• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.436-439
• /
• 1997

We investigated a electrical and CO gas sensing properties of pure ZnO and ZnO-ZrO$_2$ composite ceramics. We made 0∼20mo1% ZrO$_2$added ZnO composite ceramics and observed a microstructure of the broken side of the samples. The properties of the samples were studied with temperature, composition, arid a concentration of carbon monoxid. The measured 1000ppm CO sensitivities of pure ZnO were about 1∼1.42, and that of ZnO-ZrO$_2$were about 1∼10.6. In order words, the 1000ppm CO sensitivities of ZnO-ZrO$_2$composite ceramics were about 1∼2 times larger than that of pure ZnO with temperature. The measured 250ppm, 500ppm CO sensitivities of ZnO-ZrO$_2$composite ceramics were about ∼3.28. ∼5.04, respectively.

• Journal of Hydrogen and New Energy
• /
• v.28 no.2
• /
• pp.129-136
• /
• 2017

Characteristics of $ZrO_2$ felt supported Cu/Zn catalysts have been investigated for the production of hydrogen via methanol steam reforming. Cu and Zn in different weight percent were loaded using wet impregnation over $ZrO_2$ felt support. The catalysts were characterized with BET and FE-SEM. The performance of these synthesized catalysts were investigated at SCR=1.5, $GHSV=2000h^{-1}$, temperature=$300{\sim}400^{\circ}C$, and pressure=2.5~19.5 barA. The results showed that the $Cu^{32.5}Zn^{7.5}ZrO_2$ catalyst was most active in terms of methanol conversion and hydrogen production. The methanol conversion in steam reforming of methanol was 84.6% at 19.5 barA and furnace $400^{\circ}C$ over $Cu^{32.5}Zn^{7.5}ZrO_2$ catalyst. The catalysts prepared using $ZrO_2$ felt show higher reactor temperature than the pellet type catalyst at same furnace temperature.

• Bulletin of the Korean Chemical Society
• /
• v.23 no.8
• /
• pp.1135-1138
• /
• 2002

CuO/ZnO, CuO/SiO,sub>2, and CuO/ZrO2 catalysts were prepared for investigating the support effects on methanol dehydrogenation. It was found that the conversion of methanol was proportional to the copper surface area on Cu/ZnO cat alysts and was independent on that on Cu/ZrO2 and Cu/SiO2. The highest copper surface area was obtained with the Cu/ZrO2 (9/1). The unusual deactivation of the Cu/ZnO, which showed the highest selectivity among the catalysts tested, was observed. Pulse reaction with methanol indicated that the lattice oxygen in ZnO could be removed by forming CO2 in the catalytic reaction, supporting that the ZnO reduction was responsible for the severe deactivation of the Cu/ZnO.

• The Korean Journal of Ceramics
• /
• v.4 no.3
• /
• pp.207-212
• /
• 1998

By comparison of the experimental results in two systems of ZnO varistors, it's appear that Sb2O3 is the indispensable element for twining in ZnO varistors and the Zn7Sb2O12 spinel acts as the nucleus to form twins. Al2O3 is not the origin of twining in ZnO varistor, but it was found that Al2O3 could strengthen the twining and form a deformation twining by ZnAl2O4 dragging and pinning effect. The inhibition ratios of grain and nonuniformity of two systems ZnO varistors increase with the increase of Al2O3 content. The twins affect the inhibition of grain growth, the mechanism could be explained follow as: twins increase the mobility viscosity of ZrO grain and grain boundary, and drag ZrO grain and liquid grain boundary during the sintering, then the grain growth is inhibited and the microstructure becomes more uniform.

• Korean Journal of Metals and Materials
• /
• v.49 no.12
• /
• pp.977-982
• /
• 2011

Migration and interaction of multi-protons in a zinc-doped barium zirconate (Zn-doped $BaZrO_3$) super cell were investigated using a density functional theory. O ions in the super cell form interconnected octahedrons with Zr or Zn ions positioned in their centers and Ba ions positioned among the eight octahedrons. When one proton was added to the super cell, the energy barrier of 0.80 eV for proton transfer from the first to second nearest O ion sites from the Zn ion reached its highest value. When two protons were added to the super cell, the two protons preferred the first nearest O ions from the Zn ion. The two protons were accommodated by pushing the neighboring Zn ion further away from the center of the octahedron. Energy barriers for proton transfer from the Zn-octahedron to the neighboring Zr-octahedron were spread in the range of 0.36 ~ 1.02 eV.

