• Proceedings of the KIEE Conference
• /
• 1995.07c
• /
• pp.1129-1132
• /
• 1995

In the preparation of the layered $BaTiO_3$ thin films with high performance, the new stacking method using the continuous cooling of the substrate was introduced. Amorphous/polycrystalline $BaTiO_3$ layered structure was confirmed by SEM and index of refraction. The layered $BaTiO_3$ thin films formed by the new stacking method showed such a high dielectric constant that the layered structure could not be explained by a stacking structure of the two defined layers but could only be explained by multi-layered structure, i.e. amorphous/micro crystalline/polycrystalline structure. The layered $BaTiO_3$ thin film with a thickness of 240 nm showed higher capacitance per unit area and breakdown strength than the double layered $BaTiO_3$ thin film prepared by the conventional stacking method. And well defined ferroelectric hysteresis leer was observed in the layered $BaTiO_3$ thin film with a thickness of 200 nm.

• Journal of the Korean Ceramic Society
• /
• v.34 no.7
• /
• pp.758-766
• /
• 1997

Non-brittle fracture behaviour of the two composite structures made of two different brittle materials was investigated using 3-point bending test. First, the layered and fibrous macro-composites were fabricated using the material easily formed, yet showing a brittle fracture behaviour similar to ceramics. The layered and fibrous Al2O3 /Al2O3 composites with weak interface were also fabricated using plate of 2 mm thickness and rod of 3 mm diameter respectively. Comparison of the mechanical properties between these two structures was performed in the lights of flexural strength and work of fracture for the composites consisting of Al2O3 and simulated materials respectively. The strength ratio of layered structure to the monolith of same volume was 0.6 and the ratio of fibrous one was about 0.2 for the composites made of simulated brittle material. The ratio of the work of fracture of the fibrous to the layered was 0.47. For Al2O3/Al2O3 composites, the strength ratio of layered and fibrous structures to the monolith with same volume were about 0.6 and 0.2 respectively. The ratio of work of fracture of the fibrous to the layered was 0.6. These confirmed that the layered structure was superior to the fibrous one in terms of flexural strength and work of fracture.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.21 no.7
• /
• pp.1850-1860
• /
• 1996

We present the results for the design ofantireflection (AR) coatings on facets of a multilayered structure waveguide device. The method, whose results agree very well with the reusults of the rigorous method in the case of a symmetric three layer structure deveice, is extended for the design of AR coatings on the facets of a multilayered structure waveguide device. the field profile in a multilayered structure waveguide necessary for the use of the extended method is obtained from the transfer matrix method. The virtual four layered structure method (VFLM) is proposed to reduce the time for the design ofAR coatings because the time for the design of AR coatings using the extended method increases as the number of layers increases. The optimum coating parameters and tolerance mapsfor two different six layered waveguide devices in Ref. [9] and [10] are obtained using the extendedmethod and the VFLM,and for the three different cases approximated as three layered waveguide devices to compare the results of each case. The results of the VFLM are similar to those of the extended methodcompared to those of the three layered structure waveguide. The main reason for the above results is that the field profile in the device calculated usingthe VFLM is similar to that calculated using the extended method compared to that for three layered structure wavegjide. We conclude that the extended method or VFLM should be used for the design of AR coatings on facets of a deice required for the facet reflectivity less than 10$^{-3}$ such as a semiconductor otical amplifier.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.26 no.4
• /
• pp.375-382
• /
• 2016

The mechanical property of a carbon-fiber-reinforced plastic (CFRP) is subjected to two elements, carbon fiber and polymer resin, in a first step and the selection of multi-layered structure is second one. Many combination of fabric layers, i.e. plainweave, twillweave, can be derived for candidates of test specimen used for a basic mechanical components so that a reliable identification of dynamic nature of possible multi-layered structures are essential during the development of CFRP based component system. In this paper, three kinds of multi-layered structure specimens were prepared and the dynamic characteristics of service specimens were conducted through classical modal test process with impact hammer. In addition, the design sensitivity analysis based on transmissibility function was applied for the measured response data so that the response sensitivity for each resonance frequency were compared for three CFRP test specimens. Finally, the evaluation of CFRP specimen over different multi-layered fabric structures are commented from the experimental consequences.

