• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2009년도 추계학술대회 논문집
• /
• pp.25-26
• /
• 2009

• 한국광학회:학술대회논문집
• /
• 한국광학회 1988년도 광학 및 양자전자학 워크샵
• /
• pp.1-8
• /
• 1988

상용 가공용 Nd:YAG 레이저의 특성 및 제원 을 분석하고 설계 시 고려하여야 할 thermal lensing 효과의 영향에 따른 출력특성의 제한에 대하여 기술하였으며 이를 토대로 200W급의 Nd:YAG 레이저를 설계하였다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 1989년도 제4회 파동 및 레이저 학술발표회 4th Conference on Waves and lasers 논문집 - 한국광학회
• /
• pp.32-35
• /
• 1989

A 150W industrial Nd:YAG laser was developed. The thermal lensing effect was examined and the radius and position of rear mirror were optimized for higher efficiency. The efficiency of 2.5% was achieved. Also, the performance of laser welding in fine thermocouples and between high-temperature-melting dissimilar metals were investigated.

• 한국기계가공학회지
• /
• 제5권1호
• /
• pp.51-58
• /
• 2006

The objective of this research work is to investigate into heat transfer characteristics of the laser cutting of CSP 1N sheet using high power CW Nd:YAG laser. In order to investigate the heat transfer characteristics, three dimensional quasi stationary and steady-state heat transfer analysis has been carried out. The laser heat source is assumed as a volumetric heat source with a gaussian heat distribution in a plane. Through the comparison of the results of analyses with those of experiments, the proper finite element model has been obtained. In addition, characteristics of the three-dimensional heat transfer and temperature distribution have been estimated by the finite element model. Finally, the minimum temperature at the center for cutting of the material has been estimated.

• Journal of Welding and Joining
• /
• 제9권1호
• /
• pp.32-39
• /
• 1991

A 200W pulsed Nd: YAG laser for fine welding was developed. The important laser parameters such as laser peak power, average power, pulse width, and pulse energy for welding were studied. In order to obtain the sufficient laser power density for welding, thermal lensing effects were analyzed and a laser resonator with laser beam divergence was designed. The power supply unit was designed to support up to 7kW input. The pulse control unit was developed using a GTO thyristor and could control over 100kW input power to obtain 3.5kW peak power laser. Also due to the GTO thyristor the pulse width could be varied continuously from 0.1 to 20 msec and maximum repetition rate was as high as 300pps.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.125-128
• /
• 1995

The remote sleeve repair-welding technology using the pulsed Nd:YAG laser for increasing the lifetime of the steam generator tube in the nuclear power plant has been developed. The laser welding has many advantages on deep penetration depth and narrow heat affect zone(HAZ). The inconel 600 tube and inconel 690 sleeve used high temperature and high pressure service have been welded as round lap welds. It is found that the relation between the connection width and welding parameters. It is found that the shear strength in proportion to the connection width by conducting tensile-shear tests.

• 한국광학회지
• /
• 제14권5호
• /
• pp.515-520
• /
• 2003

수 KHz의 반복율로 발진하는 레이저광을 증폭하는 증폭기를 제작하고, 특성을 조사하였다. 증폭기로는 연속 방전하는 섬광등으로 펌핑되는 Nd:YAG 헤드를 사용하였고, 레이저 매질에서 발생하는 열 복굴절을 보상하여 이중통과 증폭기를 구성한 경우, 복굴절에 의한 레이저광 손실을 5%로 감소시켰다. 4 중통과 증폭기를 구성을 하였을 때, 반복율 5-10 KHz에서 이득은 약 3.2이었고, 펄스폭은 40 ns에서 48 ns로. 20%증가하였다.

• Journal of Welding and Joining
• /
• 제6권1호
• /
• pp.21-27
• /
• 1988

This paper describes weldability of dissimilar metal plates with YAG laser for the use of a small-size electronic spring parts. Effects of welding conditions, combination of plates, thickness of upper plate are examined in relation to welding strength and microstructure of welded region. The obtained results are summarized as follows. Welding defects such as cavity and crack showed a tendency to easily occur in the case where 1) pulse duration is short, 2) laser power is high, 3) PBS plate with high thermal diffusivity is used for lower plate. Among these defects, the occurrence of cavity cased a drop of welding strength. This results from the reduction of welding area between upper and lower plates. In SK-5/SUS304 plates (thickness: 0.2/0.4mm/, welding strength was the highest in welding conditions: laser power is 30J/pulse, pulse duration 9ms, amount of defocus +2mm.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.25-26
• /
• 2005

This study suggested the occurrence source of weld-defects and its solution methods in a welding of Electrolyte injection hole by pulsed Nd:YAG laser. In experiment, the ramp down was used in order that solidification crack was removed. Furthermore, shrinkage stress and heat input were reduced by changing of weld trajectory and defocused distance. As a results of a experiment, a sound weld bead shape and crack-free weld bead can be obtained.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1159-1165
• /
• 2003

The Nd:YAG laser process is known to have high speed and deep penetration capability to become one of the most advanced welding technologies. In spite of its good mechanical characteristics, SM45C carbon steel has a high carbon contents and suffers a limitation in the industrial application due to the poor welding properties. The major process parameters studied in the present laser welding experiment were position of focus, travel speed and laser power.