt.% total Ti and Al content and falls just below the safe limit proposed by Prager et al., controlled grain size and special heat treatments are needed to obtain crack-free welds. Varying heat treatments and filler materials were used in a laboratory study, then the actual welding of service parts was carried out to verity the possibility of crack-tree weld of components fabricated from Rene 41 superalloy. The microstructural observations indicated that there were two kinds of carbides in the FCC matrix. MC carbides were located along the grain boundaries, while M$_{23}$C$_{6}$ carbide was located both inter and intra granularly. Two kinds of filler materials, Rene 41 and Hastelloy X were used to gas tungsten arc weld a patch into the sheet metal, along with varying pre-weld heat treatments. The microstructure, hardness and tensile tests were determined. The service distressed parts were categorized into three classes: with large cracks, with medium cracks and with small or no visible cracks. No significant difference in microstructure among the specimens was observed. Specimens were cut from the corner and the straight edge of the patch repair, away from the corner. The only cracks present were found to be associated with inadequate surface preparation to remove oxidation. Guidelines for oxide removal and the welding procedures developed in the research enabled crack-free welds to be produced.d.

• Journal of Nutrition and Health
• /
• 제14권2호
• /
• pp.97-104
• /
• 1981

Bacillus natto 및 Bacillus subtilis균(菌)을 이용(利用)한 청국장메주 제조(製造)와 재래식방법(在來式方法)에 의(依)한 청국장메주 발효과정중(醱酵過程中)의 성분(成分)과 효소력(酵素力)을 비교검토(比較檢討)한 결과(結果)는 다음과 같다. 1) 발효초기(醱酵初期)의 품온(品溫)이 $50{\sim}55^{\circ}C$였으나 12시간후(時間後)에 B. natto와 B. subtilis구(區)는 $48{\sim}52^{\circ}C$였고 재래식구(在來式區)는 $40^{\circ}C$였다. 72시간경(時間頃)에는 $41{\sim}48^{\circ}C$로 시험구(試驗區)에 따라서 품온(品溫)의 저하(低下)가 심하였다. 2) ethyl alcohol과 환원당(還元糖)은 12시간경(時間頃)에 최대치(最大値)을 나타핀후에 감소(減少)하는 경향이었으며 시험구간(試驗區間)외 차이(差異)는 거이 없었다. 3) pH는 시험구(試驗區) 모두 발효(醱酵) 12시간(時間)까지는 6.0이던 것이 72시간경(時間頃)에는 8.2이상(以上)으로 나타났고 적정산도(滴定酸度)는 발효초기(醱酵初期)에 최대치(最大値)를 나타였다. 4) 아미노실소(室素)와 수용성실소함량(水溶性室素含量)은 결시적(經時的)으로 증가(增加)하는 경향(傾向)으로서 B. natto구(區), 재래식구(在來式區), B. subtilis구(區)의 순(順)으로 높았다. 5) Amylase와 protease의 활성(活性)은 경시적(經時的)으로 불규칙적(不規則的)인 변화(變化)를 보였고 시험구간(試驗區間)의 차이(差異)가 없었으나 효소활성(酵素活性)은 대체(大體)로 미약(微弱)하였다. 본(本) 실험(實驗)에저 B.natto구(區)가 청국장매주 제조(製造) 균주(菌株)로서 성분(成分)과 관능면(官能面)에서 우수(優秀)하였다.0일이었다.환경적응성이 낮은 경향이었다.은 모두 경운 유 ㆍ무에 관계없이 시비수준이 높을수록 높은 경향을 보였고, 10일에 최고수준을 보인 후 완만한 감소를 나타냈으며, $K^{+}$, $Ca^{2+}$에 비해 $Mg^{2+}$이 보다 낮은 함량을 보였다.989년산 일반계를 10분도와 12분도로 도정하였을 때 도정도에 따른 밥맛의 차이는 없었다.X>$CoO_x$는 $Co_3O_4$로 존재하고, 반응 전의 경우에는 이와는 다른 chemical state를 보여주었다. XRD 및 XPS 결과를 바탕으로, 촉매표면에 존재하는 $Co_3O_4$의 외부표면이 $Co_2TiO_4$와 $CoTiO_3$ 같은 $CoTiO_x$로 encapsulation되어 있는 모델구조를 제안할 수 있고, 이는 반응시간의 함수로 나타나는 촉매활성에 있어서 전이영역의 존재를 잘 설명할 수 있을 뿐만 아니라, XRD와 XPS에서 얻어진 촉매의 물리화학적인 특성을 잘 반영할 수 있다. 나타냈고, 골격근과 눈 조직에서 피루브산에 대한 LDH의 친화력이 상당히 크므로 LDH가 혐기적 조건에서 효율적으로 기능을 하는 것으로 사료된다.5) and "Cleanliness of clothes ＆ features" (p ＜0.05) of VIP ward were significantly higher than those of a general ward.tive to apply.아울러 고려(考慮)해야 한다. 이것은 고무기술자(技術者)가 당면(當面)해야할 과제(課題)에 속(屬)하며 바람직 한것은 본장(本章)의 내용(內容)이 여러 상황하(狀況下)에서 당면(當面)한 문제(問題)에 대(對)해 어떻게 대처(對處)해 야 할지를 모르는 여러 기술자(技術者)들에게

