• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2004년도 춘계학술대회 논문집
• /
• pp.502-505
• /
• 2004

The purpose of this experiment is to modify diagnosis criterion of isothermal relaxation current(IRC) measurement equipment which is using for distribution cable diagnosis. We're using this system for several years in the field instead of DC leakage current measurement and lots of cables were replaced. But we have to investigate on the reliability of this equipment for our cables because we didn't carried out condition assessment of extracted cables after field diagnosis by this equipment. It is important thing for cable maintenance. If the replacement criterion is improper we can not prevent failures or will waste budget on account of replacement of the sound cables. In this papar we selected field installed cables and injected silicone fluid to the cables for insulation rehabilitation. In order to prove reliability of the diagnosis equipment we compared diagnosis results and AC breakdown strength according to operating time after silicone treatment. This is the results of the field test for 1 year.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 2006년도 International Symposium on GPS/GNSS Vol.2
• /
• pp.541-546
• /
• 2006

Zigbee를 이용한 실내 위치 측정 기법에서는 수신신호세기(RSSI) 측정치를 거리측정치로 활용하여 삼각측량법이나 DB 검색법을 이용하여 위치를 구한다. RSSI 측정치는 Zigbee 통신에서 기본적으로 제공하는 값으로 하드웨어 추가 없이 거리 측정에 사용할 수 있지만 정확도가 떨어진다. 이를 해결하기 위해 초음파 센서를 장착하고 RF와 초음파의 속도차이를 이용하여 정확한 거리를 측정할 수 있다. 이렇게 구해진 거리를 이용하면 정확한 위치를 구할 수 있다. 이를 구현하는 방법으로 본 논문에서는 고정된 위치의 비컨들이 순차적으로 신호를 전송하여 노드의 위치를 구하는 경우 발생하는 비컨의 전송 스케줄, 추가 및 동기 유지의 어려움을 해결할 수 있도록 노드에서 신호를 전송하고 비컨에서 구한 거리를 다시 노드로 Zigbee 통신을 이용하여 전달하여 위치를 구하는 기법을 제시하였다. 추가로 본 논문에서는 비컨 수의 제약으로 위치를 구할 수 없는 경우에 초음파 측정치에 추가하여 RSSI 측정치를 동시에 이용하는 위치측정기법을 제시하고, 실제 정적, 동적 실험을 통하여 그 유용성을 보였다. 3개 이상의 초음파 신호가 수신되는 경우 cm 급의 정확도로 위치를 10Hz 이상으로 구할 수 있었으며, 2개 이하의 초음파 신호가 수신되는 경우에도 RSSI 측정치가 있으면 수십 cm 급의 정확도로 위치를 구할 수 있음을 확인하였다.

• 대한전기학회논문지:전력기술부문A
• /
• 제51권1호
• /
• pp.23-28
• /
• 2002

In order to survey the radiation characteristics of pure line noise of unwanted noise from overhead high voltage AC transmission lines, a disk type gap noise generator was manufactured. Disk size which decides capacitance between the noise generator and earth was selected through preliminary indoor experiments and analysis by using surface charge method. The capacitance is one of principal parameters related to the injection of a proper noise current into lines. On the basis of the capacitance obtained from calculation, 5mm of space was given to the gap of the noise generator to be installed o test line and an aluminum disk of 60cm radius was made. The field experiments were performed with the noise generator hung on the Kochang 765 kV full scale test line. As the results, the useful data which can be used to analysis the radiation characteristics of noise from transmission lines were obtained. Those are the directivity of antenna toward the line, lateral profiles, frequency spectra, height pattern and so on.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2002년도 춘계학술발표논문집 (하)
• /
• pp.1381-1384
• /
• 2002

최근 인터넷 서비스는 최선형 서비스 제공 위주에서 실시간 멀티미디어 서비스들의 QoS 보장을 함께 지원하는 차등화된 서비스 형태로 발전하고 있다. 또한, 기존의 SONET/SDH 전송망에서 다중 기가비트 파장을 제공하는 WDM 기술이 차세대 인터넷의 중심 기술로 부상하고 있다. WDM 백본망은 Ingress와 Egress 쌍 간에 여러 lightpath를 제공하므로 각각의 광 품질에 따라 각기 다른 광 경로를 설정하여 차등화된 광 서비스를 제공할 수 있으나, 현재의 WDM 백본망은 종단간 QoS 서비스 보장을 위한 어떠한 지원도 제공하지 못하고 있는 실정이다. 본 논문에서는 다양한 실시간 멀티미디어 서비스들을 IP over WDM 백본망에 적용하기 위해, 파장을 레이블로 사용하여 QoS 제공 기능과 트래픽 분산 기능을 용이하게 수행하는 GMPLS 기술을 차등화 서비스 기술과 같이 접목하여 새로운 형태의 차등화된 광 QoS 서비스(DOS) 제공 방안을 기술 한다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.1
• /
• pp.336-339
• /
• 2004

