• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.345.2-345.2
• /
• 2016

Alumina (Al2O3) doped zinc oxide (ZnO) films (AZO) have been prepared from 2 wt.% Al2O3 doped ZnO target by DC magnetron sputtering at a 2 mTorr (0.27 Pa) chamber pressure in (15 sccm) argon ambient. We obtained films of various opto-electronic properties by variation of target angle from 32.5o to 72.5o. At lower target angle deposited films show higher values in optical gap, mobility of charge carrier, carrier concentration, crystallite grain size, transmission range of wavelength, which are favorable characteristics of AZO as a transparent conducting oxide (TCO). At higher target angle the sheet resistance, work function, surface roughness for the AZO films increases. Measured haze ratio of the films changed lower to higher and size of characteristic surface structure of as deposited film ranges from ~40 nm to ~300 nm. By a combination of low and high target angle we obtained a textured TCO film with high conductivity.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.271-272
• /
• 2006

Zinc confers high corrosion resistance by acting as a sacrificial anode, and a zinc coating improves the appearance of steel. Chromate conversion coating (CCC) films are still one of the most efficient surface treatments for steel. Although such films can self-repair via the dissolution of Cr(VI), dissolved Cr(VI) have adverse effects on humans, and the environment. Therefore, we examined the corrosion protection property and morphology of colloidal silica conversion films as an alternative to CCC films. The corrosion behavior was investigated in 3% NaCl solution using electrochemical techniques, including electrochemical impedance spectroscopy, open circuit potential, and the salt spray test(SST). Corrosion was implied by the appearance of red rust on the specimen surface. In corrosion resistance at 3% NaCl solution, red rust appeared at 15-20, 55-70, and 83-98 days on Zn-electroplated steel, colloidal silica conversion-coated specimens, and CCC-coated specimens, respectively. In the salt spray test, the colloidal silica film provided better corrosion protection than CCC films, i.e., red rust appeared at 96 hours on the Zn-electroplated steel sheet, at 432 hours with the CCC films, and at 888 hours with silica conversion coating.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.4
• /
• pp.406-413
• /
• 2004

In this study, we investigated the reflection coefficient of absorbers fur mobile phone on average Particle size and preparation temperature of specimens. We used recycled MnZn ferrite with initial permeability of 2,500 and 10,000 as starting materials. Absorption ability increased at 1.8 ㎓ which is frequency fur mobile phones with increasing average particle size. We developed a sheet type electromagnetic wave absorber with the thickness of 1 mm which showed reflection coefficient of -3.8 ㏈ at 1.8 ㎓.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.271-274
• /
• 1999

In this paper, we studied the matrix type Powder AC Electroluminescence using ZnS:Cu,Cl Phosphor. Previously, Powder AC EL was used in Backlighting of LCD. Rescently, organic Thin Film EL was rapidly developed because of high Luminescence and low applied voltage. But Powder AC EL has Superior features that include sheet like flexibility thickness, low weight, self-emission, a wide viewing angle and a fast response time. We tried to change of phosphor thickness and binder mixture rate in order to obtain the good condition of powder AC EL and we obtained the very low breakdown voltage that was just 15V. Till now, we measured the current-voltage(V-I), luminance-voltage(V-L), Luminance-current (L-I), color coordinate (CIE), and phosphor Intensity of variable thickness. In experiment result, the devices has the luminance of 840 cd/$m^2$ and improved color coordinate, x=0.1557, y=0.2145, using a 10kHz drive frequency.

• Proceedings of the KWS Conference
• /
• 2003.05a
• /
• pp.99-101
• /
• 2003

This study deals with the resistance spot welding of aluminized steels. According to the test results it was clear that the weldability of aluminized steels was equivalent to or better than that of Zn coated steel. Microstructural inspection revealed that molten aluminum that was repelled from the weld during the process, piled up at the split zone. The test results also demonstrated that the weld metal of aluminized steels could hardly produce the weld crack even higher welding heat Input was applied.

• Journal of Microbiology and Biotechnology
• /
• v.4 no.4
• /
• pp.364-366
• /
• 1994

Molecular properties of streptococcal nuclease purified from Streptococcus sp. were examined. The purified enzyme was stable in the range of pH 7 to 10 and easily inactivated above $60^{\circ}C$. Atomic spectroscopy analysis indicated that the enzyme contains Ca, Mg, Zn. Circular dichroism study showed 25% $\alpha$ -helix, 15% $\beta$-sheet and 30% $\beta$-tums.

• Proceedings of the Korean Nuclear Society Conference
• /
• 2005.10a
• /
• pp.237-238
• /
• 2005

• Journal of Sericultural and Entomological Science
• /
• v.45 no.2
• /
• pp.121-125
• /
• 2003

Dissolution of Antheraea pernyi silk fiber was carried out in a zinc nitrate 6 hydrate (Zn(NO$_3$)$_2$ㆍ6$H_2O$) solution with various dissolving conditions. The solubility was significantly dependent on the concentration of zinc nitrate, dissolving temperature and time. Regenerated A. pernyi silk fibroin powder was obtained through dialysis process to remove chaotropic salt. FTIR and X-ray diffractometer showed that the conformation of regenerated A. pernyi silk powder was sheet structure.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.12
• /
• pp.2014-2018
• /
• 2016

Transparent, conductive electrode films, showing the particular characteristics of good conductivity and high transparency, are of considerable research interest because of their potential for use in opto-electronic applications, such as smart window, photovoltaic cells and flat panel displays. Multilayer transparent electrodes, having a much lower electrical resistance than widely-used transparent conducting oxide electrodes, were prepared by using RF/DC magnetron sputtering system. The multilayer structure consisted of three layers, [NiInZnO(NIZO)/Ag/NIZO]. The optical and electrical properties of the multilayered NIZO/Ag/NIZO structure were investigated in relation to the thickness of each layer. The optical and electrical characteristics of multilayer structures have been investigated as a function of the Ag and NIZO film thickness. High-quality transparent conductive films have been obtained, with sheet resistance of $9.8{\Omega}/sq$ for Ag film thickness of 8 nm. Also the multilayer films of inserted Ag 8 nm thickness showed a high optical transmittance above 93% in the visible range. The electrical and optical properties of the new multilayer films were mainly dependent on the thickness of Ag insertion layer.

• Korean Journal of Metals and Materials
• /
• v.48 no.6
• /
• pp.533-542
• /
• 2010

The specific motivation for joining an Al alloy and Zn-coated steel arises from the need to save fuel consumption by weight reduction and to enhance the durability of vehicle structures in the automobile industry. In this study, the lap joining A6K31 Al alloy (top) and SGARC340 Zn-coated steel (bottom) sheets with a thickness of 1.0 mm and 0.8 mm, respectively, was carried out using the friction stir weld (FSW) technique. The probe of a tool did not contact the surface of the lower Zn-coated steel sheet. The friction stir welding was carried out at rotation speeds of 1500 rpm and travel speeds of 80~200 mm/min. The effects of tool geometry and welding speed on the mechanical properties and the structure of a joint were investigated. The tensile properties for the joints welded with a larger tool were better than those for the joints done with a smaller tool. A good correlation between the tensile load and area of the welded region were observed. The bond strength using a larger tool (M4 and M3) decreased with an increase in welding speed. Most fractures occurred along the interface between the Zn-coated steel and the Al alloy. However, in certain conditions with a lower welding speed, fractures occurred at the A6K31 Al alloy.