• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.2
• /
• pp.49-55
• /
• 2001

ZnO films were fabricated on p-type Si(100) wafer ITO glass and quartz glass by the sol-gel process using zinc acetate dihydrate as starting material. A homogeneous and stable solution was prepared by dissolving the zinc acetate dihydrate in a solution of 2-methoxyethanol and monoethanolamine (MEA). ZnO films were deposited by spin-coating at 2800 rpm for 25 s and were dried on a hot plate at $250^{\circ}C$ for 10 min. Crystallization of the films was carried out at $400^{\circ}C$~$800^{\circ}C$ for 1 h in air. X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM), UV-vis transmittance spectroscopy, FTIR transmittance spectroscopy and Photoluminescence (PL) spectroscopy measurements have been used to study the structural and optical properties of the films. ZnO films highly oriented along the (002)plane were obtained. In all cases the films were found to be transparent (above 70%) in visible range with a sharp absorption edge at wavelengths of about 380nm, which is very close to the intrinsic band-gap of ZnO(3.2 eV). The low temperature band-edge photoluminescence revealed a complicated multi-line structure in terms of bound exciton complexes and the phonon replicas.

• Transactions on Electrical and Electronic Materials
• /
• v.18 no.3
• /
• pp.155-158
• /
• 2017

In this paper, ZnO Thin Film Transistors (TFTs) were fabricated by a sol-gel method using a low-temperature process, and their physical and electrical characteristics were analyzed. To lower the process temperature to $200^{\circ}C$, we used a zinc nitrate hydrate ($Zn(NO_3)_2{\cdot}xH_2O$) precursor. Thermo Gravimetric Analyzer (TGA) analysis showed that the zinc nitrate hydrate precursor solution had 1.5% residual organics, much less than the 6.5% of zinc acetate dihydrate at $200^{\circ}C$. In the sol-gel method, organic materials in the precursor disrupt formation of a high-quality film, and high-temperature annealing is needed to remove the organic residuals, which implies that, by using zinc nitrate hydrate, ZnO devices can be fabricated at a much lower temperature. Using an X-Ray Diffractometer (XRD) and an X-ray Photoelectron Spectrometer (XPS), $200^{\circ}C$ annealed ZnO film with zinc nitrate hydrate (ZnO (N)) was found to have an amorphous phase and much more oxygen vacancy ($V_o$) than Zn-O bonds. Despite no crystallinity, the ZnO (N) had conductance comparable to that of ZnO with zinc acetate dihydrate (ZnO (A)) annealed at $500^{\circ}C$ as in TFTs. These results show that sol-gel could be made a potent process for low-cost and flexible device applications by optimizing the precursors.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.15-18
• /
• 2012

Transparent conductive indium zinc oxide thin films were prepared by spin-coating a sol-gel solution. Zinc acetate dihydrate [$Zn(CH_3COO)_2{\cdot}2H_2O$] and indium acetate [In$(CH_3COO)_3$] were used as starting precursors, and 2-methoxyethanol with 1-propanol as solvents. Upon annealing in a temperature range from 500 to $1000^{\circ}C$, the thin film crystallizes into polycrystalline $In_2O_3$(ZnO). The lowest electrical resistivity was obtained at an annealing temperature of $700^{\circ}C$ as $2{\Omega}{\cdot}cm$. Average optical transmittances were higher than 80% at all annealing temperatures. These experimental results confirm that the sol-gel spin-coating can be a good simplified practical method for forming transparent electrodes.

• Korean Journal of Materials Research
• /
• v.33 no.12
• /
• pp.550-557
• /
• 2023

In zinc-air batteries, the gel polymer electrolyte (GPE) is an important factor for improving performance. The rigid physical properties of polyvinyl alcohol reduce ionic conductivity, which degrades the performance of the batteries. Zinc acetate is an effective additive that can increase ionic conductivity by weakening the bonding structure of polyvinyl alcohol. In this study, polymer electrolytes were prepared by mixing polyvinyl alcohol and zinc acetate dihydride. The material properties of the prepared polymer electrolytes were analyzed by Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Also, Electrochemical impedance spectroscopy was used to calculate ionic conductivity. The electrolyte resistances of GPE, 0.2 GPE, 0.4 GPE, and 0.6 GPE were 0.394, 0.338, 0.290, and 0.213 Ω, respectively. In addition, 0.6 GPE delivered 0.023 S/cm high ionic conductivity. Among all of the polymer electrolytes tested, 0.6 GPE showed enhanced cycle life performance and the highest specific discharge capacity of 11.73 mAh/cm² at 10 mA. These results verified that 0.6 GPE improves the performance of zinc-air batteries.