• 한국전기전자재료학회논문지
• /
• 제17권1호
• /
• pp.7-15
• /
• 2004

The ferroelectric SBT thin films as a material of capacitors for non-volatile FRAMs have some problems that its remanent polarization value is relatively low and the crystallization temperature is quite high abovc 80$0^{\circ}C$. Therefore, in this paper, SBTN solution with S $r_{0.9}$B $i_{2.1}$T $a_{1.8}$N $b_{0.2}$$O_{9}$ composition was synthesized by sol-gel method. Sr(O $C_2$ $H_{5}$)$_2$, Bi(TMHD)$_3$, Ta(O $C_2$ $H_{5}$)$_{5}$and Nb(O $C_2$ $H_{5}$)$_{5}$ were used as precursors, which were dissolved in 2-methoxyethanol. SBTN thin films with 200 nm thickness were deposited on Pt/Ti $O_2$/ $SiO_2$/Si substrates by spin-coating. UV-irradiation in a power of 200 W for 10 min and rapid thermal annealing in a 5-Torr-oxygen ambient at 76$0^{\circ}C$ for 60 sec were used to promote crystallization. The films were well crystallized and fine-grained after annealing at $650^{\circ}C$ in oxygen ambient. The electrical characteristics of 2Pr=11.94 $\mu$C/$\textrm{cm}^2$, Ps＋/Pr＋=0.54 at the applied voltage of 5 V were obtained for a 200-nm-thick SBTN films. This results show that 2Pr values of the UV irradiated and rapid thermal annealed SBTN thin films at the applied voltage of 5 V were about 57% higher than those of no additional processed SBTN thin films. thin films.lms.s.s.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.82.1-82.1
• /
• 2012

란타늄 산화물 ($La_2O_3$) 박막은 하프늄 산화물 ($HfO_2$) 박막보다 높은 유전 상수와 높은 밴드 오프셋으로 인해 dynamic random access memory(DRAM)에서 유전체 재료로써 연구되어 왔다. 그리고 Lanthanum이 도핑된 HfO2이 더 높은 유전 상수와 낮은 누설 전류 밀도를 갖는 다는 사실이 이전에 보고 된 바 있다. 본 연구에서 우리는 ALD를 이용하여, TiN 하부 전극 위에 $La_2O_3$의 위치를 달리하는 $La_2O_3/HfO_2$의 나노 층상조직 구조(두께 10 nm)를 금속 - 절연체 - 금속 (MIM) 구조로 제작 하였다. ALD는 좋은 comformality와 넓은 지역 균일성을 가지며, 원자수준의 두께를 조절할 수 있다는 장점을 갖고 있다. 또한, 다양한 화학 물질들을 이용한 복합적 계층구조를 만들 수 있는 점과 $HfO_2$ 및 $La_2O_3$ 계층의 수직 위치를 정확하게 조절할 수 있는 점으로 본 연구에 적합한 증착 방법이다. HfO2 속에 $La_2O_3$ 층을 깊이에 따라 삽입함으로써 $HfO_2$ 계층에 La 도핑의 효과와 더불어 TiN 하부 전극 위의 $La_2O_3$과 $HfO_2$의 차이점을 확인 하였다. $HfO_2$은 $250^{\circ}C$에서 TDMAH와 물을 사용하여, $La_2O_3$은 동일한 온도에서 $La(iPrCp)_3$와 물을 사용하여 제작되었다. 화학적 구성 및 binding 구조는 X선 광전자 분광법 (XPS)을 통해 분석하였다. 전기적 특성(유전 상수 및 누설 전류)은 Capacitance-Voltage (CV)와 Current-Voltage (IV) 측정으로 확인하였다. 결과적으로, $La_2O_3$ 또는 $HfO_2$을 한 종류만 사용한 절연층의 전기적 특성보다, $La_2O_3/HfO_2$의 나노 층상조직 구조가 더 나은 특성 (누설 전류 밀도 : $5.5{\times}10^{-7}\;A/cm^2$ @-1MV/cm, EOT : 14.6)을 갖는다는 것을 확인했고, 더불어 $La_2O_3$의 흡습 성질로 인한 화학 구조와 전기적 특성의 일부 차이를 확인하였다. 본 연구에서는 $HfO_2$ 속에 $La_2O_3$층이 TiN 하부 전극 바로 위에 위치할 때, 즉, 공기 중에 노출되지 않은 $La_2O_3/HfO_2$ 구조에서 가장 좋은 특성의 MIM capacitor를 얻을 수 있었다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제22권7호
• /
• pp.937-942
• /
• 2009

