• 한국분말재료학회지
• /
• 제17권4호
• /
• pp.289-294
• /
• 2010

For the aim of low-temperature co-fired ceramic microwave components, sintering behavior and microwave properties (dielectric constant ${\varepsilon}_r$, quality factor Q, and temperature coefficient of resonant frequency ${\tau}_f$) are investigated in $Bi_{18}O(Ca_{0.725}Zn_{0.275})_8Nb_{12}O_{65}$ [BCZN] ceramics with addition of $V_2O_5$. The specimens are prepared by conventional ceramic processing technique. As the main result, it is demonstrated that the additives ($V_2O_5$) show the effect of lowering of sintering temperature and improvement of microwave properties at the optimum additive content. The addition of 0.25 wt% $V_2O_5$ lowers the sintering temperature to $890^{\circ}C$ utilizing liquidphase sintering and show the microwave dielectric properties (dielectric constant ${\varepsilon}_r$ = 75, quality factor $Q{\times}f$ = 572 GHz, temperature coefficient of resonance frequency ${\tau}_f\;=\;-10\;ppm/^{\circ}C$). The estimated microwave dielectric properties with $V_2O_5$ addition (increase of ${\varepsilon}_r$, decrease of $Q{\times}f$, shift of ${\tau}_f$ to negative values) can be explained by the observed microstrucure (sintered density, abnormal grain structure) and possibly high-permittivity $Bi_{18}Zn_8Nb_{12}O_{65}$ (BZN) phase determined by X-ray diffraction.

• 한국세라믹학회지
• /
• 제28권10호
• /
• pp.757-766
• /
• 1991

These powder properties were investigated and prepared of ultrafine Mn-Zn ferrite powder by Direct-wet process from variation of oxidation condition. H2O2 oxidation the products were ultrafine spherical particles of about 400${\AA}$ in diameter and superparamagnetics. H2O2 and Air oxidation, Coexistance ultrafine spherical particles of about 400${\AA}$ and cubic particles of about 1000${\AA}$. The products were constructed of superparamagnetic and ferromagnetic particles, and Magnetization were about 30 emu/g. Air Oxidation, Above 6 hr Air 120 ι/hr and 4 hr of Air 180 ι/hr were uniform cubic particles of above 1000${\AA}$. The products were ferromagnetic particles and Magnetization of above 45 emu/g.

• 한국세라믹학회지
• /
• 제32권6호
• /
• pp.748-760
• /
• 1995

Pyroelectric properties, figure of merits, and the other properties of the Pb(Zn1/3Nb2/3)O3-Pb(Fe1/2Nb1/2)O3 system, as expected to have excellent pyroelectric properties in the operating temperature range of pyroelectric type infrared sensor, were investigated. In the Pb(Zn1/3Nb2/3)O3-Pb(Fe1/2Nb1/2)O3 system, suppression of the pyrochlore phase depended on sintering condition, as like sintering temperature, holding time, sintering atmosphere. The specimen, sintered by the same composition atmosphere powder at 105$0^{\circ}C$ for 1.5h, possessed the best physical property. It was found that the piezoelectric parameters were mainly depended on the amount of spontaneous polarization and then the 0.2PZN-0.8PFN showed the best pyro- and piezoelectric properties. In terms of the experimental method, two pyroelectric-testing methods, i.e. static and dynamic methods, had a same tendency. Also the result of pyroelectric testing by the static method indicated that the diffuse phase transitiion resulted in the temperature difference of phase transition between dielectric constant and pyroelectric coefficient.

