• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4740-4744
• /
• 2012

The purpose of this paper was to make a LED light control module using Zigbee. The module was made so that brightness of the LED light changes according to the ambient brightness. A 8-bit microcontroller was used to implement the module to enable LED dimming and wireless light intensity measurement. Using the proposed method, power consumption can be improved by up to 48% on average, with 3.4-0.4W changes in power. The measured ambient light intensity values are converted from analog to digital and outputted as a PWM waveform. According to the output waveform and changes in the current outputted from the LED driver, the brightness of the LED light is controlled. Also, Zigbee with close-range wireless communication capabilities was used to enable wireless transmission of light intensity measurements.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.9
• /
• pp.825-833
• /
• 2016

This paper introduces a direct-conversion CMOS RF transmitter for the IEEE 802.15.4 standard with a low-power high-gain up-conversion mixer designed in $0.18{\mu}m$ process. The designed RF DCT(Direct Conversion Transmitter) is composed of differential DAC(Digital to Analog Converter), passive low-pass filter, quadrature active mixer and drive amplifier. The most important characteristic in designing RF DCT is to satisfy the 2.4 GHz Zigbee standard in low power. The quadrature active mixer inside the proposed RF DCT provides enough high gain as well as sufficient linearity using a gain boosting technique. The measurement results for the proposed transmitter show very low power consumption of 7.8 mA, output power more than 0 dBm and ACPR (Adjacent Channel Power Ratio) of -30 dBc.

• Journal of Korea Society of Industrial Information Systems
• /
• v.17 no.4
• /
• pp.1-7
• /
• 2012

This paper proposes a new indoor location recognition system using a ZigBee network and a global positioning system(GPS). The proposed location recognition system applies GPS values that are mainly used for outdoor location recognition, to indoor location recognition; hence the techniques conventionally separated for the indoor and outdoor location recognition are integrated into one location recognition technique. The proposed system recognizes a location using the distance between nodes. Although the distance between nodes can be calculated by measuring the strength of the received ZigBee signals, generally the measured distance is not accurate and has high error rates since the strength of the ZigBee signals is different depending on the distance. In order to reduce the error rate, we have subdivided the output power of the received ZigBee signals into five levels. When a moving node generates a signal, each fixed node transmits the received signal strength and its own GPS information to other nodes, so the moving node can find its own accurate location in terms of the received signals.

• Journal of Advanced Information Technology and Convergence
• /
• v.9 no.2
• /
• pp.75-87
• /
• 2019

This paper presents a fully digital controlled power supply unit for the wireless controlled dimmable LED lighting system. The proposed power supply designed using a fly-back converter, which is directly controlled by a microprocessor. Although the proposed circuit does not sense the AC input current and has not AC input voltage feed-forward, it can achieve a high power factor. The proposed power supply directly regulates the output power for LED loads using the PWM and PFM control of the fly-back converter without additional regulator. For a wireless remote control function, the Zigbee modem is equipped in the proposed power supply. A prototype set-up has been built and tested. Through the experiment with a prototype set-up, the usefulness of the proposed power supply is verified.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.64 no.2
• /
• pp.50-56
• /
• 2015

This paper presents a smart monitoring technique for photovoltaic power systems by using wire and wireless communication networks in which the RS-232/484 and the Zigbee communication networks are inherently established respectively. In the proposed monitoring systems, environmental data sequences and the output power measured by sensors in photovoltaic systems are transferred to PC systems via two communication networks. We made electronic hardware boards for sensors and communication networks to construct its real-time monitoring system and carry out experiments for demonstrating reliability of the proposed monitoring system.