• ETRI Journal
• /
• v.25 no.6
• /
• pp.517-522
• /
• 2003

This investigation confirms that silver stearate consists of an infinite-sheet, two-dimensional, nonmolecular layered structure. Scanning electron microscopy, X-ray diffraction, and infrared spectroscopy reveal the following: plate-like morphology is identified from the SEM image, XRD peaks can be indexed to the (0k0) reflections of a layered structure, and infrared peaks show that alkyl chains are present in an all-trans conformational state with little or no significant gauche population. Based on these structural characteristics, we demonstrate that silver stearate, a prototype of layered organic-inorganic hybrid material, can be grown not only in a designed two-dimensional pattern but also in three-dimensionally ordered ways by using carboxyl-group terminated nanoparticles as a template.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.107-108
• /
• 2015

Layered Double Hydroxides is known as a hydrotalcite-like material. It is a type of anionic clay with planar structure. It is composed of layer structure which is able to exchange anion between two layers which includes divalent ion and trivalent ion. Therefore, layered double hydroxide is applicable for eliminating harmful heavy metals and anionic substances which exist in the concrete. Because it is also able to be used as catalyst and has high possibility of utilization, It is getting an large amount of attention recently. In this study, an analysis on the structure of the layerd double hydroxide (LDH) which is possible to bind the anion was carried out.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.381-382
• /
• 2006

The mechanical behaviors of multi-layered foam core sandwich composite were investigated through a 3-point bending test. The sandwich specimens were obtained from sandwich panel consisting of aluminum faces and urethane foam core. Three types of sandwich specimens such as a single structure, a double structure and a triple structure were considered. The span of sandwich specimens were varied from 170mm to 350mm. According to the results, the flexural and shear properties of multi-layered sandwich composite were found to be higher than those of single-layered sandwich composite.

• Journal of Korean Association for Spatial Structures
• /
• v.11 no.3
• /
• pp.137-145
• /
• 2011

Due to architectural requirement, the attention of single layered freeform spatial structure is increasing nowadays. Because the node of single layered structure should resist the bending and axial forces simultaneously, it is necessary to develop a new proper type of node in detail. In this study, a new type of node for single layered freeform spatial structure was proposed. And the structural performance for the node was analytically evaluated using the commercial FEM software(ABACUS). As a result, a node prototype was selected and the proposed node showed good structural behaviors.

• Journal of the Korean institute of surface engineering
• /
• v.33 no.1
• /
• pp.25-33
• /
• 2000

The synthesis and characterization of intercalated compound of dodecanesulfornate into hydrated metal, [M($H_2$O)\ulcorner](C\ulcornerH\ulcorner$SO_3$)$_2$.$xH_2$O (M=Co, Cu) was presented. The compounds shows a layered structure which was determined by powder X-ray diffraction. Thermal behavior of the layered structure was investigated using thermal analysis, and FT-IR spectroscopy by varying the temperature. The increase in layer spacing of the products by increasing the temperature is also checked by X-ray diffraction. We can suggest three kinds of layered structure by varying the temperature, which is accompanied by changing the intercalated dodecanesulfonate from the monolayer to the bilayer structure or changing the tilt angle.

• Journal of the Institute of Convergence Signal Processing
• /
• v.2 no.2
• /
• pp.111-118
• /
• 2001

In this paper, in order to implement the multi-layered perceptron neural network using pure digital logic circuit model, we propose the new logic neuron structure, the digital canonical multi-layered logic neural network structure, and the multi-stage multi-layered logic neural network structure for pattern recognition applications. And we show that the proposed approach provides an incremental additive learning algorithm, which is very simple and effective.