• 한국분말재료학회지
• /
• 제12권6호
• /
• pp.399-405
• /
• 2005

Nanopowders of titanium dioxide $(TiO_2)$ incorporating the transition metal element(s) were synthesized by flame synthesis method. Single element among Fe(III), Cr(III), and Zn(II) was doped into the interior of $TiO_2$ crystal; bimetal doping of Fe and Zn was also made. The characteristics of transition-metal-doped $TiO_2$ nanopowders in the particle feature, crystallography and electronic structures were determined with various analytical tools. The chemical bond of Fe-O-Zn was confirmed to exist in the bimetal-doped $TiO_2$ nanopowders incorporating Fe-Zn. The transition element incorporated in the $TiO_2$ was attributed to affect both Ti 3d orbital and O 2p orbital by NEXAFS measurement. The bimetal-doped $TiO_2$ nanopowder showed light absorption over more wide wavelength range than the single-doped $TiO_2$ nanopowders.

• 한국세라믹학회지
• /
• 제39권12호
• /
• pp.1119-1123
• /
• 2002

Nanostructured spinel NiZn ferrites were prepared by the sol-gel method from metal nitrate raw materials. Analyses by X-ray diffraction and scanning electron microscopy showed the average particle size of NiZn ferrite was under 50 nm. The single phase of NiZn ferrites was obtained by firing at 250${\circ}C$, resulting in nanoparticles exhibiting normal ferrimagnetic behavior. The nanostructured $Ni_{1-X}Zn_XFe_2O_4$ (x=0.0∼1.0) were found to have the cubic spinel structure of which the lattice constants ${\alpha}_2$ increases linearly from 8.339 to 8.427 ${\AA}$ with increasing Zn content x, following Vegard's law, approximately. The saturation magnetization $M_s$ was 48 emu/g for x=0.4 and decreased to 8.0 emu/g for higher Zn contents suggesting the typical ferrimagnetism in mixed spinel ferrites. Pure NiZn ferrite phase substituted by Cu was observed before using the additive but hematite phase was partially appeared at $Ni_{0.2}Zn_{0.2}Cu_{0.6}Fe_2O_4$. On the other hand, the hematite phase in this NiZn Cu ferrite was disappeared after using the additive of acethyl aceton with small amount. The saturation magnetization Ms of $Ni_{0.2}Zn_{0.8-y}Cu_yFe_2O_4$(y=0.2∼0.6) as measured was about 51 emu/g at 77K and 19 emu/g at room temperature, respectively.

• 한국분말재료학회지
• /
• 제15권2호
• /
• pp.95-100
• /
• 2008

The investigation is to modify the mechanical and chemical properties of Mg alloys using a combination of rapid solidification and surface treatment. As the first approach, $Mg_{95}Zn_{4.3}Y_{0.7}$ was gas atomized and pressure sintered by spark plasma sintering process (SPS), showing much finer microstructure and higher strength than the alloys as cast. Further modification was performed by treating the surface of PM Mg specimen using Plasma electrolytic oxidation (PEO) process. During the PEO processing, MgO layer was initiated to form on the surface of Mg powder compacts, and the thickness and the density of MgO layer were varied with the reaction time. The thickening rate became low with the reaction time due to the limited diffusion rate of Mg ions. The surface morphology, corrosion behavior and wear resistance were also discussed.

• 한국진공학회지
• /
• 제19권1호
• /
• pp.58-65
• /
• 2010

먼저 RF 마그네트론 스퍼터링법을 이용하여 사파이어 기판 위에 AlN 박막을 증착하였다. AlN 공급원으로는 분말소결된 AlN 타겟을 적용하였다. 플라즈마 파워를 50에서 110 W로 증가시켰을 때 AlN 층의 두께는 선형적으로 증가하였다. 그러나 동작압력을 3에서 10 mTorr로 증가시켰을 때는 동작기체인 아르곤 양이 증가함에 따라 AlN 타겟으로부터 스퍼터링되어 나온 AlN 입자들의 평균자유행정의 거리가 감소하기 때문에 AlN 층의 두께는 약간 감소하였다. 질소 기체를 아르곤과 섞어주었을 때는 질소의 낮은 스퍼터링 효율에 의해서 AlN의 두께는 크게 감소하였다. 다음으로는 ZnO 형판 위에 AlN를 증착하였다. 그러나 700도 이상의 열처리에 의해서 AlN와 ZnO의 계면이 약간 분리되어 계면의 열적 안정성이 낮다는 결과를 얻었다. 게다가 스퍼터링으로 증착한 AlN 박막의 나쁜 결정성으로 인하여 700도에서 MOCVD의 반응기 기체인 수소와 암모니아에 의해서 AlN 밑의 ZnO 층이 분해되는 현상도 관찰하였다. 그리고 900도 이상에서는 ZnO가 완전히 분해되어 AlN 박막이 완전히 분리되었다.