• 한국정보통신설비학회:학술대회논문집
• /
• 2009.08a
• /
• pp.162-164
• /
• 2009

IEEE 802.15.4에서 채널 간 충돌을 회피하기 위해 제안된 CSMA/CA 알고리듬은 수신되는 신호의 상관관계를 나타내는 지표인 LQI (Link Quality Indicator) 값과 수신되는 신호의 크기를 나타내는 지표인 RSSI (Received Signal Strength Indicator) 값을 이용한다. 지그비 모듈에서 측정되는 LQI 값은 수신되는 신호의 크기에 따라 변화하는데, 그 상관관계가 매우 부정확한 문제가 있어 왔다. 본 논문에서는 CC2430과 CC2591을 이용해 제작된 지그비 모듈을 기반으로 수신 신호의 크기와 LQI 값을 실험적으로 측정하여 RSSI 값에 따른 LQI 값의 상관관계를 분석하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.15 no.2
• /
• pp.339-346
• /
• 2011

In the existing RF communication based WPAN environment, a lowering of battery span and interference problem among sensors occur because the value of output is set and transmitted steadily when the system on sensor is initialized. Therefore, this paper proposes a framework and a transmit method with low power which decreases the electricity consumption by properly controling transmit power of opponent by received signal strength indicator(RSSI) of each sensor. The system proposes a power-lowering method by controling transmit power properly by the transmit intensity of the connected sensor after being affected by the transmit intensity of surrounded sensor. The framework that is proposed in this paper includes data transmit module, transmit power manager module, transmit power searching module, signal transmit module, and signal receiving module.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.6
• /
• pp.123-132
• /
• 2012

Gas sensors has been used very differently that depending on following purposes; Automotive (exhaust gas, fuel mixture gas, oxygen, particulates), agriculture / food industry (fresh, stored, CO2, humidity, NH3, nitrogen oxide gas, organic gas, toxic gas emitted from pesticides and insecticides), industrial / medical (chemical gas, hydrogen, oxygen and toxic gases), military (chemical weapon), environmental measurements (CO and other air pollution consisting of sulfur and nitrogen gas), residential (LNG, LPG, butane, indoor air, humidity). The types of industrial toxic substances are known about 700 species and many of these exist in gaseous form under normal conditions. he multi-gas detection sensors will be developed for casualties that detect the most important and find easy three kinds of gases in marine plant; carbon dioxide(CO2), carbon(CO), ammonia(NH3). Package block consists of gas sensing device minor ingredient, rf front end, zigbee chip. Develope interworking technology between the sensor and zigbee chip inside a package. Conduct a performance test through test jig about prototype zigbee sensor module with rf output power and unwanted emission test. This research task available early address when poisonous gas leaked from large industrial site and contribution for workers' safety at the enclosed space.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.7
• /
• pp.629-634
• /
• 2016

This paper describes the implementation of a ZigBee sensor node that can be utilized as a multiband and machine to machine (M2M) communication gateway. The IEEE 802.15.4-2003 standard was used as the wireless network frequency band. Ember's Type EM357 SoC was used as the transmission and reception device to perform the communication function, and it was also used for both the main M2M gateway and the sensor node. For the implementation of the operating protocol, EmberZNet Stack 4.5.4 from the Ember Corporation was used. The measurement of the reception sensitivity in the receiving module and the actual output signal from the reference were obtained from the transmission of a packet, and the packet included the M2M gateway within the attached ZigBee sensor. The packet error rate was measured as 0% with a -98 dBm reception sensitivity at the ZigBee frequency. In addition, excellent current characteristics of the ZigBee modules were shown by the implementation of the low-power circuit.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.327-332
• /
• 2017

As Internet of Things (IoT) technology advances, there is a growing demand for location-based services (LBSs) to identify users' mobility and identity. The initial LBS system was mainly used to measure position information by measuring the phase of a signal transmitted from a global positioning system (GPS) satellite or by measuring distance to a satellite by tracking the code of a carrier signal. However, the use of GPS satellites is ineffective, because it is difficult to receive satellite signals indoors. Therefore, research on wireless communications systems like ultra-wide band (UWB), radio frequency identification (RFID), and ZigBee are being actively pursued for location recognition technology that can be utilized in an indoor environment. In this paper, we propose an LBS system that includes the 2.45GHz band for chirp spread spectrum (CSS), and the 3.1-10.6GHz band and the 250-750MHz bands for UWB using the IEEE 802.15.4a standard for low power-based location recognition. As a result, we confirmed that the 2.45GHz Industrial, Scientific and Medical (ISM) band RF transceiver and the ranging function can be realized in the hardware and has 0dBm output power.