• Journal of Korean Society of Forest Science
• /
• v.94 no.6
• /
• pp.468-475
• /
• 2005

To understand spatiotemporal changes of temperature and humidity in Lentimula edodes cultivation sheds, temperature, relative humidity were measured with HOBO H8 series sensors in log cultivation sheds and sawdust cultivation sheds. The results obtained from October in 2003 to October in 2004 were as follows; 1. Horizontal temperature changes were smaller at center of cultivation shed inside than comer of cultivation shed inside, while relative humidity changes were greater about 3% at center of cultivation shed inside than corner of cultivation shed inside. 2. Vertical temperature changes showed that the temperature was higher at above than at below when the temperature rises, while the temperature was lower at above than at below when the temperature falls. Thus close to soil surface temperature showed a little fluctuation. Vertical relative humidity changes showed that the relative humidity was lower at above than at below when the temperature rises, while the relative humidity was higher at above than at below when the temperature falls. After all temperature and relative humidity was the opposite in cultivation shed. 3. It's showed in log cultivation shed that the minimum temperature was a subzero temperature until the end of April, while the minimum temperature did above zero after the beginning of the May. Besides a winter was the greatest at daily temperature range during the four season, about $30^{\circ}C$. On the other hand the minimum relative humidity was less than 20% at April, May and June but more than 40% after May.

• Journal of Korean Society of Forest Science
• /
• v.32 no.1
• /
• pp.9-15
• /
• 1976

Financial rotations of Pinus koraiensis stands are calculated and compared on the basis of five basic financial maturity concepts. The rotations given by the forest rent and average annual gross revenue models are in excess of sixty years by adopting zero interest rates of capital and forest lands. IRR model also neglects land value and highly sensitive to the changes of fixed and regeneration costs. The Faustmann doctrine recommands rotation ages of 23-39 years depend upon applied interest rates and site indices, and seems to be most adequate for determining financial maturity. It is however the situation in Korea that economic conditions are changing rapidly, and thus a model which does not require many exogenous variables in calculation process is preferable. The Duerr's solution has a basic simplicity and logic which is appealing from both a theoritical and practical viewpoint, and most adaptable to the Korean situation, even though the model completly neglects the opportunity cost for forest land. There is a tendency to reduce rotation length with the increase of site quality, but the difference is negligible.

• Journal of the Korean Geographical Society
• /
• v.50 no.4
• /
• pp.375-391
• /
• 2015

Trees to arrest sand-shifting have been planted on most of coastal dunes in Korea and considered as conservative objects. However, we reconsider that the simplicity of these trees have hindered ecological roles of coastal dunes; geochemical cycle and habitats of endemic species in coastal ecosystem. We examined geochemical properties of sediments on Byunsuran dune field where is planted with pine trees. There are significant difference in properties between embryo dune sediments and foredune sediments, but there are not between foredune and secondary dune. There are no significant difference between pine forest sediments and mixed forest sediments. It is also not showed the difference between dune ridge sediments and swale sediments. Despite spatial diversity from appearance, geochemical properties are not linked with geomorphic and vegetational conditions because of dense planted trees on foredune. To recover natural properties of coastal dunes, we need to change the conservation scheme to increase geomorphic and ecological diversity.

• Journal of the Korean Geographical Society
• /
• v.48 no.6
• /
• pp.897-913
• /
• 2013

The main purpose of the paper is to examine the spatial characteristics of school choice through residential mobility by conducting a correlation analysis on the relationships between the middle schools' entrance rates to special high schools and the elementary schools' net transfer rates. Analyses are done at both the individual school level and the school catchment area level. Prior to the calculation, the two variables involved in the correlation analysis are transformed via a standardization equation, and the standardized scores are mapped and explored. Both the global and local correlation analyses are done for the standardized variables. Main findings are twofold. First, the global correlation analysis reports that there exists a statistically significant correlation between the two variables at both the analytical levels. Second, albeit the prominent positive correlation at the global level, the local analysis reveals the existence of a considerable level of spatial heterogeneity in terms of bivariate association. While several school catchment areas with very high local correlation coefficients (the HH association type) are popped up, other areas with various types of bivariate association including ones even opposite to the global trend are also observed.