• 자원리싸이클링
• /
• 제1권1호
• /
• pp.58-68
• /
• 1992

아연을 함유하고 있는 산업폐기물로부터 첨단산업의 소재원료인 미립의 고순도 ZnO 분말을 아연제련의 용매추출 공정에서 직접 합성할 수 있는 방법을 개발하고자 하였다. 아연 함량이 55%인 선재산업의 폐기물을 황산으로 침출하여 아연을 추출하였다. 함아연 용액에서 철분을 침전시켜 제거한 후 D2EHPA를 추출제로 사용하는 용매추출에 의해 아연이온을 유기상으로 추출하여 정제한 뒤 oxalic acid와 같은 침전제를 사용하여 유기상의 아연 이온을 precipitation stripping 법으로 탈거, 침전시켜 $ZnC_2O_4$ 분말을 합성하였으며 이를 해소하여 99.9% 이상의 ZnO 분말을 제조하였다. 황산농도, 침출시간, 황액농도가 아연의 침출율에 미치는 영향과 용매추출시 용액의 산도에 따른 아연과 불순물의 추출거동을 조사하여 최적정제조건을 얻었다. 또한 oxalic acid의 농도, 온도, 계면활성제의첨가, 침전시간 등이 생성된 $ZnC_2O_4$ 분말의 형상과 입자크기 및 분포에 미치는 영향에 대해 조사하였다.

• 한국결정성장학회지
• /
• 제33권1호
• /
• pp.15-21
• /
• 2023

산화아연 분말을 제조하기 위해 3종류의 나트륨계 알칼리 침전제인 수산화나트륨, 탄산나트륨, 수산화나트륨/탄산수소나트륨을 이용하여 반응에 따른 열역학적 고찰과 아연 침전생성물로부터 산화아연 분말 제조 공정의 차이점을 비교하였다. 나트륨계 알칼리 침전제와의 반응으로 생성된 아연 침전생성물은 각각 히드록시염화아연(Zn₅(OH)₈Cl₂·H₂O)과 탄산아연수산화물 (Zn₅(OH)₆(CO₃)₂·H₂O)임을 XRD를 통해 확인하였다. 나트륨계 알칼리 침전제에 따라 800℃에서 열처리하여 생성된 산화아연 입자 크기를 비교하였다. 혼합된 수산화나트륨 및 탄산수소나트륨의 알칼리 침전제 반응으로 보다 균일한 산화아연 입자를 제조할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.172-172
• /
• 2008

By thermal evaporation method, well-aligned ZnO nanowires were synthesized on sapphire substrate at $1000^{\circ}C$ with different oxygen flow rate by using pure ZnO powder (99.999 %). The as-synthesized ZnO nanowires were characterized by field emission scanning electron microscopy (FESEM) and transmission electron microscopy (TEM). The well-aligned nanowires are single crystalline in nature and perpendicularly grown along the c-axis. Also the growth rate of nanowires, such as diameter and length, had a tendency to increase as oxygen flow rate increased. Based on the PL measurement of ZnO nanowires, we found that the near band edge of emission redshifted with the increasing intensity of the defect-related green emission in proportion to the increase of oxygen flow rate. "This research was supported by the Korea Research Foundation Grant funded by the Korean Government(MOEHRD)" (The Regional Research Universities Program/Chungbuk BIT Research-Oriented University Consortium).