• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.202-205
• /
• 1995

Developed controller is the part of deflection yoke winding machine which controls the power to form the deflection yoke coil into desired shape after winding. So as to form the deflection yoke coil, it is needed to melt the bonding material which is spreaded on the coil. The heat melt the bonding material which is produced by flowing the current through the winded coil. Therefore, at first it is needed to peel off the enamel from the winded coil so as to flow the current, and then supply the power to produce the heat which form the winded coil into desired shape. Naturally developed controller is composed of the peeling part and the conduction and forming part. All of them consist of the inverter structure and control the output current. The peeling is achieved by low voltage and high AC current, the conduction and forming is by DC current. Developed controller also has a function that detect the resistance of the deflection yoke coil to prevent the damage of the load which is produced by poor peeling.

• Structural Engineering and Mechanics
• /
• v.35 no.4
• /
• pp.387-407
• /
• 2010

In this paper, using perturbation and Galerkin method, the response of a resonant viscoelastic microbeam to an electric actuation is obtained. The microbeam is under axial load and electrical load. It is assumed that midplane is stretched, when the beam is deflected. The equation of motion is derived using the Newton's second law. The viscoelastic model is taken to be the Kelvin-Voigt model. In the first section, the static deflection is obtained using the Galerkin method. Exact linear symmetric mode shape of a straight beam and its deflection function under constant transverse load are used as admissible functions. So, an analytical expression that describes the static deflection at all points is obtained. Comparing the result with previous research show that using deflection function as admissible function decreases the computation errors and previous calculations volume. In the second section, the response of a microbeam resonator system under primary and secondary resonance excitation has been obtained by analytical multiple scale perturbation method combined with the Galerkin method. It is shown, that a small amount of viscoelastic damping has an important effect and causes to decrease the maximum amplitude of response, and to shift the resonance frequency. Also, it shown, that an increase of the DC voltage, ratio of the air gap to the microbeam thickness, tensile axial load, would increase the effect of viscoelastic damping, and an increase of the compressive axial load would decrease the effect of viscoelastic damping.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2465-2470
• /
• 2007

We have analyzed the three-dimensional thermal conduction in anisotropic materials using nonsymmetric-Fourier transforms. And a complete theoretical treatment of the photothermal deflection spectroscopy has been performed for thermal conductivity measurement in anisotropic medium. Thermal conductivity tensor was determined by the deflection angle and phase angle with the relative position between the heating and probe beams. The influence of the parameters, such as modulation frequency of the heating beam, the thermal conductivity tensor, was investigated.

• Computational Structural Engineering
• /
• v.5 no.1
• /
• pp.83-89
• /
• 1992

A practical method of estimating inelastic deflection of reinforced concrete slab under service load is presented. Based on the elastic results of linear finite element analysis and area of reinforcement, inelastic deflection multiplier(.betha.) is evaluated and desired deflection as a measure of serviceability of the designed slab is obtained. Example for the corner supported slab shows that the results from the proposed method agree well with those from the experiment/and nonlinear finite element analysis. Application of the method to the design of irregular slab is also considered.

• Steel and Composite Structures
• /
• v.3 no.6
• /
• pp.451-474
• /
• 2003

Details are given of a cold-formed steel portal framing system that uses simple bolted moment-connections for both the eaves and apex joints. However, such joints function as semi-rigid and, as a result, the design of the proposed system will be dominated by serviceability requirements. While serviceability is a mandatory design requirement, actual deflection limits for portal frames are not prescribed in many of the national standards. In this paper, a review of the design constraints that have an effect on deflection limits is discussed, and rational values appropriate for use with cold-formed steel portal frames are recommended. Adopting these deflection limits, it is shown through a design example how a cold-formed steel portal frame having semi-rigid eaves and apex joints can be a feasible alternative to rigid-jointed frames in appropriate circumstances.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.381-388
• /
• 1988

The heights of the towers of a ropeway are theoretically derived and the result is experimentally verified. The accuracy in the equation of deflection angle obtained by applying the characteristics of catenary curve was confirmed through experiment. By applying these equations the optimal values of the tower heights could be obtained because the deflection angles trade off each other. The deflection angle was measured by using the curve fitting technique.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.4
• /
• pp.323-330
• /
• 1982

The vibration characteristics of continuous span periodically supported beams with moving loads are determined theoretically and experimentally. Moving loads are assumed to travel at constant acceleration with constant magnitude. Analyses by using the Fourier Transform technique are developed to determine the dynamic performance of moving load interacting with multiple and continuous beam. Equation of motion for the moving load is non-dimensionalized. Non-dimensional deflection proflies of continuous beam are presented in detail for the single concentrated moving load with constant acceleration. Experimental moving load and continuous beam models are developed. The maximum deflections at each midpoints 5,7 and 9 span beam are measured and their non-dimensional maximum deflections are presented. The non-dimensional maximum deflection of continuous beam is compared with measured maximum deflection of 9 span beam and found to agree reasonably well. The deflection of continuous beam due to moving load with acceleration is strongly influenced in the resonance region.

• Journal of Advanced Marine Engineering and Technology
• /
• v.29 no.7
• /
• pp.785-794
• /
• 2005

Modern ship hulls of large oil carriers and container carrers have become more flexible with scantling optimization and increase in ship length. On the other hand. as the demand for power has increased with the ship size. shaft diameters have become larger and stiffer. Consequently. the alignment of the propulsion system has become more sensitive to hull girder deflections. resulting in difficulties in analyzing the alignment and conducting the alignment procedure. Accordingly. the frequency of shaft alignment related bearing damages has increased significantly in recent years. The alignment related damages are mostly attributed to inadequate analyses. changes in the design of the vessel. shipyards' practices in conducting the alignment. and a lack of well defined analytical criteria. The hull deflections should be considered at the design stage to minimize the bearing damage caused by hull deflection. Hull deflections can be estimated by analytical approach and reverse calculation using the measured data. The hull girder deflection analysis using the reverse calculation will be introduced in this paper.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.10 no.1
• /
• pp.143-152
• /
• 2002

European side impact analysis of an electric vehicle was done using the robust design method. In order to minimize VC as well as rib deflection, the injury response table which consists of rib deflection and VC response table has been introduced. The sensitivities and interactions are almost the same when it was compared with those of rib deflection and VC response table. Using internal energy of the factors, the starting time of dummy rib deflection and the contact average velocity, the internal energy and time-velocity response table were introduced. It is shown that the results of the new response tables have the similar characteristics to those of the Injury response table. It is suggested that the internal energy and time-velocity response table should be utilized to minimize injuries.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1391-1394
• /
• 2007

In order for Hypoid gear development. Gears are required to sustain heavy loads or on applications where the gear box is made or a material with a different coefficient of thermal expansion form that or the gears and shafts, it is desirable to make a deflection and contact check under load. The deflection test is performed in the actual gear mounting using completely processed gear. This test should cover the full operating range of gear loads from no load to peak load. Under peak load the contact pattern should extend to the tooth boundaries without showing a concentration of the contact pattern at any point on the tooth surface.