• Journal of the Korea Institute of Military Science and Technology
• /
• v.7 no.2 s.17
• /
• pp.81-87
• /
• 2004

Semiconductor thick film gas sensors based on tin oxide are fabricated and their gas response characteristics are examined for four simulant gases of chemical warfare agent (CWA)s. The sensing materials are prepared in three different sets. 1) The Pt or Pd $(1,\;2,\;3\;wt.\%)$ as catalyst is impregnated in the base material of $SnO_2$ by impregnation method.2) $Al_2O_3\;(0,\;4,\;12,\;20\;wt.\%),\;In_2O_3\;(1,\;2,\;3\;wt.\%),\;WO_3\;(1,\;2,\;3\;wt.\%),\;TiO_2\;(3,\;5,\;10\;wt.\%)$ or $SiO_2\;(3,\;5,\;10\;wt.\%)$ is added to $SnO_2$ by physical ball milling process. 3) ZnO $(1,\;2,\;3,\;4,\;5\;wt.\%)$ or $ZrO_2\;(1,\;3,\;5\;wt.\%)$ is added to $SnO_2$ by co-precipitation method. Surface morphology, particle size, and specific surface area of fabricated sensing films are performed by the SEM, XRD and BET respectively. Response characteristics are examined for simulant gases with temperature in the range 200 to $400^{\circ}C$, with different gas concentrations. These sensors have high sensitivities more than $50\%$ at 500ppb concentration for test gases and also have shown good repetition tests. Four sensing materials are selected with good sensitivity and stability and are fabricated as a sensor array A sensor array Identities among the four simulant gases through the principal component analysis (PCA). High sensitivity is acquired by using the semiconductor thick film gas sensors and four CWA gases are classified by using a sensor array through PCA.

• Nuclear Engineering and Technology
• /
• v.45 no.7
• /
• pp.847-858
• /
• 2013

Since 2001, a series of five irradiation test campaigns for atomized U-Mo dispersion fuel rods, KOMO-1, -2, -3, -4, and -5, has been conducted at HANARO (Korea) in order to develop high performance low enriched uranium dispersion fuel for research reactors. The KOMO irradiation tests provided valuable information on the irradiation behavior of U-Mo fuel that results from the distinct fuel design and irradiation conditions of the rod fuel for HANARO. Full size U-Mo dispersion fuel rods of 4-5 $g-U/cm^3$ were irradiated at a maximum linear power of approximately 105 kW/m up to 85% of the initial U-235 depletion burnup without breakaway swelling or fuel cladding failure. Electron probe microanalyses of the irradiated samples showed localized distribution of the silicon that was added in the matrix during fuel fabrication and confirmed its beneficial effect on interaction layer growth during irradiation. The modifications of U-Mo fuel particles by the addition of a ternary alloying element (Ti or Zr), additional protective coatings (silicide or nitride), and the use of larger fuel particles resulted in significantly reduced interaction layers between fuel particles and Al.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1574-1576
• /
• 2003

Carbon nanotubes (CNTs) were grown on the TiN-coated silicon substrate with different thickness of Ni and Co catalysts layer at $600^{\circ}C$ using inductively coupled plasma-chemical vapor deposition (ICP-CVD). The Ni and Co catalysts were formed using the RF magnetron sputtering system with various deposition times. It was found that the growth of CNTs was strongly influenced by the surface morphology of Ni and Co catalysts. With increasing deposition time, the thickness of catalysts increased and the grain boundary size of catalysts increased. The surface morphology of catalysts and CNTs were elucidated by SEM. The Raman spectrum further confirmed the graphitic structure of the CNTs. The turn-on field of CNTs grown on Ni and Co catalysts was about 2.7V/pm and 1.9V/pm respectively. Field emission current density of CNTs grown on Ni and Co catalysts was measured as $11.67mA/cm^2$ at $5.5V/{\mu}m$ and $1.5mA/cm^2$ at $5.5V/{\mu}m$ respectively.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1938-1940
• /
• 2003

본 연구는 요소 센서 제작을 위한 과정으로서, 전기화학적 방법을 이용한 다공질 실리콘 구조 형성과, PDV(Physical Vapor Deposition) 법에 의한 백금 박막 코팅 및 전기화학적 전도성 고분자 코팅과 urease 고정화 단계를 고찰하고 감도 특성을 제시 하였다. 전극 기질로서 B을 도우핑한 p-type 실리콘웨이퍼를 사용하였고, HF:$C_2H_5OH:H_2O$=1:2:1의 부피비를 갖는 에칭 용액에서 5분간 -7 $mA/cm^2$의 일정 전류를 가하여 폭 2 ${\mu}m$, 깊이 10 ${\mu}m$의 다공질 실리콘(PS) 충을 형성하였다. 그 위에 200 ${\AA}$의 Ti 층을 underlayer로서 증착하고, 2000 ${\AA}$의 Pt를 중착하여 PS/Pt 박막 전극을 제작하고, 전도성 고분자로서 polypyrrole (PPy), 또는 poly(3-mehylthiophene) (P3MT)을 전기화학적으로 코팅한 후, urease(EC 3.5.1.5, type III, Jack Bean, Sigma)를 고정화 하였다. 고정화 시 전해질 수용액의 pH는 7.4로 하여 urease표면이 음전하를 갖도록 하고, 전극에 0.6 V (vs. SCE(Saturated Calomel Electrode))의 일정 전압을 가함으로써 urease가 전도성 고분자 표면에 전기적으로 흡착되도록 하였다. 이상의 방법으로 제작한 요소 센서의 감도는 PPy와 P3MT를 전자 전달 매질로 사용한 경우, 각각 8.44 ${\mu}A/mM{\cdot}cm^2$와 1.55 ${\mu}A/mM{\cdot}cm^2$의 감도를 보였다.