• Journal of the Korean Geotechnical Society
• /
• v.30 no.11
• /
• pp.51-60
• /
• 2014

Load and Resistance Factor Design (LRFD) is one of the limit state design methods, and has been used worldwide, especially in North America. Also, the study for LRFD has been actively conducted in Korea. However, the data for LRFD in Korea were not sufficient, so resistance factors suggested by AASTTO have been used for the design in Korea. But the resistance factors suggested by AASHTO represent the characteristics of bedrocks defined in the US, therefore, it is necessary to determine the resistance factors for designs in Korea, which can reflect the characteristics of bedrocks in Korea. Also, the calculated probabilities of failure from conventional reliability analyses which commonly use log-normal distribution are not realistic because of the lower tail that can be extended to zero. Therefore, it is necessary to calibrate the resistance factors considering the lower-bound resistance. Thus, this study calculates the resistance factors using thirteen sets of drilled shaft load test results, and then calibrates the resistance factors considering the lower-bound resistance corresponding to a target reliability index of 3.0. As a result, resistance factors from conventional reliability analyses were determined in the range of 0.13-0.32 for the shaft resistance, and 0.19-0.29 for the base resistance, respectively. Also, the lower bounds of resistance were determined based on the Hoek-Brown failure criteria (2002) and GSI downgrading. Considering the lower-bound resistances, resistance factors increased by 0~8% for the shaft, and 0~13% for the base, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.1
• /
• pp.73-79
• /
• 2013

Crystalline silicon solar cells with $SiN_x/SiN_x$ and $SiN_x/SiO_x$ double layer anti-reflection coatings(ARC) were studied in this paper. Optimizing passivation effect and optical properties of $SiN_x$ and $SiO_x$ layer deposited by PECVD was performed prior to double layer application. When the refractive index (n) of silicon nitride was varied in range of 1.9~2.3, silicon wafer deposited with silicon nitride layer of 80 nm thickness and n= 2.2 showed the effective lifetime of $1,370{\mu}m$. Silicon nitride with n= 1.9 had the smallest extinction coefficient among these conditions. Silicon oxide layer with 110 nm thickness and n= 1.46 showed the extinction coefficient spectrum near to zero in the 300~1,100 nm region, similar to silicon nitride with n= 1.9. Thus silicon nitride with n= 1.9 and silicon oxide with n= 1.46 would be proper as the upper ARC layer with low extinction coefficient, and silicon nitride with n=2.2 as the lower layer with good passivation effect. As a result, the double layer AR coated silicon wafer showed lower surface reflection and so more light absorption, compared with $SiN_x$ single layer. With the completed solar cell with $SiN_x/SiN_x$ of n= 2.2/1.9 and $SiN_x/SiO_x$ of n= 2.2/1.46, the electrical characteristics was improved as ${\Delta}V_{oc}$= 3.7 mV, ${\Delta}_{sc}=0.11mA/cm^2$ and ${\Delta}V_{oc}$=5.2 mV, ${\Delta}J_{sc}=0.23mA/cm^2$, respectively. It led to the efficiency improvement as 0.1% and 0.23%.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.8 no.6
• /
• pp.460-469
• /
• 2015

This study's aim is for reducing big data transfer time of IoT healthcare devices by modulating digital bits into Manchester code including zero-voltage idle as information for secondary compressed binary cluster's compartment after two step compression of compressing binary data into primary and secondary binary compressed clusters for each binary clusters having compression benefit of 1 bit or 2 bits. Also this study proposed that as department information of compressed binary clusters, inserting idle signal into Manchester code will have benefit of reducing transfer time in case of compressing binary cluster into secondary compressed binary cluster by 2 bits, because in spite of cost of 1 clock idle, another 1 bit benefit can play a role of reducing 1 clock transfer time. Idle signal is also never consecutive because the signal is for compartment information between two adjacent secondary compressed binary cluster. Voltage transition on basic rule of Manchester code is remaining while inserting idle signal, so DC balance can be guaranteed. This study's simulation result said that even compressed binary data by another compression algorithms could be transferred faster by as much as about 12.6 percents if using this method.

