• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.8
• /
• pp.16-21
• /
• 2012

The gyro sensor that made by MEMS process is generated an accumulated error(drift) and escape the zero angle following during calculation of rotate angle. This study propose BACF(Boot Angle Compensation Filter) algorithm for prevent escape zero angle and DCF algorithm for remove accumulated error. DCF algorithm is designed for acquire accurate turn of ratio by remove offset and noise components. BACF algorithm is obtained average offset that removed noise components by recursively calculate. Experimental environment, two-axis gyro sensor and mobile OIS camera mounted control board and 5Hz oscillation of ${\pm}0.5^{\circ}$ for the experiments were carried out. BACF and DCF algorithm is applied and the resulting accumulated error did not occur and exactly zero angle following results were made.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.4
• /
• pp.143-148
• /
• 2020

In the case of a system that detects and controls the phase of an alternating voltage, the analog control method compensates the phase offset part by filtering for the detected phase and applies it to the control. However, in the digital control method, precise control cannot be achieved due to an error between the operating frequency of the microprocessor or the microcontroller and the input phase time when controlled using such phase detection. In general, when the method used is a certain time, the accumulated error is compensated and adjusted at random. To solve this problem, a method of detecting a zero point in real time and compensating for the operating frequency of the microprocessor is needed. Therefore, the research to be performed in this paper to reduce these errors and apply them to precise digital control is as follows. 1) Research on how to implement Zero Crossing Detection algorithm through simulation modeling to compensate the zero point to match the operating frequency through detection. 2) A study on the method of detecting zero points in real time through the Zero Crossing Detection design using a microcontroller and compensating for the operating frequency of the microprocessor. 3) A study on the estimation of the rotor position of BLDC motors using the Zero Crossing Detection circuit.

• Journal of Korean Society for Atmospheric Environment
• /
• v.27 no.2
• /
• pp.133-141
• /
• 2011

In this study, different calibration approaches for reduced sulfur compounds (RSCs) were investigated by using thermal desorption coupled with gas chromatography (GC) and pulsed flame photometric detection (PFPD). To evaluate the effects of calibration procedures, gaseous standards of 4 RSCs ($H_2S$, $CH_3SH$, DMS, and DMDS) prepared at 10 ppm level were analyzed at 7 loading injection volumes (40, 60, 80, 100, 160, 240, and 320 ${\mu}L$). The results were then compared with calibration curves made with the Z (zero offset) and N (non-zero offset) method. The concentrations of unknown samples were then quantified by using R (ratio) method in which the slope values are compared between standards and samples. Secondly, in A (average) method, results obtained from a multi-point analysis of unknown samples were also averaged to extract representative values for each sample. Results of both experiments showed that analytical error of low molecular weight components (such as $H_2S$ and $CH_3SH$) was greatly expanded with the Z method. In conclusion, the combined application of N-A method was the more realistic approach to reduce biases in the quantification of RSCs.

• Economic and Environmental Geology
• /
• v.32 no.5
• /
• pp.495-502
• /
• 1999

Common-mid-point (CMP) seismic data on a dipping layer have have a stacking different from a horizontal layer velocity and the reflection points on data are dispersed to many positions. Therefore, the CMP data are not stacked well by the conventional stacking method using the horizontal layer velocity. The CMP gather can ideally stacked by applying dip-moveout(DMO) processing. Hence, modern seismic processing indludes DMO as an essential routine step. DMO processing techniques are broadly categorized by two, Fourier transform and integral methods, each of which has many different computational schemes. In this study, the dip-decomposition technique of the Fourier transform method is used to test the DMO effect on the synthetic scismic data generated for dipping structures. Each of constnat offset sections NMO corrected by using the layer velocity of the model and DMO processed. The resulting zero-offset sections for many offsets are stacked. The stacked sections with DMO processing show the structural boundaries of the models much better than those without DMO processing.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.10
• /
• pp.542-549
• /
• 2004

The conventional fault location algorithms based on the travelling waves have an inherent problem. In cases of the close-up faults occurring near the relaying point and of the faults having zero degree inception angle of voltage signals, the conventional algorithms can not estimate an accurate fault distance. It is because the shapes of travelling waves are near sinusoidal in those cases. A new method solving this problem is presented in this paper. An FIR(Finite Impulse response) filter which makes high frequency components prominent and makes the power frequency component and dc-offset attenuated is used. With this method, the cross-correlation peak is to be very clear when a close-up fault or a fault having near zero-degree inception angle occurs. The cross-correlation peaks can be clearly distinguished and accurate fault location is practically possible consequently. A series of simulation studies using EMTP(Electromagnetic Transients Program) show that the proposed algorithm can calculate an accurate fault distance having maximum 2% or less error.