• The Korean Journal of Physiology and Pharmacology
• /
• v.13 no.2
• /
• pp.71-78
• /
• 2009

(S)-Carbamic acid 2-[4-(4-fluoro-benzoyl)-piperidin-1-yl]-1-phenyl-ethyl ester hydrochloride (YKP1447) is a novel "atypical" antipsychotic drug which selectively binds to serotonin (5-$HT_{2A}$, Ki=0.61 nM, 5-$HT_{2C}$, Ki=20.7 nM) and dopamine ($D_2$, Ki=45.9 nM, $D_3$, Ki=42.1 nM) receptors with over $10\sim100$-fold selectivity over the various receptors which exist in the brain. In the behavioral studies using mice, YKP1447 antagonized the apomorphine-induced cage climbing ($ED_{50}$=0.93 mg/kg) and DOI-induced head twitch ($ED_{50}$=0.18 mg/kg) behavior. In the dextroamphetamine-induced hyperactivity and conditioned avoidance response (CAR) paradigm in rats, YKP1447 inhibited the hyperactivity induced by amphetamine ($ED_{50}$=0.54 mg/kg) and the avoidance response ($ED_{50}$=0.48 mg/kg); however, unlike other antipsychotic drugs, catalepsy was observed only at much higher dose ($ED_{50}$=68.6 mg/kg). Based on the CAR and catalepsy results, the therapeutic index (TI) value for YKP1447 is over 100 (i.p.). These results indicate that YKP1447 has an atypical profile and less undesirable side effects than currently available drugs.

• Restorative Dentistry and Endodontics
• /
• v.39 no.4
• /
• pp.270-275
• /
• 2014

Objectives: This study compared the mechanical properties of various instruments for canal exploration and glide-path preparations. Materials and Methods: The buckling resistance, bending stiffness, ultimate torsional strength, and fracture angle under torsional load were compared for C+ file (CP, Dentsply Maillefer), M access K-file (MA, Dentsply Maillefer), Mani K-file (MN, Mani), and NiTiFlex K-file (NT, Dentsply Maillefer). The files of ISO size #15 and a shaft length of 25 mm were selected. For measuring buckling resistance (n = 10), the files were loaded in the axial direction of the shaft, and the maximum load was measured during the files' deflection. The files (n = 10) were fixed at 3 mm from the tip and then bent $45^{\circ}$ with respect to their long axis, while the bending force was recorded by a load cell. For measuring the torsional properties, the files (n = 10) were also fixed at 3 mm, and clockwise rotations (2 rpm) were applied to the files in a straight state. The torsional load and the distortion angle were recorded until the files succumbed to the torque. Results: The CP was shown to require the highest load to buckle and bend the files, and the NT showed the least. While MA and MN showed similar buckling resistances, MN showed higher bending stiffness than MA. The NT had the lowest bending stiffness and ultimate torsional strength (p < 0.05). Conclusions: The tested instruments showed different mechanical properties depending on the evaluated parameters. CP and NT files were revealed to be the stiffest and the most flexible instruments, respectively.

• Applied Chemistry for Engineering
• /
• v.8 no.3
• /
• pp.438-445
• /
• 1997

${\beta}-PbO_2$ electrode, which was electrodeposited on Ti madras, was prepared and for the decomposition of cyanide in electroplating wastewater. After the investigation of temperature and pH conditions for no hydrogen cyanide evolution during the decomposition of cyanide, the optimum current densities of ${\beta}-PbO_2$ electrodeposition and cyanide decomposition were determined in 500ppm NaCN solution, and durability of ${\beta}-PbO_2$ electrode was also investigated. Hydrogen cyanide was actively generated above $40^{\circ}C$ and was not evolved above pH 13. ${\beta}-PbO_2$ electrode electodeposited at $5A/dm^2$ showed the best cyanide decomposition efficiency The decompostion efficiency was about 70% at low decomposition current density ($0.08A/dm^2$), and it decreased gradually to about 10% as the decomposition current density increased up to $4A/dm^2$. The film of ${\beta}-PbO_2$ electrodeposited was corrosive at $20A/dm^2$ and was broken at $50A/dm^2$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.137-137
• /
• 2009