• Journal of the Korean Ceramic Society
• /
• v.42 no.4
• /
• pp.245-250
• /
• 2005

ZnO was deposited on sapphire single crystal substrate by an ultrasonic pyrolysis of Zinc Acetate Dehydrate (ZAH) with carrying Ar gas. Through Thermogravimetry-Differential Scanning Calorimetry(TG-DSC), zinc acetate dihydrate was identified to be dissolved into ZnO above $380^{\circ}C$. ZnO deposited at $380-700^{\circ}C$ showed polycrystalline structures with ZnO (101) and ZnO (002) diffraction peaks like bulk ZnO in XRD, and from which c-axis strain ${\Sigma}Z=0.2\%$ and compressive biaxial stress$\sigma=-0.907\;GPa$ was obtained for the ZnO deposited $400^{\circ}C$. Scanning electron microscope revealed that microstructures of the ZnO were dependent on the deposition temperature. ZnO grown below temperature $600^{\circ}C$ were aggregate consisting of zinc acetate and ZnO particles shaped with nanoblades. On the other hand the grain of the ZnO deposited at $700^{\circ}C$ showed a distorted hexagonal shape and was composed of many ultrafine ZnO powers of 10-25 nm in size. The formation of these ulrafine nm scale ZnO powers was explained by the model of random nucleation mechanism. The optical property of the ZnO was analyzed by the photoluminescence (PL) measurement.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.676-677
• /
• 2006

Synthesis of zinc oxide nanorods, sheets and flower like structure were done by the sol-gel method using zinc acetate dihydrate and sodium hydroxide at $80^{\circ}C$ with 12 hours refluxing time nanorods, in case of as synthesized powder, with diameter of 20-60nm. Annealing at higher temperature (300 and $500^{\circ}C$,) in air ambient changes the morphology to sheet and flower like structure. The standard peak of zinc oxide was observed in IR at $523cm^{-1}$. The UV-VIS spectroscopy of zinc oxide shows a characteristic peak at 375nm.

• Korean Chemical Engineering Research
• /
• v.61 no.2
• /
• pp.322-327
• /
• 2023

A design of experiments was evaluated in optimizing MOF-5 synthesis for acetylene adsorption. At first, mixture design was used to optimize precursor concentration, terephthalic acid, zinc acetate dihydrate and N,N-dimethylformamide. More specifically, 13 conditions with various molar ratios were designed by extreme vertices design method. After preparing the samples, XRD, N₂ physisorption and SEM analysis were performed for their characterization. Moreover, acetylene adsorption experiments were carried out over the samples under identical conditions. The optimal precursor composition for MOF-5 synthesis was predicted on a molar basis as follows: terephthalic acid : acetate dihydrate : dimethylformamide = 0.1 : 0.4 : 0.5. Thereafter, multi-level factorial design was designated to investigate the effect of synthesis reaction conditions such as temperature, time and stirring speed. By the statistical analysis of 18 samples designed, 4 reaction parameters were determined for additional adsorption experiments. Therefore, MOF-5 prepared under the synthesis time and temperature of 100 ℃ and 12 h, respectively, showed the maximum adsorption capacity of 15.1 mmol/g.

• Applied Chemistry for Engineering
• /
• v.33 no.4
• /
• pp.402-407
• /
• 2022

Statistical design of experiments was used to optimize the MOF-5 synthesis process. A mixture design was employed to optimize precursor concentration. The optimal composition of three chemical materials, terephthalic acid, zinc acetate dihydrate, and N,N-dimethylformamide for MOF-5 synthesis was determined by extreme vertices design methods as follows; 1 mol : 2.7 mol : 40 mol. A multilevel factorial design was selected to screen the significance of synthesis reaction conditions such as temperature, time, and stirring speed. Statistical analysis results suggested excluding stirring speed from further investigation. Using a central composition design, the synthesis time and temperature were optimized. The quadratic model equation was derived from 13 synthesis experiments. The model predicted that MOF-5 synthesized at 119 ℃ for 10.4 h had the highest crystallinity.

• Journal of the Korean Chemical Society
• /
• v.60 no.1
• /
• pp.34-38
• /
• 2016

In this paper, zinc oxide nanoparticles (ZnO NPs) were synthesized using the sonochemical method, where equimolar amounts of zinc acetate dehydrate and sodium hydroxide were separately dissolved in deionized water, and then mixed for 30 min under magnetic stirring. The resultant white gel was sonicated for 60, 120, 180, 240, and 360 min with magnetic stirring. The obtained precipitates were centrifuged, repeatedly washed with ethanol to remove ionic impurities, and dried at 50 ℃ for 24 h. The formation of pure NPs was confirmed by X-ray diffraction, and their crystallinity and crystal phases were analyzed as well. Structural investigation was carried out by field-emission scanning electron microscopy (FE-SEM). The photocatalysis behavior of the ZnO NPs was investigated in a dark room under UV irradiation, using Rhodamine B. Spherical, rod, and flower-like ZnO NPs could be obtained by adjusting the sonication time, as observed by FE-SEM. The flower-like ZnO NPs exhibited excellent photocatalytic activity.

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.350-356
• /
• 2015

The effects of the zinc oxide (ZnO) preparing process on the performance of inverted organic photovoltaic cells (OPVs) were explored. The morphology and size of ZnO nanoparticles were controlled, leading to more efficient charge collection from device and higher electron mobility compared with nanospheres. Nanosized ZnO particles were synthesized by using zinc acetate dihydrate and potassium hydroxide in methanol. Also, water was added into the reaction medium to control the morphology of ZnO nanocrystals from spherical particles to rods, and $NH_4OH$ was used to prevent the gelation of dispersion. Solution-processed ZnO thin films were deposited onto the ITO/glass substrate by using spin coating process and then ZnO films were used as an electron transport layer in inverted organic photovoltaic cells. The analyses were carried out by using TEM, FE-SEM, AFM, DLS, UV-Vis spectroscopy, current density-voltage characteristics and solar simulator.