• 공업화학
• /
• 제18권1호
• /
• pp.24-28
• /
• 2007

$Cl_2/Ar$ 가스의 고밀도 플라즈마를 이용하여 ZnO 박막에 대한 식각이 연구되었다. $Cl_2$ 가스의 농도, coil rf power, dc-bias 전압, 그리고 공정 압력을 변화시켜서 ZnO 박막의 식각특성을 체계적으로 조사하였다. $Cl_2$ 가스의 농도가 증가할수록 ZnO 박막의 식각 속도는 증가하였고, 식각된 패턴 주변의 재증착은 감소되었지만 식각된 패턴의 측면 경사는 낮아졌다. Coil rf power와 dc-bias 전압이 증가할수록 ZnO 박막의 식각 속도가 증가하였고, 식각 프로파일이 개선되었다. 공정 압력이 증가 할수록 ZnO 박막의 식각 속도가 미세하게 증가하였으나 식각 프로파일의 변화는 관찰되지 않았다. 이러한 결과들을 토대로 하여 ZnO 박막의 최적의 식각 조건이 설정되었다. 재증착이나 잔류물이 없이 대략 $75^{\circ}{\sim}80^{\circ}$의 높은 이방성 식각을 갖는 ZnO 박막의 식각이 20% $Cl_2$ 가스의 농도, 1000 W의 coil rf power, 400 V의 dc-bias 전압, 그리고 5 mTorr의 공정 압력에서 성공적으로 이루어졌다.

• 한국진공학회지
• /
• 제17권1호
• /
• pp.73-79
• /
• 2008

투명 전도성 산화물 전극(transparent conductive oxide electrodes)에 적용하기 위하여 RF 마그네트론 스퍼터링 방법에 의해 유리 기판 위에 산화아연 박막을 증착하였다. 투명 전극으로써 응용되기 위한 최적의 조건으로 기판온도를 상온으로 유지하고 RF power 200 W, 타겟과 기판사이의 거리(Dts)가 30 mm일 때 증착된 산화아연 박막으로부터 가장 낮은 비 저항값($7.4{\times}10^{-3}{\Omega}cm$)을 얻어 낼 수 있었으며, 85% 이상의 높은 투과율을 만족하는 박막을 얻을 수 있었다. 실질적인 소자로써의 응용을 위해 photo lithography를 통한 pattern을 형성, 습식 식각을 통하여 그 특성을 알아보고자 하였다. 습식 식각에서 사용된 식각용액(etchant)으로는 다양한 산 용액(황산, 옥살산, 인산)을 사용하였으며, 산의 농도 변화에 따른 식각특성과 식각시간 및 식각 이미지(표면형상)의 변화를 알아보았다. 결과적으로 산화아연의 습식식각은 산의 종류와 무관하게 산 용액의 농도(즉, pH)에 크게 의존하며, pH가 증가함에 따라 식각율이 지수함수적으로 감소하고 아울러 다양한 식각 이미지가 나타남을 최초로 고찰할 수 있었다.

• Transactions on Electrical and Electronic Materials
• /
• 제12권2호
• /
• pp.51-55
• /
• 2011

We investigated the etching characteristics of zinc oxide (ZnO) thin films deposited by the atomic layer deposition method. The gases of the inductively coupled plasma chemistry consisted of $Cl_2$, Ar, and $O_2$. The maximum etch rate was 40.3 nm/min at a gas flow ratio of $Cl_2$/Ar=15:5 sccm, radio-frequency power of 600 W, bias power of 200 W, and process pressure of 2 Pa. We also investigated the plasma induced damage in the etched ZnO thin films using X-ray diffraction (XRD), atomic force microscopy and photoluminescence (PL). A highly oriented (100) peak was present in the XRD spectroscopy of the ZnO samples. The full width at half maximum value of the ZnO sample etched using the $O_2/Cl_2$/Ar chemistry was higher than that of the as-deposited sample. The roughness of the ZnO thin films increased from 1.91 nm to 2.45 nm after etching in the $O_2/Cl_2$/Ar plasma chemistry. Also, we obtained a strong band edge emission at 380 nm. The intensities of the peaks in the PL spectra from the samples etched in all of the chemistries were increased. However, there was no deep level emission.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.926-929
• /
• 2007

A significant progress has been made in the characterization of zinc oxide (ZnO) semiconductor as a new semiconductor layer instead of amorphous Si semiconductor used in thin film transistor due to its high electron mobility at low deposition temperature which is quite suitable for flexible display and OLED devices. The wet pattering of ZnO is another important issue with regard to mass production of ZnO thin film transistor device. However, the wet behavior of ZnO thin film in aqueous wet etching solutions conventionally used un TFT industry has not been reported yet, in this work, wet corrosion behavior of RF magnetron sputtered ZnO thin film in various wet solutions such as phosphoric and nitric acid solutions was studied using by electrochemical analysis. The effects of deposition parameters such as RF power and oxygen partial pressure on corrosion rate are also examined.

