• Corrosion Science and Technology
• /
• 제9권1호
• /
• pp.34-38
• /
• 2010

Electrochemical study on cut edge corrosion of prepainted Zn coated (GI) and 55%Al-Zn coated (GL) steels has been performed in wet-dry cyclic conditions. Maximum width of delaminated polymer coating from the cut edge for GI and GL specimens was evaluated under wet-dry cyclic conditions. The cyclic tests were carried out for 1000 h by changing of relative humidity, where the salt of NaCl was deposited on the specimen every 48 h. The cut edge corrosion test under NaCl deposit indicated that the delamination of the GL specimen progresses at a higher rate than the GI. The electrochemical corrosion monitoring was also performed under condition of alternate exposure to immersion in NaCl solution and drying at 60%RH and $25^{\circ}C$. On the basis of the results of the delamination tests and electrochemical measurements, the mechanism of cut edge corrosion for GI and GL were discussed.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2003년도 춘계총회 및 연구발표회 초록집
• /
• pp.125.2-125
• /
• 2003

• 센서학회지
• /
• 제28권2호
• /
• pp.101-105
• /
• 2019

ZnS substrates with excellent transmittance in the mid-infrared region ($3-5{\mu}m$) were prepared using hot pressing instead of conventional chemical vapor deposition (CVD). Diamond-like carbon(DLC) was coated on either one or both sides of the ZnS substrates to improve their mechanical properties and transmittance. More specifically DLC was coated using CVD with an Ar and $C_2H_2$ mixed gas, and Ge was used as the bonding layer. During CVD, the bias voltage was fixed to 500 V and analyzed by Fourier transform infrared spectroscopy (FT-IR), nanoindenter, scanning electron microscope and energy dispersive spectrometry. Results of hardness analysis using the nanoindenter, showed that DLC coating increased from 5.9 to 17.7 GPa after deposition. The FT-IR spectroscopy results showed that, in the mid-infrared region ($3-5{\mu}m$), the average transmittance of the samples with DLC coating on one and both sides increased by approximately 6% and approximately 11.2% respectively. In conclusion, the DLC coating improved the durability and transmittance of the ZnS substrates.

• 한국표면공학회지
• /
• 제54권3호
• /
• pp.144-151
• /
• 2021

In the present work, planar-type ZnO powder of [0001] plane with a high aspect ratio range of 20:1 to 50:1 was synthesized. Ag or CuO could be coated on the planar-type ZnO powder by wet methods such as centrifugation or ball milling. During the coating, the average size of the powder was slightly increased while maintaining the shape and XRD pattern of ZnO. When Ag or CuO was coated, the absolute value of the zeta potential, as well as the concentration of oxygen vacancy, was increased. Ag or CuO coated planar-type ZnO power exhibited excellent antibacterial performance, which seems to be related to their high electrostatic attraction force. They could be made into a masterbatch by mixing with ABS resin, and their applicability to antibacterial substances was confirmed by manufacturing the caps of a keyboard.

• 대한화장품학회지
• /
• 제30권2호
• /
• pp.173-180
• /
• 2004

20-30nm 크기를 갖는 나노 사이즈 ZnO 입자는 염료, 러버 첨가제, 가스 센서, 바리스터, 감광제와 광촉매로서 여러 산업분야에서 사용되고 있다. 반면에 화장품 산업에서는 나노 미터 크기의 ZnO 입자는 UV 차단물질과 자연스러운 메이크업 효과를 증진시키는 소재로서 사용되고 있다. 그러나 순수 ZnO 입자는 화장품에 적용했을 때 사용감 악화로 인해 그 사용량이 제한되고 있는 실정이다. 따라서 본 논문에서는 사용감은 판상 분체의 특성을 갖으면서 ZnO 본연의 특성을 유지하는 분체를 합성하기 위해 화장품 산업에서 널리 사용되고 있는 세리사이트, 보론나이트라이드, 비스무스옥시클로라이드와 같은 판상분체에 나노 사이느 ZnO가 코팅된 고기능성 무기복합분체를 하였다. 본 논문에서는 열수침전법에 의해 무기복합분체를 합성하였다. Zn원으로서 ZnCl$_2$가 사용되었고 침전제로는 hexamethylenetetramine(HMT)과 urea를 사용하였다. 실험변수로서 출발물질의 농도, 침전제의 종류, 핵생성제의 농도, 반응온도와 반응시간을 변화시켜 실험하였다. 합성된 무기복합분체의 형태, 결정상 변화, 열특성, UV-차단효과를 관찰하기 위해 각각 FE-SEM, XRD, FT-IR, TGA-DTA, In vitro SPF 테스터 기기를 이용하여 확인하였다. 합성된 무기복합분체를 메이크업 제품에 적용시켜 사용감 테스트하였다. 본 실험 결과 판상분체의 종류에 상관없이 일정한 합성조건 범위에서 나노크기 ZnO 입자가 균일하게 코팅되었다. 코팅된 판상분체를 프레스트 파우더제품에 적용시켜 사용자 테스트한 결과 판상분체 특유의 광택은 현저히 감소되는 반면 자연스러운 화장 연출, 사용감 개선 및 부착력 향상 효과를 얻을 수 있었다.