• The KIPS Transactions:PartA
• /
• v.16A no.4
• /
• pp.263-272
• /
• 2009

For implementing the ubiquitous computing environments with smart home infrastructures, various research on the home network have been performed by several research institutes and companies. Due to the various home network middleware that are developed recently, the standardization of the home network middleware is being delayed and it calls for the middleware bridge which solves the interoperability problem among the heterogeneous middlewares. Now the research on the scheme for interoperability and the development of the various bridges are in progress, such as one-to-one bridge supporting interoperability between two middlewares and one-to-many bridge supporting interoperability among the multi-middlewares. However, existing systems and schemes does not consider the dynamic extensibility and performance that is particularly needed in the smart home environments. The middleware bridge should provide bridge extensibility with zero-configuration for non-expert users. It should also provide the load balancing scheme for efficient and proper traffic distribution. In this paper, we propose a Multi-Middleware Bridge(MMB) for dynamic extensibility and load balancing in home network environments. MMB provides bridge scalability and load balancing through the distributed system structure. We also verify the features such as interoperability, bridge extensibility, and the performance of the load balancing algorithm.

• The KIPS Transactions:PartD
• /
• v.15D no.6
• /
• pp.861-872
• /
• 2008

As rapid development of computing environment, field of automatic identification research which interoperates with various physical objects and digital information is making active progress. Although the automatic identification system is widely used in various industries, application of automatic identification system in the field of medical health doesn't reach other industry. Therefore research in medical health supplies such as medical equipment, blood, human tissues and etc is on progress. This paper suggests the application of automatic identification technology for biological resources which is core research material in human genome research. First of all, user environment requirements for the introduction of automatic identification technology are defined and through the experiments and research, barcode is selected as a suitable tag interface. Data Matrix which is 2D barcode symbology is chosen and data schema is designed based on UCC/EAN-128 for international defecto standard. To showapplicability of proposed method when applied to actual environment, we developed, tested and evaluated application as following methods. Experiments of barcode read time at 196 and 75 below zero which is actual temperature where biological resources are preserved resulted read speed of average of 1.6 second and the data schema satisfies requirements for the biological resources application. Therefore suggested method can provide data reliability as well as rapid input of data in biological resources information processing.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.4A
• /
• pp.336-344
• /
• 2005

Discrete Wavelet Transform(DWT) is the oncoming generation of compression technique that has been selected for MPEG4 and JEPG2000, because it has no blocking effects and efficiently determines frequency property of temporary time. In this paper, we propose an efficient bit-serial architecture for the low-power and low-complexity DWT filter, employing two-channel QMF(Qudracture Mirror Filter) PR(Perfect Reconstruction) lattice filter. The filter consists of four lattices(filter length=8) and we determine the quantization bit for the coefficients by the fixed-length PSNR(peak-signal-to-noise ratio) analysis and propose the architecture of the bit-serial multiplier with the fixed coefficient. The CSD encoding for the coefficients is adopted to minimize the number of non-zero bits, thus reduces the hardware complexity. The proposed folded 1D DWT architecture processes the other resolution levels during idle periods by decimations and its efficient scheduling is proposed. The proposed architecture requires only flip-flops and full-adders. The proposed architecture has been designed and verified by VerilogHDL and synthesized by Synopsys Design Compiler with a Hynix 0.35$\mu$m STD cell library. The maximum operating frequency is 200MHz and the throughput is 175Mbps with 16 clock latencies.