• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1129-1132
• /
• 1995

In the preparation of the layered $BaTiO_3$ thin films with high performance, the new stacking method using the continuous cooling of the substrate was introduced. Amorphous/polycrystalline $BaTiO_3$ layered structure was confirmed by SEM and index of refraction. The layered $BaTiO_3$ thin films formed by the new stacking method showed such a high dielectric constant that the layered structure could not be explained by a stacking structure of the two defined layers but could only be explained by multi-layered structure, i.e. amorphous/micro crystalline/polycrystalline structure. The layered $BaTiO_3$ thin film with a thickness of 240 nm showed higher capacitance per unit area and breakdown strength than the double layered $BaTiO_3$ thin film prepared by the conventional stacking method. And well defined ferroelectric hysteresis leer was observed in the layered $BaTiO_3$ thin film with a thickness of 200 nm.

• 한국세라믹학회지
• /
• 제34권7호
• /
• pp.758-766
• /
• 1997

Non-brittle fracture behaviour of the two composite structures made of two different brittle materials was investigated using 3-point bending test. First, the layered and fibrous macro-composites were fabricated using the material easily formed, yet showing a brittle fracture behaviour similar to ceramics. The layered and fibrous Al2O3 /Al2O3 composites with weak interface were also fabricated using plate of 2 mm thickness and rod of 3 mm diameter respectively. Comparison of the mechanical properties between these two structures was performed in the lights of flexural strength and work of fracture for the composites consisting of Al2O3 and simulated materials respectively. The strength ratio of layered structure to the monolith of same volume was 0.6 and the ratio of fibrous one was about 0.2 for the composites made of simulated brittle material. The ratio of the work of fracture of the fibrous to the layered was 0.47. For Al2O3/Al2O3 composites, the strength ratio of layered and fibrous structures to the monolith with same volume were about 0.6 and 0.2 respectively. The ratio of work of fracture of the fibrous to the layered was 0.6. These confirmed that the layered structure was superior to the fibrous one in terms of flexural strength and work of fracture.

• 한국통신학회논문지
• /
• 제21권7호
• /
• pp.1850-1860
• /
• 1996

We present the results for the design ofantireflection (AR) coatings on facets of a multilayered structure waveguide device. The method, whose results agree very well with the reusults of the rigorous method in the case of a symmetric three layer structure deveice, is extended for the design of AR coatings on the facets of a multilayered structure waveguide device. the field profile in a multilayered structure waveguide necessary for the use of the extended method is obtained from the transfer matrix method. The virtual four layered structure method (VFLM) is proposed to reduce the time for the design ofAR coatings because the time for the design of AR coatings using the extended method increases as the number of layers increases. The optimum coating parameters and tolerance mapsfor two different six layered waveguide devices in Ref. [9] and [10] are obtained using the extendedmethod and the VFLM,and for the three different cases approximated as three layered waveguide devices to compare the results of each case. The results of the VFLM are similar to those of the extended methodcompared to those of the three layered structure waveguide. The main reason for the above results is that the field profile in the device calculated usingthe VFLM is similar to that calculated using the extended method compared to that for three layered structure wavegjide. We conclude that the extended method or VFLM should be used for the design of AR coatings on facets of a deice required for the facet reflectivity less than 10$^{-3}$ such as a semiconductor otical amplifier.

• 한국소음진동공학회논문집
• /
• 제26권4호
• /
• pp.375-382
• /
• 2016

The mechanical property of a carbon-fiber-reinforced plastic (CFRP) is subjected to two elements, carbon fiber and polymer resin, in a first step and the selection of multi-layered structure is second one. Many combination of fabric layers, i.e. plainweave, twillweave, can be derived for candidates of test specimen used for a basic mechanical components so that a reliable identification of dynamic nature of possible multi-layered structures are essential during the development of CFRP based component system. In this paper, three kinds of multi-layered structure specimens were prepared and the dynamic characteristics of service specimens were conducted through classical modal test process with impact hammer. In addition, the design sensitivity analysis based on transmissibility function was applied for the measured response data so that the response sensitivity for each resonance frequency were compared for three CFRP test specimens. Finally, the evaluation of CFRP specimen over different multi-layered fabric structures are commented from the experimental consequences.