• Journal of Power Electronics
• /
• v.16 no.6
• /
• pp.2109-2118
• /
• 2016

Based on the space vector pulse width modulation (SVPWM) theory, this paper realizes an easier SVPWM strategy, which is equivalently implemented by CBSPWM with zero-sequence voltage injection. The traditional SVPWM strategy has no effect on controlling the neutral-point voltage balance. In order to solve the neutral-point voltage unbalance problem for neutral-point-clamped (NPC) three-level inverters, this paper proposes a neutral-point voltage balance controller. The proposed controller realizes controlling the neutral-point voltage balance by dynamically calculating the offset superimposed to the three-phase modulation waves of an equivalent SVPWM strategy. Compared with the traditional SVPWM strategy, the proposed neutral-point voltage balance controller has a strong ability to balance the neutral-point voltage, has good steady-state performance, improves the output waveforms quality and is easy for digital implementation. An experiment has been carried out on a NPC three-level inverter prototype based on a digital signal processor-complex programmable logic device (DSP-CPLD). The obtained experimental results verify the effectiveness of the proposed neutral-point voltage balance controller.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.10C
• /
• pp.1032-1041
• /
• 2007

The global navigation satellite system (GNSS), which is the core technique for the location based service, adopts the direct sequence/spread spectrum (DS/SS) as its modulation method. The success of a DS/SS system depends on the synchronization between the received and locally generated pseudo noise (PN) signals. As a step in the synchronization process, the tacking scheme performs fine adjustment to bring the phase difference between the two PN signals to zero. The most widely used tracking scheme is the delay locked loop with early minus late discriminator (EL-DLL). In the ideal case, the EL-DLL is the best estimator among various DLL. However, in the band-limited multipath environment, the EL-DLL has tracking bias. In this paper, the timing offset range of correlation function is divided into advanced offset range (AOR) and delayed offset range (DOR) centering around the correct synchronization time point. The tracking bias results from the following two reasons: symmetry distortion between correlation values in AOR and DOR, and mismatch between the time point corresponding to the maximum correlation value and the synchronization time point. The former and latter are named as the type I and type II tracking bias, respectively. In this paper, when the receiver has finite bandwidth in the presence of multipath signals, it is shown that the type II tracking bias becomes a more dominant error factor than the type I tracking bias, and the correlation values in AOR are not almost changed. Exploiting these characteristics, we propose a novel tracking bias mitigation scheme and demonstrate that the tracking accuracy of the proposed scheme is higher than that of the conventional scheme, both in the presence and absence of noise.

• Journal of The Korean Astronomical Society
• /
• v.55 no.2
• /
• pp.37-57
• /
• 2022

Using I-band images of 35 nearby (z < 0.1) type 1 active galactic nuclei (AGNs) obtained with Hubble Space Telescope, selected from the 70-month Swift-BAT X-ray source catalog, we investigate the photometric properties of the host galaxies. With a careful treatment of the point-spread function (PSF) model and imaging decomposition, we robustly measure the I-band brightness and the effective radius of bulges in our sample. Along with black hole (BH) mass estimates from single-epoch spectroscopic data, we present the relation between BH mass and I-band bulge luminosity (M_BH-M_I,bul relation) of our sample AGNs. We find that our sample lies offset from the M_BH-M_I,bul relation of inactive galaxies by 0.4 dex, i.e., at a given bulge luminosity, the BH mass of our sample is systematically smaller than that of inactive galaxies. We also demonstrate that the zero point offset in the M_BH-M_I,bul relation with respect to inactive galaxies is correlated with the Eddington ratio. Based on the Kormendy relation, we find that the mean surface brightness of ellipticals and classical bulges in our sample is comparable to that of normal galaxies, revealing that bulge brightness is not enhanced in our sample. As a result, we conclude that the deviation in the M_BH-M_I,bul relation from inactive galaxies is possibly because the scaling factor in the virial BH mass estimator depends on the Eddington ratio.

• Economic and Environmental Geology
• /
• v.23 no.3
• /
• pp.353-358
• /
• 1990

This paper presents numerical experiments on migration of synthetic seismograms using by $45^{\circ}$ wave equation. The seismograms used are zero-offset seismogram (corresponding to stacked section) on point reflectors, dipping plane reflector, faulted and folded layers. The seismograms are constructed by upward continuation of seismic source wavelets, exploading on subsurface reflection interfaces, to the earth surface. The synthetic seismograms are migrated by downward continuation and imaging. The upward and downward continuations are implemented by solving the $45^{\circ}$ wave equation with the finite-difference method. Migration of the synthetic data used in this study results in relatively accurate reposition of subsurface structures while the synthetic sections are quite different from the structures.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.1
• /
• pp.80-83
• /
• 2022

This paper proposes an initial rotor polarity detection algorithm of a single-phase permanent magnet synchronous motor (SP-PMSM) related to stable open-loop starting for sensorless operation. Generally, the SP-PMSM needs an asymmetric air-gap structure to can avoid the initial starting failure at zero torque point. Therefore, the rotor polarity information can be obtained by using the DC offset current direction of a stator current through a high frequency voltage injection into an SP-PMSM with an asymmetric air gap. In this paper, the proposed rotor initial polarity detection algorithm is verified through several experimental results.