Thin-film transistors (TFTs) that can be prepared at low temperatures have attracted much attention due to the great potential for flexible electronics. One of the mainstreams in this field is the use of organic semiconductors such as pentacene. But device performance of the organic TFTs is still limited by low field effect mobility or rapidly degraded after exposing to air in many cases. Another approach is amorphous oxide semiconductors. Amorphous oxide semiconductors (AOSs) have exactly attracted considerable attention because AOSs were fabricated at room temperature and used lots of application such as flexible display, electronic paper, large solar cells. Among the various AOSs, a-IGZO was considerable material because it has high mobility and uniform surface and good transparent. The high mobility is attributed to the result of the overlap of spherical s-orbital of the heavy pest-transition metal cations. This study is demonstrated the effect of thickness channel layer from 30nm to 200nm. when the thickness was increased, turn on voltage and subthreshold swing were decreased. a-IGZO TFTs have used a shadow mask to deposit channel and source/drain(S/D). a-IGZO were deposited on SiO2 wafer by rf magnetron sputtering. using power is 150W, working pressure is 3m Torr, and an O2/Ar(2/28 SCCM) atmosphere at room temperature. The electrodes were formed with Electron-beam evaporated Ti(30nm) and Au(70nm) structure. Finally, Al(150nm) as a gate metal was evaporated. TFT devices were heat treated in a furnace at $250^{\circ}C$ in nitrogen atmosphere for an hour. The electrical properties of the TFTs were measured using a probe-station to measure I-V characteristic. TFT whose thickness was 150nm exhibits a good subthreshold swing(S) of 0.72 V/decade and high on-off ratio of 1E+08. Field effect mobility, saturation effect mobility, and threshold voltage were evaluated 7.2, 5.8, 8V respectively.

• Journal of the Mineralogical Society of Korea
• /
• v.6 no.1
• /
• pp.1-16
• /
• 1993

The chemical and optical absorption spectroscopic characters of pink and colorless tourmalines from San Diego mine in California, U.S.A., blue/green tourmalines from anonymous mine, Brazil, and brownis black tourmalines from Uncheon and Haksan mines in Korea have been studied using X-ray diffractometer, electron microprobe, optical absorption spectroscopy, and heat treatment. Least-squares refinements give unit cell diminsions : a = 15.96-16.01 ${\AA}$, c = 7.15-7.16 ${\AA}$ for the brownish black tourmalines, a = 15.82 - 15.87 ${\AA}$, c = 7.09 - 7.10 ${\AA}$ for pink tourmalines, and a = 15.88 - 15.94 ${\AA}$, c = 7.12 - 7.15 ${\AA}$ for blue green tourmalines. The colors of tourmalines are responsible for the transition elements. The pink color is attributed to the $Mn^{3+}$ ions, the blue-green to $Fe^{2+}$ and $Mn^{2+}$, bluish green to $Cu^{2+}$, and the brownish black to $Fe^{2+}$, $Fe^{2+}$ - $Fe^{3+}$, and $Fe^{2+}$ - $Ti^{4+}$. The $Mn^{3+}$ ions of pink color tourmalines are stabilized in the Y sites compressed along the O(1)H-O(3)H axis by Jahn-Teller distortion. Heating removes the pink or red component from tourmalines, producing the colorless stones from the pink and red ones. The bluish green samples change into the greenish blue ones and a certain yellowish green samples change into the light green ones by heat treatment. In the elbaite-schorl series, the concentration of Fe and Mn are variable depending on the color zones. The green zone is characterrized by the high content of Fe and Mn are variable depending on the color zones. The green zone is characterized by the high content of Fe, whereas the pink zone by the high content of Mn. Mn increases in deep yellow zone compared with yellow or colorless zones.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.40 no.4
• /
• pp.494-503
• /
• 1995

The selection of salt tolerant rice variety needs an effective method in its testing. Salinity of irrigated water, 0.5% at seedling stage, 0.6% at tillering stage, and 0.9% at panicle formation stage were treated to test salt tolerance of rice using 45 cultivars. At tillering stage, salty water irrigation reduced plant height to 22.6% in early maturing rices(EMR), 30.5% in medium maturing rices(MMR), and 20.9% in medium-late maturing rices(MLMR), and also reduced number of tillers to 11.2% in EMR, 36.2% in MMR, and 36.0% in MLMR compared to rices grown in non-salty water irrigation. At panicle formation stage of rice, salty water irrigation affected plant height and tiller numbers that showed varietal differences. As salt tolerant rice cultivars, Daegwangbyeo, Namweonbyeo, Sinseonchalbyeo, Gyehwabyeo, and Daeyabyeo were selected. Jinbubyeo, Donghaebyeo, and Tamjinbyeo were weak in salty water irrigation.