• 대한금속재료학회지
• /
• 제48권6호
• /
• pp.533-542
• /
• 2010

The specific motivation for joining an Al alloy and Zn-coated steel arises from the need to save fuel consumption by weight reduction and to enhance the durability of vehicle structures in the automobile industry. In this study, the lap joining A6K31 Al alloy (top) and SGARC340 Zn-coated steel (bottom) sheets with a thickness of 1.0 mm and 0.8 mm, respectively, was carried out using the friction stir weld (FSW) technique. The probe of a tool did not contact the surface of the lower Zn-coated steel sheet. The friction stir welding was carried out at rotation speeds of 1500 rpm and travel speeds of 80~200 mm/min. The effects of tool geometry and welding speed on the mechanical properties and the structure of a joint were investigated. The tensile properties for the joints welded with a larger tool were better than those for the joints done with a smaller tool. A good correlation between the tensile load and area of the welded region were observed. The bond strength using a larger tool (M4 and M3) decreased with an increase in welding speed. Most fractures occurred along the interface between the Zn-coated steel and the Al alloy. However, in certain conditions with a lower welding speed, fractures occurred at the A6K31 Al alloy.

• 한국표면공학회지
• /
• 제49권5호
• /
• pp.472-476
• /
• 2016

The nano-array of the vertically aligned rod-like particles grown on ZnO coated glass-substrates was obtained via hydrothermal process. ZnO thin film coatings were prepared on the glass substrates using a MOD (metallorganic deposition) dip-coating method with zinc chloride dihydrate as starting material and 2-ethylhexanol as solvent. ZnO nanorods were synthesized on the seeded substrates by hydrothermal method at $80^{\circ}C$ using zinc-nitrate hexahydrate as a Zn source and sodium hydroxide as a mineralizer. Under the hydrothermal condition, the rod-like nanocrystals were easily attaching on the already ZnO seeded (coated) glass surface. It has been shown that the hydrothermal synthesis parameters are key factors in the nucleation and growth of ZnO crystallites. By controlling of hydrothermal parameters, the ZnO particulate morphology could be easily tailored. Rod-shaped ZnO arrays on the glass substrates consisted of elongated crystals having 6-fold symmetry were predominantly developed at high Zn precursor concentration in the pH range 7~11.

• 연구논문집
• /
• 통권23호
• /
• pp.109-120
• /
• 1993

A study on corrosion and adhesion properties of evaporated Zn-Cr films were conducted on steel strip by two-source evaporater. Corrosion resistance of Zn-Cr coated steel was evaluated by salt spray test in 5% NaCl. Adhesion property of Zn-Cr films on steel substrate was evaluated by tape test after $180^\circC$ bending. Adhesion was improved with increasing the Cr content and reached the maximum at the Cr content of 6 to 8wt%. Corrosion resistance was enhanced with increasing the Cr content and improved by rolling Zn-Cr coated specimen, as a post-treatment.

• Macromolecular Research
• /
• 제10권6호
• /
• pp.369-372
• /
• 2002

The use of ZnO and stearic acid is very well known in sulfenamide accelerated sulfur vulcanization of diene elastomers. Zn-ion coated nano filler has been developed and tested, in styrene-butadiene rubber (SBR) as sulfur vulcanizing activator cum reinforcing filler. In this study Zinc oxide has been replaced by the Zn-ion coated nano silica filler with an aim to study the dual role of this nanofiller in SBR. The presence of Zn-ion on the nano silica filler surface activates the sulfur vulcanization by involving Zn++ in to the sulfurating complex formed with thiazole from sulfenamide. The increase of Zn-ion, on the nanofiller, decrease the scorch safety of the elastomer compound but increase the tensile strength, state of cure and tear strength and attain maximum at its 10% level. The presence of stearic acid increases the rate of vulcanization. Replacement of stearic acid with mono-stearate, however, increases the vulcanization rate but decrease the ultimate state of cure. A mechanistic scheme involving dual function of this nanofiller has been suggested.

• 대한환경공학회지
• /
• 제31권7호
• /
• pp.541-548
• /
• 2009

본 연구에서는 매립장 침출수 같은 중금속과 유기물을 함께 함유하고 있는 폐수를 처리하기위하여, Fe(III)을 활성탄, 모래, 불가사리와 같은 담체에 첨착 및 코팅시킨 흡착제를 사용하였다. 제조된 Iron Impregnated Activated Carbon(Fe-AC), Iron Coated Sand(ICS), Iron Coated Starfish(ICSF)는 EPA 3050B 방법을 통하여 각 매질에 함유된 철 함량을 분석하였으며, 회분식 반응조에서의 흡착실험을 통하여 각 흡착제의 Mn(II), Zn(II) 및 Cu(II)의 제거성능을 비교하였다. Fe-AC 및 ICS의 철 함유량은 각각 1,612 mg/kg 및 1,609 mg/kg으로서 매우 유사하였으며 ICSF의 철 함유량은 1,768 mg/kg으로 ICSF의 철 코팅함량이 다른 두 가지에 비해 150 mg/kg 정도 높게 나타났다. 회분식 실험에서의 Mn(II), Zn(II), Cu(II)의 제거효율은 ICSF, Fe-AC, ICS의 순으로 높은 제거율을 보였다. 각 흡착제를 단일 및 다중층으로 충전한 칼럼반응기에 의한 연속식 실험결과, 단일 흡착제에 비해 ICS, Fe-AC, ICSF의 순으로 충전한 시스템에서 높은 중금속 및 페놀제거효율을 나타내었으며, Cu(II)와 Zn(II)에 대해서는 뚜렷한 파과능을 보였으나 Mn(II) 제거율은 상대적으로 낮게 나타났다. 각 흡착제를 병합 충전한 다중층 칼럼반응시스템은 중금속 및 phenol제거에 효과적임을 알 수 있었다.