• 한국전기전자재료학회논문지
• /
• 제26권12호
• /
• pp.894-898
• /
• 2013

Zinc oxide(ZnO) was sputtered on various glass and flexible substrates such as polyethylene terephthalate(PET) and polycarbonate(PC). A Q-switched $Nd:YVO_4$ laser with a wavelength of 1,064 nm was used for the direct etching of ZnO films. It was possible to obtain laser etched line patterns on the ZnO films on PC substrate at some specific laser beam conditions. In the flexible substrates, more thermal energy of laser beam is expected to be spreaded for the etching process.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.181-185
• /
• 2007

We report on our material and process research on ZnO:Al films and on our investigations on wet chemical etching using a variety of etching solutions. We achieve resistivity as low as $750{\mu}{\Omega}cm$ for ZnO:Al films with film thickness of 140 nm. Etching with phosphorous acid allows for accurate fine patterning of the ZnO:Al films on glass substrates.

• 한국전기전자재료학회논문지
• /
• 제25권5호
• /
• pp.377-380
• /
• 2012

Laser direct patterning of indium tin oxide(ITO) is one of new methods of direct etching process to replace the conventional photolithography. A diode pumped Q-switched Nd:$YVO_4$ (${\lambda}$= 1,064 nm) laser was used to produce ITO electrode on various transparent oxide semiconductor films such as zinc oxide(ZnO). The laser direct etched ITO patterns on ZnO were compared with those on glass substrate and were considered in terms of the overlapping rate of laser beam. In case of the laser etching on double-layer, it was possible to obtain the higher overlapping rate of laser beam.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2010년도 춘계학술발표대회
• /
• pp.27.2-27.2
• /
• 2010

In recent years, there is a strong requirement of low cost, stable microelectro mechanical systems (MEMS) for resonators, microswitches and sensors. Most of these devices consist of freely suspended microcantilevers, which are usually made by the etching of some sacrificial materials. Herein, we have attempted to use Si nanowires, inherited from the parent Si wafer, as a sacrificial material due to its porosity, low cost and ease of fabrication. Prior to the fabrication of the Si nanowires silver nanoparticles were continuously formed on the surface of Si wafer. Vertically aligned Si nanowires were fabricated from the parent Si wafers by aqueous chemical route at $50^{\circ}C$. Afterwards, the morphological and structural characteristics of the Si nanowires were investigated. The morphology of nanowires was strongly modulated by the resistivity of the parent wafer. The 3-step etching of nanowires in diluted KOH solution was carried out at room temperature in order to control the fast etching. A layer of $Si_3N_4$ (300 nm) was used for the selective fabrication of nanowires. Finally, a freely suspended bridge of zinc oxide (ZnO) was fabricated after the removal of nanowires from the parent wafer. At present, we believe that this technique may provide a platform for the inexpensive fabrication of futuristic MEMS.

• Restorative Dentistry and Endodontics
• /
• 제5권1호
• /
• pp.13-18
• /
• 1979

The purpose of this study was to measure the roughness on the acid -etching surface. The etching agents of three-kinds composite resins were used to etch the tooth surface. Newly extracted I5-anterior teeth were invested with self-curing acrylic resin, and the labial surface was exposed. The exposed labial side was polished with abrasive papers and finally polished on polishing machine with zinc oxide powder. After the teeth were polished, the specimens were washed by water and dried by air. Surface roughness tester, Taylor-Habson's Taly Surf-10, (Fig-1) was used to measure roughness of this unetched tooth surface. And that, the specimens were divided into three groups. The first group was etched with Restodent etchant, the second group was etched with Nuva-system etchant, and Hi-pol etching agent was used in the third group. And the surface roughness tester was used to measure roughness of the etching teeth surface. The results obtained were as follows. 1. The roughness of acid-etched enamel were increased $2{\mu}m$ to $6{\mu}m$. 2. Hi-pol etchant produced the smoothest surface($2.3{\mu}m$). 3. Restodent etchant($3.8{\mu}m$) and Nuva-system etchant($3.7{\mu}m$) produced rougher surface than Hi-pol.

• Journal of Information Display
• /
• 제12권1호
• /
• pp.47-50
• /
• 2011

Highly stable amorphous indium.gallium.zinc-oxide (a-IGZO) thin-film transistors (TFTs) were fabricated with an etchstopper and via-hole structure. The TFTs exhibited 40 $cm^2$/V s field-effect mobility and a 0.21 V/dec gate voltage swing. Gate-bias stress induced a negligible threshold voltage shift (${\Delta}V_{th}$) at room temperature. The excellent stability is attribute to the via-hole and etch-stopper structure, in which, the source/drain metal contacts the active a-IGZO layer through two via holes (one on each side), resulting in minimized damage to the a-IGZO layer during the plasma etching of the source/drain metal. The comparison of the effects of the DC and AC stress on the performance of the TFTs at $60^{\circ}C$ showed that there was a smaller ${\Delta}V_{th}$ in the AC stress compared with the DC stress for the same effective stress time, indicating that the trappin of the carriers at the active layer-gate insulator interface was the dominant degradation mechanism.