The aim of this study was to analyze the effects on growth and muscle development during the growing period of the sex-linked dwarf gene in the background of a Taiwan Country chicken strain, L2, selected for egg production. Eight crossbred males, heterozygous for the DW*DW mutation, were each backcrossed to six females of the L2 strain to produce two genotypes of BC females, either normal (DW*N+/-) or dwarf (DW*DW/-). The experiment included 251 normal and 207 dwarf pullets. The effect of the dwarf gene on body weight and shank length was highly significant from 2 weeks of age. The reduction of body weight by the dwarf gene reached 34.8% and 37.4% as compared to normal sibs at 16 and 20 weeks of age, respectively. Parameters of the growth curve were estimated: the age at inflection (TI) was higher in normal pullets (66.9 days) than in dwarf pullets (61.2 days). A significant effect of the dwarf gene on single muscle fiber cross-section area was found from 12 weeks of age onwards, whereas the dwarf gene had no effect on the total number of muscle fibers. Comparing the effect of the dwarf gene on shank length at different ages revealed an earlier effect on skeleton growth, observed from 2 weeks of age, than on muscle development, which was affected from 8 to 12 weeks of age.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제52권10호
• /
• pp.458-463
• /
• 2003

In order to develope piezoelectric transformer for the ballast of fluorescent lamp, a new shape and electrode pattern of piezoelectric transformer has been investigated in this work. The composition of piezoelectric ceramics was 0.95Pb(Zr$_{0.51}$Ti$_{0.49}$)O$_3$+0.03Pb(Mn$_{1}$3/Nb$_{2}$3/)O$_3$+0.02Pb(Sb$_{1}$2/Nb$_{1}$2/)O$_3$. The sample prepared by this composition system showed the characteristics which has about 1200 of relative dielecric constant, 1100 of the mechanical quality factor, 0.53 of the electromechanical coupling coefficient, 320 pC/N of the piezoelectric constant d$_{33}$, 0.3 % of the dissipation factor. Diameter and thickness of disk-type piezoelectric transformer was 45 mm and 4 mm, respectively. The driving and generating electrode with their gap of 1mm were fabricated on the top surface. But the common electrode was fabricated on the whole bottom surface. The electrode surface ratio of driving and generating part on the top surface ranges from 1.4:1 to 3:1. We investigated the electrical characteristics with the variation of the electrode surface ratio of driving and generating part in the range of load resistance of 100 $\Omega$～70 k$\Omega$. The set-up voltage ratio of this piezoelectric transformer increases with increasing both the electrode surface of driving part and the load resistance. The set-up voltage ratio at no load resistance was more than 60 times. On the other hand, the efficiency decreases with increasing the electrode surface of driving part. In the case of the electrode surface of both 1.4:1 and 2:1, maximum efficiency showed above 97 % at load resistance of 2 k$\Omega$. However, in the case of the electrode surface of 3:1, maximum efficiency showed about 94 % at load resistance of 3 k$\Omega$.>.>.>.