• ETRI Journal
• /
• 제25권6호
• /
• pp.517-522
• /
• 2003

This investigation confirms that silver stearate consists of an infinite-sheet, two-dimensional, nonmolecular layered structure. Scanning electron microscopy, X-ray diffraction, and infrared spectroscopy reveal the following: plate-like morphology is identified from the SEM image, XRD peaks can be indexed to the (0k0) reflections of a layered structure, and infrared peaks show that alkyl chains are present in an all-trans conformational state with little or no significant gauche population. Based on these structural characteristics, we demonstrate that silver stearate, a prototype of layered organic-inorganic hybrid material, can be grown not only in a designed two-dimensional pattern but also in three-dimensionally ordered ways by using carboxyl-group terminated nanoparticles as a template.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2015년도 추계 학술논문 발표대회
• /
• pp.107-108
• /
• 2015

Layered Double Hydroxides is known as a hydrotalcite-like material. It is a type of anionic clay with planar structure. It is composed of layer structure which is able to exchange anion between two layers which includes divalent ion and trivalent ion. Therefore, layered double hydroxide is applicable for eliminating harmful heavy metals and anionic substances which exist in the concrete. Because it is also able to be used as catalyst and has high possibility of utilization, It is getting an large amount of attention recently. In this study, an analysis on the structure of the layerd double hydroxide (LDH) which is possible to bind the anion was carried out.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.381-382
• /
• 2006

The mechanical behaviors of multi-layered foam core sandwich composite were investigated through a 3-point bending test. The sandwich specimens were obtained from sandwich panel consisting of aluminum faces and urethane foam core. Three types of sandwich specimens such as a single structure, a double structure and a triple structure were considered. The span of sandwich specimens were varied from 170mm to 350mm. According to the results, the flexural and shear properties of multi-layered sandwich composite were found to be higher than those of single-layered sandwich composite.

• 한국공간구조학회논문집
• /
• 제11권3호
• /
• pp.137-145
• /
• 2011

최근 건축 경향에 따라 단층 프리폼 구조에 대한 관심이 증대되고 있다. 축력과 모멘트를 동시에 받는 구조적인 특성으로 인해 프리폼 구조에서 노드는 응력이 집중되는 부분으로 상세 개발이 이루어져야 한다. 본 논문은 단층 프리폼 구조의 모멘트형 노드를 제안하고 축력과 모멘트에 대한 유한요소해석을 수행하였다. 유한요소해석을 통해 내력이 검증된 모델에 구멍 크기 및 위치에 따른 변수를 적용하여 변수해석을 진행하였고 결과를 비교분석하여, 구조적인 성능을 만족하여 안전성을 가지고 동시에 물량도 가장 절약할 수 있는 노드 Prototype을 결정하였다.

• 한국표면공학회지
• /
• 제33권1호
• /
• pp.25-33
• /
• 2000

The synthesis and characterization of intercalated compound of dodecanesulfornate into hydrated metal, [M($H_2$O)\ulcorner](C\ulcornerH\ulcorner$SO_3$)$_2$.$xH_2$O (M=Co, Cu) was presented. The compounds shows a layered structure which was determined by powder X-ray diffraction. Thermal behavior of the layered structure was investigated using thermal analysis, and FT-IR spectroscopy by varying the temperature. The increase in layer spacing of the products by increasing the temperature is also checked by X-ray diffraction. We can suggest three kinds of layered structure by varying the temperature, which is accompanied by changing the intercalated dodecanesulfonate from the monolayer to the bilayer structure or changing the tilt angle.

• 융합신호처리학회논문지
• /
• 제2권2호
• /
• pp.111-118
• /
• 2001

본 연구에서는 패턴 인식용 다층 퍼셉트론 신경망을 순수 디지털 논리회로 모델로 구현할 수 있도록 새로운 논리뉴런의 구조, 디지털 정형 다층논리신경망 구조, 그리고 패턴인식의 응용을 위한 다단 다층논리 신경망 구조를 제안하고, 또한 제안된 구조는 매우 단순하면서도 효과적인 증가적인 가법적(Incremental Additive) 학습알고리즘이 존재함을 보였다.