• Journal of Welding and Joining
• /
• v.18 no.3
• /
• pp.51-59
• /
• 2000

Sink roll has been used in molten 55%Al-Zn alloy bath of continuous galvanizing line for sinking and stabilizing working steel strip in molten metal bath. In the process, the sink roll body inevitably build up dross compounds and pitting on the sink roll surface during 55%Al-Zn alloy coated strip production, and the life time of the sink roll is shorten by build up dross compounds and pitting. The present study examined the application of thermally sprayed ceramic coatings method on sink roll body for improving erosion resistance at molten 55% Al-Zn pool. In this experiment, the stainless steels such as STS 316L and STS 430F were used as the substrate materials. The CoNiCr and WE-Co powder were selected as bond coating materials. Moreover $Al_2O_3-ZrO_2-SiO_2 and ZrO_2-SiO_2$ powders selected as the top coating materials. Appearances of the specimens before and after dipping to molten 55%Al-Zn pool were compared and analyzed. As a result of this study, STS430F of substrate, WC-Co of bond spray coatings, $ZrO_2-SiO_2$ power of top spray coatings is the best quality in erosion resistance test at molten 55%Al-Zn pool

• Korean Journal of Materials Research
• /
• v.11 no.7
• /
• pp.562-568
• /
• 2001

Devitrifiable solder glass/$ZrB_2$ sintered composites were prepared by using glass with the composition of $60ZnO-20B_2O_3-10SiO_2-10PbO$(in wt%) and $ZrB_2$, powder as starting materials under the $N_2$atmosphere. $ZrB_2$which the good conduction materials showed sensitive oxidation characteristics, because some parts of the $ZrB_2$in specimens changed into the insulated phase of $ZrO_2$. These Phenomena would be estimated that it caused a few amount of residual oxygen in the furnace and/or specimens and the coordination number change of $B_2O_3$ in the glass. The sintering temperature and the mixed ratios of each phase were control of large ranged the resistivity ranged from 10 to 10$^{3}{\Omega}/cm^2$ orders, and to make a conductible microstructure. From these results, it would be explained that the conduction path of $ZrB_2$particles built up within sintered glass matrix.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.208-209
• /
• 2006

Sinterability and microwave dielectric properties of the $Zr1-x(Zn_{1/3}Nb_{2/3})xTiO_4$(x=4, 6) system ceramics have been investigated as functions of zinc-borosilicate(ZBS) glass contents and amount of $Zn_{1/3}Nb_{2/3}O_2$ substitution with a view to applying the composition to LTCC technology. The addition of 25 wt% ZBS glass ensured successful sintering below $925^{\circ}C$. With increasing ZBS glass and $Zn_{1/3}Nb_{2/3}O_2$ contents increased dielectric constant and sinterability but addition ZBS glass decreased the quality factor significantly due to the formation of an excessive liquid and second phases. The sintered $Zr4(Zn_{1/3}Nb_{2/3})6TiO_4$ system ceramics at $925^{\circ}C$ with 25 wt% ZBS glass demonstrated 27.7 in dielectric constant (${\varepsilon}_r$), 3,850 m quality factor($Q{\times}f_0$), and +6 ppm/$^{\circ}C$ in temperature coefficient of resonant frequency($\tau_f$).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1994.11a
• /
• pp.13-16
• /
• 1994

In this paper, xPb(Zn$_{1/3}Nb_{2/3}$)$O_3$-yPbTiO$_3$-zPbZrO$_3$-(0.5wt%)MnO$_2$ ceramics were fabricated by the mixed oxide method sintered at $1250^{\circ}C$ for 2[hr] and then the deielectric, electromechanical coupling factor($K_{p}$ and mechanical coupling factor(Qm) properties were investigated. In 0.1PZN-0.45PT-0.45PZsample, dielectric properties and electromechanical coupling factor were 829 and 29%. In the case of 0.5PZN-0.45PT-0.50PZ sample, that was 101 according to mechanical quality facotr. molphotropic phase boundary(MPB) certained area which $PbTiO_3$addition quatity 40∼50[㏖%].

• Bulletin of the Korean Chemical Society
• /
• v.33 no.10
• /
• pp.3213-3217
• /
• 2012

Reactive adsorption desulfurization (RADS) experiments were conducted over a series of commercial metal oxide supports ($Al_2O_{3-}$, $SiO_{2-}$, $TiO_{2-}$ and $ZrO_{2-}$) supported Ni/ZnO adsorbents. The adsorbents were characterized by X-ray diffraction (XRD), temperature programmed reduction (TPR), and Fourier transform infrared spectroscopy (FTIR) in order to find out the influence of specific types of surface chemistry and structural characteristics on the sulfur adsorptive capacity. The desulfurization performance of all the studied adsorbents decreased in the following order: Ni/ZnO-$TiO_2$ > Ni/ZnO-$ZrO_2$ > Ni/ZnO-$SiO_2$ > Ni/ZnO-$Al_2O_3$. Ni/ZnO-$TiO_2$ shows the best performance and the three hour sulfur capacity can achieve 12.34 mg S/g adsorbent with a WHSV of $4h^{-1}$. Various characterization techniques suggest that weak interaction between active component and support component, high dispersion of NiO and ZnO, high reducibility and large total Lewis acidity of the adsorbents are important factors in achieving better RADS performance.