근래에 $TiO_2$를 이용한 염료감응형 태양전지에 대한 연구가 많이 진행되어 이미 실용화 단계에 이르고 있다. 그러나, 이러한 $TiO_2$를 이용한 태양전지 효율이 한계에 이르러 이를 향상시키기 위한 노력이 다방면에서 이루어지고 있다. 이에 본 연구에서는 넓은 밴드갭 직접형 반도체재료로서, 전기적, 열적, 광학적, 촉매 특성이 우수하고, 압전성이 크고 광투과성 및 형광성이 매우 우수하여, 현재 여러 전자사업 분야에서 사용될 뿐아니라, 태양전지분야에서도 최근 관심이 증대되고 있는, ZnO를 이용하여 $TiO_2$ 대체 전극재로서의 가능성을 고찰하였다. ZnO 슬러리는 유계 방법을 이용하여 제조하였고, 막은 닥터 블레이드(doctor blade)법에 의해 TCO 위에 형성되었다. 원료 분말 및 막의 형상은 FE-SEM에 의해 확인되었다. 형성된 막은 다양한 조건에서 소결하여, 최종적으로 샌드위치형 염료감응형 셀을 제조한 후 효율을 측정 비교하여 태양전지의 활성 전극 재료로서 적정한 ZnO 조건을 예측할 수 있었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.461-462
• /
• 2005

In order to improve the efficiency of dye-sensitized solar cell (DSC), $TiO_2$ electrode screen-printed on transparent conducting oxide (TCO) substrate was sintered in variation with different temperature(350 to $550^{\circ}C$). $TiO_2$ electrode on fluorine doped tin oxide (FTO) glass was assembled with Pt counter electrode on FTO glass. I-V properties of DSC were measured under solar simulator. Also, effect of sintering temperature on surface morphology of $TiO_2$ films was investigated to understand correlation between its surface morphology and sintering temperature. Such surface morphology was observed by atomic force microscopy (AFM). From the measurement results, at sintering temperature of $500^{\circ}C$, both efficiency and fill factor of DSC were mutually complementary, enhancing highest fill factor and efficiency. Consequently, it was considered that optimum sintering temperature of $\alpha$-terpinol included $TiO_2$ paste is at $500^{\circ}C$.

• Archives of Plastic Surgery
• /
• 제36권5호
• /
• pp.660-662
• /
• 2009

Purpose: There are several modalities to reattach the amputated auricle. Microvascular replantation can achieve the best outcome, but technically difficult. Conventional composite graft is technically easy, but uniformly unsuccessful. Our successful experience of reattachment using postauricular subcutaneous pocket is presented. Methods: The amputated tissue was placed in its anatomical position with buried sutures. The amputated part is dermabraded to remove the epidermis and outer layer of dermis(Fig. 1, Center, left). Postauricular skin flap was then raised and the reattached dermabraded ear was buried beneath the flap(Fig. 1, Center, right). Two weeks after the original surgery, the buried ear was removed from its pocket (Fig. 1, Below, left). Results: The ear was reepithelialized spontaneously in 7 days. At 3 months, the reattached ear has satisfactory appearance without contour deformity(Fig. 1, Below, right). Conclusion: This technique provides increase in contact surface between the amputated segment and the surrounding tissues which supply blood, serum, oxygen and nutrients, maximizing the probability of "take". Minimally injured dermis can be healed from spontaneous reepithelialization and provides minimal contour deformity. We have used this non-microsurgical technique with very satisfying outcome.

• 한국정밀공학회지
• /
• 제27권6호
• /
• pp.75-81
• /
• 2010

The purpose of this study was to investigate the short-term effects of electrical massager on stress-related parameters including heart rate variability (HRV), heart rate (HR) using the photoplethysmogram (PPG) signal with motion artifact correction. Twenty healthy subjects were randomly allocated to receive a 15-min section of three types ((1) resting mode (control group), (2) light massage mode, (3) strong massage mode). Results indicated that self-report, VAS (Visual Analog Scale) significantly decreased for two massage modes after massage except control group. In strong massage mode, it was associated with significant increases in HF, but significant decreases in LF and LH/HF ratio compared with the light massage mode. For all outcomes, similar changes were not observed in the control group. Also, the result founded that mean HR of all groups decrease. We conclude that electrical massager reduces perceived stress and improves adaptive autonomic response to stress in healthy adults.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.63-68
• /
• 2005

The nanoindentation technique is widely used to investigate the mechanical properties of nano-microscale materials. The nanoindentation method for assessing mechanical properties at low loads and shallow depths is already well established fur the characterization of thin films as well as bulk materials. In this study, we evaluated residual stress in DLC and Au thin films usign nanoindentation technique with a new stress-relaxation model. Moreover, We suggest a composite hardness equation and quantify the magnitude of hardness increase by using an equation based on the interface hardness and the interface thickness, derived by comparing results derived from this equation and those determined in nanoindentation tests. Finally, We present an indentation size effect (ISE) model that extends the available contact depth for ISE application down to several tens of nanometers by considering the tip bluntness effect.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2006년도 춘계학술대회
• /
• pp.154-157
• /
• 2006

The counter electrode widely used in DSCs (Dye-sensitized Solar Cells) is constructed of conducting glass substrates coated with Pt films, where the platium acts as a catalyst. Pt counter electrodes in DSCs are one important component. It is expected that characteristics of Pt electrodes strongly depend on fabrication process and its surface condition. In this study, Pt counter electrode surface of DSC is deposited by reactive RF magnetron sputtering under the conditions of Ar 5mtorr, RF power of 120w and substrate temperature of $100^{\circ}C$. Surface morphology of Pt electrodes was investigated by FE-SEM and AFM. And this paper shows our recent results and technology to fabricate the new designed cell with Pt electrodes deposited by sputtering method. We have achieved fill factor 65% and photoelectric conversion efficiency around 2.6% as the best results of new designed DSCs structure.