• 정보저장시스템학회:학술대회논문집
• /
• 2005.10a
• /
• pp.179-183
• /
• 2005

Particles in the HDD can cause serious damages such as scratches and thermal asperity(TA) at the head/disk interface(HDI). Accordingly, particles cause data loss including physical and electrical damages. To improve the reliability of head-disk interface, understanding the damage characteristics at the HDI due to particle interactions is required. The materials such as $A1_2O_3$, TiC and aluminum were used in this experiment. The size and hardness of particles injected into the HDI are closely relevant to surface damage caused the data loss on the disk and head. In this paper, a variety of scratches were analyzed using scanning electron microscope(SEM) and atomic force microscope(AFM). In order to analyze defects of very small size on the disk, optical surface analyzer(OSA) was also used.

• Proceedings of the KIEE Conference
• /
• 1997.07d
• /
• pp.1537-1539
• /
• 1997

In this study, the dielectric properties of $Pb(Mg_{1/3}Nb_{2/3})O_3-PbTiO_3$ Ceramics have been investigated as a addition of the amount of $MnO_2(0{\leq}x{\leq}0.9wt%)$. The Temperature-dependant dielectric characteristics of 0.9PMN-0.1PT relaxor ferroelectric system were improved by enhencing the extent of the diffuse phase transition(DPT). The maximum dielectric permittivity decreased by substitution $MnO_2$ and the dielectric loss decreased with increasing $MnO_2$ substitution amount. It is expected decreasing in inner heat energy for temperature with increasing $MnO_2$ substitution.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.10a
• /
• pp.143-145
• /
• 2007

The correlation between crystallization and deformation behavior in the supercooled liquid region (SLR) of a $Cu_{54}Ni_{6}Zr_{22}Ti_{18}$ bulk metallic glass (BMG) alloy is investigated by compression tests, differential scanning calorimetry (DSC), electron energy loss spectrometry (EELS) and high resolution transmission electron microscopy (HRTEM). In the SLR, This BMG alloy was strongly depended on the deformation temperature and the alloy exhibits important change in deformation behavior after a given time which is directly connected to the development of crystallization. Compressive stress impeded decomposition and consequently retarded forming of nano-crystal, which led to enlarge the homogeneous deformation region of the BMG alloy in SLR during compression test.

• Journal of Korea Foundry Society
• /
• v.14 no.1
• /
• pp.62-74
• /
• 1994

The concentration and particle size distribution of non-metallic inclusions which suspended in the molten aluminum at $700^{\circ}C$ were measured by using LiMCA apparatus. The result revealed that the number of inclusions increased with increasing the applied current or decreasing the orifice diameter, while decreased with increasing the purity of aluminum. And also, it was found that the number of inclusions increased with increasing the amount of boron added to molten aluminum. This was found to be attributed to the formation of the inclusions of TiB and $V_3B_2$. It was investigated that the average concentration of inclusions in a constant volume of 20ml of molten aluminum was increased in the order of pure molten aluminum, molten aluminum containing 20ppm of boron and molten aluminum used repeatly in the experimental casting in this study.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.5 no.7
• /
• pp.59-62
• /
• 1982

The purpose of this paper is to increase the effectiveness of decreasing time - load and cost down in manufacturing company using the new way of regulating standard time - load. Let us take an example of K automobile factory. This company have avoided the used to way of regulating standard ti me load in staff members and increased the effectiveness of decreasing time - load having participated all members centering around the Q.C circle. Here, We can take conclusions as below. 1. We could improve the consciousness of question and the consciousness of efficiency progress as a result of new way. 2. We could encourage the activation of organization and working desire of all members to be participated.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.2 no.1
• /
• pp.67-75
• /
• 1996

An innovative batch electrolytic system consisted of electrolytic basin, which was equipped with DSA(Dimensionally Stable Anode) type insoluble electrode, Ti/IrO2 anode and H-C metal cathode, and flotation separator was developed for the efficient treatment of shipboard emulsified oily wastewater. The electorod cleance and current density of elecrolytic basin to ensure maximum treatment efficiency of oily wastewater was evaluated as 6 mm, 3 A/dm3, respectively. The electrolytic efficiency of oily wastewater was affected by the operationtemperature, and it means that the temperature controller to ensure the stabiity of the process is required. The conductivity in the electrolytic basin was increased with the percentage of sea water in the oily wastewater, and over 90% of treatment efficiency of oily wastewater could be obtained at 7% of sea water. The oil removal rate was increased according to the increase of the quantity of electricity, and the maximum value of electrilyic rate constant was 288 mgoil/A.min. The information obtained from this study might be used for development of an efficient continuous electrolytic system treating the emulsified oily wastewater.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.263-266
• /
• 2000

Effects of excess Pb(50 mole ％) on the crystallization properties of amorphous PZT thin films on the glass substrates by post-annealing in oxygen ambient were investigated to lower the crystallization temperature of the PZT thin films with a single perovskite phase. The PZT thin films(350nm) were prepared on Pt/Ti/corning glass(1737) substrates. The PZT thin films and bottom electrode were deposited by RF magnetron sputtering. Crystallization properties of PZT thin films were strongly dependent on RTA(Rapid Thermal Annealing) temperature. We were able to obtain a perovskite structure of PZT at 600$^{\circ}C$ for 10min. After thermal treatments were done, electrical properties such as I-V, P-E, and fatigue were measured.

• International journal of advanced smart convergence
• /
• v.10 no.1
• /
• pp.89-96
• /
• 2021

The goal of this study is to develop experiment monitoring system of agriculture fields using ZigBee wireless modules. Soil moisture, ambient temperature, atmospheric pressure and intensity of sunlight are the most important factorsto grow a wheat crop and other vegetables. In orderto monitorthe factorssoil moisture (YL69), air pressure (BMP180), temperature (DS18B20), photoresistor were used for sensing environment data. The TI CC2530 RF SoC chip was used in the system. ZigBee modules were connected to star topology. ZigBee modules send data wirelessly to a data center. This data can be displayed and analyzed on the main monitoring program as needed also sent to the client mobile. Characteristics of the sensors were determined by experiment results.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.03a
• /
• pp.34-34
• /
• 2003

Piezoelectric or magnetostrictive materials, known as smart materials, have been researched widely for sensors or actuators in micro system technology. In our research, thick sol-gel lead zirconate titanate(Pb(Zr$\sub$1-x/Ti$\sub$x/)O$_3$) films were fabricated and their characteristics were investigated f3r angular rate sensor applications. The thickness of the PZT films is 1.5${\mu}$m, which is required by a vibration angular rate sensor for a good actuation and sensing. The remnant polarization of the PZT flms is 12.0 ${\mu}$C/$\textrm{cm}^2$. The electromechanical constants of PZT thin film showed the value of susceptance(B) of 4800${\mu}$ s at capacitance of 790pF. The PZT films were applied to the vibration angular rate sensor structure and the vibration of 1.78 ${\mu}$m in amplitude at the resonant frequency of 35.8㎑ was obtained by driving voltage of 5V$\sub$p-p/ of bulk piezoelectric materials with out of phase signal through voltage and inverting amplifier.

• Journal of the Korean Ceramic Society
• /
• v.49 no.5
• /
• pp.432-437
• /
• 2012

Electrical properties of the laminated SMD-type PTC thermistor for microcircuit protection were investigated as a function of calcination and sintering temperature. $BaTiO_3$ with $Y_2O_3$ and $MnO_2$ were calcined at 1000 to $1150^{\circ}C$ for 2h and the laminated SMD-type PTC thermistor was sintered at 1350 to $1400^{\circ}C$ for 2h in a reduced atmosphere (1% $H_2/N_2$). Sintered density of the sample was dependent on the calcination and sintering temperature. Electrical properties of the sintered samples were strongly dependent on the densities of samples. For the samples with density below 4.6 g/$cm^3$, the insulator characteristics were observed, while PTC jump characteristics (R150/R30) were disappeared for the sample with density above 5.05 g/$m^3$. Optimal PTC characteristics were obtained for the sintered samples with density of 5.05 g/$m^3$. The laminated SMD-type PTC thermistor prepared by calcination at $1100^{\circ}C$ for 2h and sintering at $1270^{\circ}C$ for 2h showed the room temperature resistivity of $11{\Omega}{\cdot}cm$ and PTC jump characteristics of $10^2$ order.